軸類零件的加工工藝說明書和加工卡片,零件,加工,工藝,說明書,仿單,以及,卡片 零件2(加工外輪廓) SK01.MPF T01G90G95 M03 S500 G00X70 Z5 _CNAME=“L01” R105=1 R106=0.1 R108=2 R109=0 R110=1.5 R111=0.30 R112=0.15 LCYC95 M03 S800 R105=5 LCYC95 G00 X70 Z100 T02M03S300 G00X70Z5 Z-61.5 G01X48F0.08 X52Z-59.5 Z-61.5 X2 G00X80 Z100 M05 M02 Sk02.MPF 加工零件1左端內(nèi)輪廓 T04G90G95 M03 S500 G00X20Z5 _CNAME=“L02” R105=3 R106=0.1 R108=1.5 R109=0 R110=1.5 111=0.2 R112=0.1 LCYC95 G00X20 Z5 M03 S800 R105=7 LCYC95 G00X20 Z100 T01 M03 S500(加工零件1左端外輪廓) G00X70 Z5 _CNAME=“L03” R105=1 R106=0.2 R108=2 R19=0 R110=1.5 R111=0.3 R112=0.15 LCYC95 G00X70 Z5 M03 S800 R105=5 LCYC95 G00X70 Z100 T05 M03 S500 (加工R18、R10圓弧) G00 X80 Z5 Z-20 (將起始點(diǎn)放在槽中間，割槽后可消除接刀痕跡) G01 X72.2 F0.2(0.2mm為精加工余量) L04 P11 G00 X60 Z-20 S800 G01 X52.2 F0.1 L04 G00 X70 Z100 T02 M03 S300 (割2-4×3mm槽) G00 X60 Z5 Z-9(割刀用左刀位點(diǎn)) G01 X44 F0.08 G00 X55 Z-22 G01 X44 F0.08 G00 X70 Z100 M05 M02 SK03.MPF(加工零件1右端外輪廓) T01 G90 G95 M03 S500 G00 X70 Z5 _CNAME=“L05” R105=1 R106=0.1 R108=2 R109=0 R110=1.5 R111=0.3 R112=0.15 LCYC95 M03 S800 R105=5 LCYC95 G00 X70 Z5 M03 S500 F0.3(加工橢圓) G00 X55 Z-20 R20=8.285 MA1:G158 X=R20 L06 R20=R20-2 IF R20>=0.285 GOTOB MA1 G00 X55 Z-20 M03 S800 F0.15 G158 R20=0 L06 G00X70 Z100 T02 M03 S300(割5×1.5mm退刀槽) G00 X30 Z5 Z-25 G01 X21 F0.08 X25 Z-24 X21 G00X30 Z100 T03 M03 S450 (加工M24×1.5螺紋) R100=24 R101=0 R102=24 R103=-20 R104=1.5 R105=1 R106=0.2 R109=5 R110=2.5 R111=0.975 R112=0 R113=6 R114=1 LCYC97 G00X70 Z100 M05 M02 L01.SPF G01X23 Z0 X25 Z-1 Z-15 X30.3 X36 Z-43.5 Z-45 X49 X52 Z-46.5 Z-62 G00X65 M02 L02.SPF G01 X36 Z0 X30Z-30 X25 Z-45 X20 M02 L03.SPF G01 X44 Z0 G03 X50 Z-3 CR=3 G01 Z-70 X56 G03 X62 Z-73 CR=3 G01 Z-80 G00 X65 M02 L04.SPF G91 G01 X-2 Z-10.38 G03 X-12.79 Z-14.54 CR=18 G02 X11.79 Z-18.08 CR=10 G01 X2 G00 Z43 G01 X-1 G90 M02 L05.SPF G01 X21 Z0 X24 Z -1.5 Z-25 X46 Z-50 X56 G03 X62 Z-53 CR=3 G00X65 M02 L06.SPF R1=45 R2=25 R3=35 MA2:R4=R2*SQRT(R1*R1-R3*R3)/R1 G01X=2*R4 Z=R3-60 R3=R3-0.05 IF R3>=17.64 GOTOB MA2 G91 X5 G90 Z-20 M02