《【 畢業設計 畢業論文】自動化專業 計算機 畢業論文 文獻翻譯 中英文》由會員分享，可在線閱讀，更多相關《【 畢業設計 畢業論文】自動化專業 計算機 畢業論文 文獻翻譯 中英文（18頁珍藏版）》請?jiān)谘b配圖網上搜索。

1、外文原文 Computer Control W. Daley & R. Carey GTRI, Georgia Institute of Technology, Atlanta, GA 30332 INTRODUCTION This chapter discusses both the system and subsystem control computers. The purpose of the system control computer is to provide a single machine that will allow a user to control t

2、he operation of the CHARA Array. This computer will allow the user to acquire astronomical data, align optics, and perform diagnostics and is also responsible for interfacing with remote users and providing them access to the system. The subsystem control computer, on the other hand, communicates be

3、tween the system control computer and each of the subsystems, controlling motors, solenoids, et cetera, and transmitting status reports on each of the subsystems to the central computer. SYSTEM CONTROL COMPUTER U.2.1 Functionality The system will provide a graphical user interface with the fol

4、lowing functionality: _ Communicate directly with each subsystem _ Control all subsystems together as one unit _ Acquire and store data _ Display the state of the optics graphically _ Display environmental conditions _ Display any subsystem error conditions _ Control individual telescopes and

5、 all subsystems U.2.2. Requirements The system computer needs to: _ Perform multiple tasks concurrently _ Share file information with other computers _ Communicate simple commands and data to subsystems _ Monitor and record real-time control information of the subsystems _ Provide Internet ac

6、cess for remote users _ Provide reliable and maintainable software . Communication and control signals Design Hardware A SUN Microsystems SPARC 10 was chosen for the system control computer. This machine uses the UNIX based Solaris 1.1 operating system which will al

7、low multiple users to log-on and multiple programs to be executed concurrently. The SPARC 10 supports an Ethernet network interface which will be used to send simple commands and data to the individual subsystems. This network will also be used for aligning and trouble-shooting problems with the sys

8、tem. The operating system supports the Network File System (NFS) which will be used to transfer files between the various subsystems. The workstation will have a replicated memory card installed, which will be connected by fiber-optic cables to replicated memory cards installed in each of the subsy

9、stem computers. This real-time replicated shared-memory system will connect computers at high data speeds (150 Mbits/sec) with minimal application-to-application transport delay. This network will allow the system control computer to monitor the status of the control variables located on the individ

10、ual subsystems, by looking at its local memory located on the replicated memory card. The network will also allow the subsystem computers to do real-time control synchronization by using local variables located on the replicated memory cards. The system control computer will generate a TTL clock wh

11、ich will be distributed to all the subsystems over a fiber optic network. This clock will be used to synchronize all the motor controllers to insure stable system operation. The connections between the system computer and the other subsystems can be seen in Figure U.1.

12、 . Software object design. Software The software will be developed in the C++ language, which supports object oriented software design and implementation. The use of object oriented programming (Figure U.2) will ensure that the software is developed so that it is reliable and ma

13、intainable. This is done by forcing the consideration of total system functionality and design before any code is written. The program is designed as a number of objects that interact with each other through well-defined interfaces. This means that all objects in the program have to be identified an

14、d the data flow between them determined. Once an object has been developed and its associated functions have been debugged, it can be used on any subsystem that has similar requirements without any modification. It also means that an object can be updated without interfacing with the rest of the sys

15、tem. The Graphical User Interface (GUI) will be developed using the X Windows standard and the Motif widget toolset. This GUI supports widgets that implement pop-up windows, scroll bars, push buttons, list boxes, edit boxes, etc. These widgets will allow the user to interact with the GUI using a mo

16、use and keyboard. The GUI will allow objects, like mirrors, telescopes and beam paths to be drawn graphically on the screen. The user will manipulate these objects by clicking the mouse on the object and dragging it to its new location. This will be useful in inserting or removing a mirror from the

17、 optical path, for example. Risks The technical risks associated with the successful completion of this aspect of the project would be minimal. Options There are many options to the various parts of the system control computer but only a few possibilities will be discussed here. The system

18、computer could have been another type of workstation such as HP, IBM, Silicon Graphics and DEC but they each have their limitations of networking, processing speeds, hardware and software availability. The SUN workstation provides the most cost effective solution to the problem. An IBM 486 computer

19、could be used but it would have to run a multi-tasking, multi-user operating system to successfully implement the system control computer. The operating systems that currently run on IBM 486s that meet these requirements are UNIX and Windows NT. SUN's UNIX implementation is a lot better than any UNI

20、X that runs on a PC, and Windows NT is an unproven product. The replicated memory network could be replaced by a deterministic network like a token- ring network. This solution would require that software be developed to handle the message passing between the various subsystems. Although this is no

21、t an impossible task, it adds a level of complexity to the system software design, that makes it harder to develop and extremely difficult to maintain. C could have been chosen as the development language, since it is well known and widely used. Although C is a powerful language, it does not force

22、the developer to write maintain- able software. Instead, it leaves it up to the developer to ensure that there are no conflicts between the various modules in the system. In very large software projects like the CHARA Array, a lot of diligence and documentation is required on the part of the develop

23、ers, to ensure that there are no side effects from one module interacting with another. In C, there is also no well defined mechanism to ensure that code developed for one module will work in another module. C++, on the other-hand, eliminates side effects by hiding the data and function implementati

24、ons from the rest of the program. This ensures that data is only manipulated by member functions that use the proper procedures, thus eliminating adverse side effects which in most cases reduce the integrity of the software. DATA ACQUISITION COMPUTER While the system control computer is responsi

25、ble for the real time control aspects of the Array another system is required for data logging and reduction. This system will be required to log any data produced by the fringe tracking and imaging systems, produce real-time estimates of visibilities and allow access to, but not control of, many of

26、 the Array subsystems. This computer will allow the operator, or a visiting astronomer, to inspect data on the fly and perform basic data reduction without interfering the operation of the Array. A Sun Sparc or equivalent UNIX machine connected to the local area network should be adequit for this jo

27、b. SUBSYSTEM CONTROL COMPUTER Functionality The subsystems will provide the following functionality: _ Communicate with each subsystem and central controller _ Control necessary control devices (motors, solenoids, etc.) _ Transmit current subsystem status to the central controller _ Trans

28、mit error conditions to the central controller Requirements The subsystem computer needs to: _ Perform multiple tasks concurrently _ Respond to simple commands from the system control computer _ Control hardware devices (motor controllers, digital I/O, etc.) _ Monitor environmental condition

29、s _ Provide reliable and maintainable software Design Methodology There were two hardware design methodologies considered: The first method was to make the initial cost of the system as low as possible while providing the desired functionality. This could be accomplished by determining and

30、defining all the communication protocols between each subsystem. As long as the communication protocols were well defined and adhered to, it would not matter what hardware platform was used for each subsystem. Each subsystem could then be optimized to be the most cost effective for its functionality

31、. For example, a subsystem that monitors environmental variables and controls a set of mirrors could be built on a low-cost STD bus system, whereas a system that needs to acquire real-time data and perform FFT processing would use a VME type system with DSP processor cards installed. Although this d

32、esign methodology would produce the cheapest initial system, it would be very expensive to maintain in the long run. This is because there would have to be someone who is familiar with each of the different hardware and software architectures used. Such individuals are typically hard to come by. Als

33、o, the stocking of spare parts to fix failed boards would be cost prohibitive, since spares would have to be stocked for each different subsystem. The second design methodology was to make the software development and long-term maintenance as simple and cost effective as possible. This was done by

34、using the same base computer system in all the subsystems. While this might be overkill for some subsystems, it will make for a more reliable and maintainable overall system in the long run. The CHARA solution is to specify a BUS architecture, the main processing board, and a real-time operating sys

35、tem. Various I/O, D/A, A/D, and DSP boards are specified that can be used if needed by the subsystems. This means that there is a base configuration that is the same across all subsystems, with modularity built in with the choice of interface boards. This solution allows software developed for one s

36、ubsystem to be used on another subsystem, and the same spare parts can be stocked for all subsystems. Choosing the correct BUS was very important and the following Buses were considered because of the availability of real-time hardware and software: _ PC _ Multibus _ STD _ STD-32 _ VME _ VXI

37、 Table U.1 shows a comparison of these options; the different category ratings are discussed below. TABLE U.1. Comparison of available BUS architectures Category Rating Description: _ Ethernet Support Excellent CPU cards have Ethernet ports built in, and software drivers supplied

38、 Very Good Ethernet cards and drivers are available from many vendors Good: Ethernet cards and drivers are available from a few vendors Fair: Ethernet cards and drivers are available from one vendor Poor: No Ethernet cards or drivers available _ DSP Support Excell

39、ent: Many different vendors with very high speed computational boards Very Good: Many different vendors Good: A few different vendors Fair: One vendor Poor: No vendors _ A/D, D/A, & Digital I/O Support Excellent: Many different vendors with many different boards Very G

40、ood: Many different vendors Good: A few different vendors Fair: One vendor Poor: No vendors _ Motor Controller Support Excellent: Many different vendors with many different boards Very Good: Many different vendors Good: A few different vendors Fair: One ve

41、ndor Poor: No vendors _ Real-Time O/S Support Excellent: BUS supports many different processors and O/Ss Very Good: BUS supports many different O/Ss Good: BUS supports a few different O/Ss Fair: BUS supports one O/S Poor: None _ Cost Excellent: Many low-cost boards

42、and software (<$500) Very Good: Few low-cost boards and software Good: Many medium-cost boards and software ($500 { $1500) Fair: Few medium-cost boards and software Poor: Only high-cost boards and software (>$1500) _ Reliability Excellent: Very high MTBF, very good mechan

43、ical support for cards Very Good: High MTBF, good mechanical support for cards Good: Average MTBF, average mechanical support for cards Fair: Low MTBF, poor mechanical support for cards Poor: Very low MTBF, very poor mechanical support for cards Assigning a scale of 1 ~ 5, w

44、ith 5 being excellent and 1 being poor, gives the following overall rating shown in Table U.2. All categories were determined to be of equal importance and no weighting was used. Based on this selection criteria， the VME BUS scored the highest and was chosen for the subsystem controllers. The avail

45、able software tools and development environment were not taken into consideration but will be discussed in a later section. Hardware A Motorola-based CPU board was chosen as the central processor for the VME BUS because it is widely supported by the real-time operating systems. The CPU board wil

46、l have the following specification: 25 MHz MC68040 microprocessor with 8KB of Cache TABLE U.2 Rating of available BUS architectures _ 8 MBytes of DRAM _ Ethernet interface _ Sockets for on-board ROM/EPROM The base system will also contain a replicated shared-memory fiber-optic network

47、card, which will allow each subsystem to have an exact copy of a block of memory. This real-time replicated shared-memory system will connect computers at high data speeds (150Mbits/sec) with minimal application-to-application transport delay. Variables stored in this block of memory will be availab

48、le on all subsystems as local variables. This will make developing the system software much easier, since time will be spent developing software to control the subsystem as opposed to implementing complex communication schemes between the individual subsystems. For example, the OPLE subsystem needs

49、error information from the fringe tracking subsystem, which can be implemented by having the fringe tracker write the error information to a specific memory location and then set a flag in another memory location. The OPLE subsystem would read the error information when the flag is set, and then cle

50、ar the flag. In this approach, no software development need be expended on the communication between the OPLE and fringe tracker, since it is all handled in hardware. The replicated memory system will also be invaluable for trouble-shooting and system debugging, since the control variables of each s

51、ubsystem can be seen and recorded at the central computer. The remaining cards that will go in the VME chassis will be optional and depend on the functionality of the subsystem. A diagram of a typical subsystem can be seen in Figure U.3. Software The software will be developed in the C++ langua

52、ge, which supports object-oriented software design and implementation. The use of object-oriented programming will ensure that the software is developed for reliability and maintainability, since it forces the software to be completely designed before any code is written. It is anticipated that the

53、CHARA Array will use an open system that will adjust to the needs of its users. The software should thus be designed to accommodate these changes and modifications as painlessly as possible. The program is designed as a number of objects that interact with each other through well-defined interfaces

54、. This means that all the objects in the program have to be identified and the data flow between them determined. Once an object has been developed and its associated functions have been debugged, it can be used on any subsystem that has similar requirements without any modification. VxWorks by Wi

55、nd River Systems is a real-time operating system that will be used on the subsystem controllers. This UNIX-like operating system will allow multiple tasks to run concurrently while maintaining their priority schemes. This means that the task with the highest priority will execute whenever it needs t

56、o, while other lower priority tasks will be put on hold. VxWorks also allows the user to log in from remote locations and interact with tasks running on the system. The software development environment will consist of a product called Object Center from Centerline Software, Inc. This product is hos

57、ted on a Sun Sparc Station and provides an intuitive user-friendly environment to develop, debug, and document C++ code. . Subsystem controller. Risks The technical risks associated with the successful completion of the subsystem design and integration are not significant. The areas that wo

58、uld be of most concern would be the development of low-level device drivers to control various pieces of hardware. In most cases this should not be necessary, as it is anticipated that we will be able to purchase most of these drivers with the associated equipment. 翻譯 計算機控制 W. Daley & R. Carey G

59、TRI, 亞特蘭大喬治亞技術協會，GA30332 ．簡介 本章討論系統以及子系統控制計算機。系統控制計算機的目的是，提供單一的機器，它能夠允許用戶操作控制 CHARA 排列。這一部計算機將會允許用戶獲得龐大的數據，進行光學排列，同時進行診斷，并且負責和比較偏遠的用戶接口以使他們有機會接觸系統。另一方面，子系統控制計算機，通信于系統控制計算機以及每一個子系統，控制馬達，螺線管，等等之間，并且將每一個子系統的狀態報告?zhèn)魉徒o中央計算機。 . 系統控制計算機 U.2.1. 功能性 系統將會提供具有以下功能的一個圖形用戶界面： -直接地與每個子要系統溝通； -將所有子系統視為一個整體進

60、行控制； -獲取并存儲數據； -圖解式地顯示光學的狀態； -顯示環境狀況； -顯示任何子系統的錯誤情況； -控制個別望遠鏡和所有子系統。 U．2.2 要求 系統計算機需要： -能同時運行多個任務； -和其他計算機共享文件信息； -向子系統傳達簡單的指令和數據； -監視并記錄子系統的實時控制信息； -提供英特網通路給遙遠的用戶； -提供可靠的和可維持的軟件。 圖 U.1 通信和控制信號 . 設計 硬件 系統控制計算機選擇（SUN）微系統 SPARC 10[SUN公司的工作站系統]。這部機器使用UNI

61、X的基于Solaris 1.1 操作系統，它允許多用戶注銷和多程序的同時運行。SPARC 10支持一個以太網接口——用于向個別子系統傳送簡單的指令和數據。這一個網絡也用來矯正和系統問題解析。操作系統支持將會用來在各種不同的子系統之間轉移文件的網絡文件系統 (NFS)。 工作站裝有復制存儲卡，它通過光纖與安裝在子系統計算機中的復制存儲卡連接。這種實時復制共享存儲系統，能夠在最小的申請-應用傳輸延時內，以高達150Mbits/s的速度連接到計算機。這種網絡允許系統控制計算機，通過觀察位于復制存儲卡的局部存儲器，監視位于個別子系統中的控制變量的狀態。通過光纖網絡，系統控制計算機將產生的一個TTL時

62、鐘分配到所有的子系統。時鐘用來使所有的控制器同步工作，從而保證系統操作的穩定性。系統計算機和子系統的連接如圖U.1所示。 U2.3.2 軟件 我們用C++語言開發此軟件，它支持對象定位的軟件設計和執行。使用對象定位程序（圖U.2）能夠保證軟件開發的可靠性和可維持性。在任何代碼寫入之前必須考慮到總系統的功能性和設計本身，必須這樣使用對象定位程序。程序設計有許多對象，這些對象通過明確定義的接口相互聯系。這就意味著，必須要識別程序中的所有對象，同時這由它們之間的數據流決定。一旦開發了一個對象，并且調試了它的聯想機能，那么它就可以無需任何修改地應用在那些具有相似要求的子系統上。也就是說，在不連接

63、其它系統的情況下可以更新目標對象。 圖U.2 軟件對象設計 可以運用X Windows標準和圖形裝飾工具組開發圖形用戶界面（GUI）。圖形用戶界面（GUI）支持具有彈出窗口，滾動條，按鈕，列表框，編輯框等等的窗口小部件。這些窗口部件允許用戶通過鍵盤，鼠標與圖形用戶界面進行通信。圖形用戶界面允許對象如鏡子，望遠鏡，光路能夠形象地在屏幕上顯示出來。用戶可以通過點擊對象上的鼠標，以及拖拽到一個新的位置來實現對對象的操作。比如，這將會在插入或把一面鏡子從光學的路徑上移開方面非常有用。 U.2.4 風險 與計劃的成功完成這一個方面有關的技術上

64、的危險會是最小的。 U.2.5 選項 基于系統控制計算機的很多部分的選項有很多，但是在這里我們只討論其中的一些可能性。 系統計算機也可能是另外類型的工作站，象HP，IBM，Silicon Graphics，DEC等，但是他們每一個在網絡，處理速度，硬件和軟件有效性上都有局限性。SUN工作站在這個問題上提供了最為有效的解決途徑。我們可以使用IBM 485計算機，但是它要成功的完成系統控制計算機的話就必須運行一個多用戶，多任務操作系統。目前，在IBM 486s上運行的能夠滿足這些要求的操作系統有UNIX，Windows NT。SUN’s UNIX在個人計算機上的運行效果比其它UNIX要好的

65、多，況且Windows NT的效果還有待證明。 復制存儲網絡可能會被象令牌網網絡這樣的確定性的網絡取代。這個解決方案要求軟件開發到：能夠處理在不同的子系統之間交換的信息。盡管這個任務不可能實現，它將系統軟件設計的復雜性提高了一個水平，使得開發十分不易，維護更加困難。 鑒于C語言比較有名并且應用廣泛，所以選擇C語言作為開發語言。盡管C語言的功能十分強大，它并不要求開發者寫出可以維持的軟件。相反，它使得軟件開發者要保證系統中的眾多模塊之間沒有沖突。在很大的軟件工程當中，如CHARA Array，開發者要花很大功夫，并且要用到很多文件，以保證模塊之間沒有副作用產生。在C語言中，也沒有明確定義的機

66、制來保證，在一個模塊中開發中的代碼能夠在另一個模塊中也能正常使用。從另外一方面講，C++，通過隱藏?cái)?shù)據以及程序其他執行功能來消除副作用。這能確保只有使用恰當程序的人員才能操作數據，因此，消除大多數情況下產生的不利的副作用簡化了系統的完整性。 U.3 采集數據計算機 當系統控制計算機負責排列的實時控制方面，那么，數據分段和約簡就要用到另外一個系統。這個系統用于將邊緣跟蹤和成像系統產生的數據分段，對能見度產生實時評估，并且允許有權使用許多排列子系統，但不是控制。計算機允許操作者或者訪問天文學家檢測飛行體上的數據，并且無需妨礙排列操作就可以進行原始數據約簡。連接到局域網的一個Sun Sparc或者等價的UNIX機器正好適合這個工作。 U.4 子系統控制計算機 U.4.1 功能性 子系統提供以下功能： -同每個子系統和中央控制器進行通訊； -控制必要的控制設備（馬達，螺線管等等）； -將當前子系統狀態傳給中央控制器； -將錯誤情況傳送給中央控制器； U.4.2 要求 子系統計算機必須： -同時運行多個任務； -能夠?qū)ο到y(tǒng)控制計算機發出的簡單命令作出反應； -