喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有,,請放心下載，原稿可自行編輯修改 【QQ：414951605 可咨詢交流】===================== 喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有,,請放心下載，原稿可自行編輯修改 【QQ：1304139763 可咨詢交流】===================== 喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有,,請放心下載，原稿可自行編輯修改 【QQ：1304139763 可咨詢交流】=====================

大連交通大學2017屆本科生畢業設計（論文）外文翻譯 Gate Design Gates are a transition zone between the runner system and the cavity. The location of gates is of great importance for the properties and appear- ance of the finished part. The melt should fill the entire cavity quickly and evenly. For gate design the following points should be considered: – – – Locate the gate at the thickest section Note gate marks for aesthetic reasons Avoid jetting by modifying gate dimen- sions or position Balance flow paths to ensure uniform filling and packing Prevent weld lines or direct to less critical sections Minimize entrapped air to eliminate burn marks Avoid areas subject to impact or mechan- ical stress Place for ease of degating – – – – – Single vs. multiple gates. Unless the length of the melt flow exceeds practical limits a single gate is the preferred option. Multiple gates always create weld lines where the flows from the separate gates meet. A distinction can be made between center and edge gating of a part. Center gated parts show a radial flow of the melt. This type of gate is particularly good for symmetrical parts, such as cup shaped products or gears, because it will assure more uniform distribu- tion of material, temperatures, and packing, and better orientation effects it gives very pre- dictable results. On the other hand, linear flow and cross flow properties often differ. In flat parts, this can induce additional stress and results in warpage or uneven shrinkage. Because of their simplicity and ease of manu- facture, edge gates are the most commonly used. These work well for a wide variety of parts that are injection molded. Long narrow parts typically use edge gates at or near one end in order to reduce warpage. 外文原文 But it is very difficult to mold round parts using this type gate, as they tend to warp into an oval shape. While a single gate into the body of the part might incur a higher initial tool cost, lower scrap rates and higher part quality will quickly justify this expense. Gate dimensions. The cross section of the gate is typically smaller than that of the part runner and the part, so that the part can easily be "de-gated" (separated from the runner) without leaving a visible scar on the part. The gate thickness is typically between one half and two-thirds the part thickness. Since the end of packing can be identified as the time when the material in the gate drops below the freeze temperature, the gate thickness con- trols the packing time. Pressure Locate the gate in the thickest section to ensure adequate pressure for packing out the part. This will also help prevent sink marks and voids forming. Orientation Molecular orientation becomes more pro- nounced in thin sections, the molecules usually align themselves in the flow direction. High degrees of orientation result in parts having unaixal strength, resistance to loading only in one direction. To minimize molecular orientation the gate should be located so that as the melt enters the cavity it is diverted by an obstruction such as the cavity wall or an ejection pin. A larger gate will reduce frictional heating, permit lower velocities, and allow the applica- tion of higher packing pressure for a longer period of time. If appearance, low residual stress, and better dimensional stability were required then a larger gate would be advan- tageous. A minimum size of 0.8 mm is recommended for unreinforced materials. Smaller gates may induce high shear and thus thermal degrada- tion. Reinforced thermoplastics require slight- ly larger gates > 1 mm. As a rule it should not exceed the runner or sprue diameter. The maximal land length should be 1 mm. Weld lines Place gates to minimize the number and length of weld lines or to direct weld lines to positions that are not objectionable to the function or appearance of the part. When weld lines are unavoidable try to locate the gates close to the weld line location this should help maintain a high melt temperature that is beneficial to a strong weld line. Gate location. Location items to include: consider Appearance Whenever possible locate gates on non- visual surfaces thus eliminating problems with residual gate vestiges after the gate has been removed. Stress Avoid areas exposed to high external stress (mechanical or impact). The gate area has high residual stresses and also rough surfaces left by the gate act as stress concentrators. Figure 65 Warpage due to unfavorable gate location. Glass fiber reinforced materials Fiber-filled materials require larger gates to minimize breakage of the fibers when they pass through the gate. Using small gates such as submarine, tunnel, or pin gates can damage the fillers in filled materials. Gates that deliver a uniform filling pattern (such as an edge gate) and thus, a uniform fiber orien- tation distribution are preferable to point-type gates. Fiber orientation will normally be the determining factor for warpage problems with this type of material and the gate location and choice of gate type are 2 of the primary factors in controlling the orientation. In general, there will be a higher glass fiber orientation in thinner wall sections, e.g. less than 2 mm and as injection speed increases. A high injection speed is required to obtain a smooth surface. The direction of orientation is influenced by gate type and location and, of course, by the shape of the product (see Figure 63). Warpage An incorrectly dimensioned or located gate may also result in undesirable flow patterns in the cavity. This can lead to moldings with visible weld line (see Figure 64). Undesirable flow patterns in the cavity can also lead to deformation by warping or bending (see Figure 65). Manually trimmed gates. Manually trimmed gates are those that require an operator to separate parts from runners during a sec- ondary operation. The reasons for using man- ually trimmed gates are: – The gate is too bulky to be sheared from the part as the tool is opened. Some shear-sensitive materials (e.g., PVC) should not be exposed to the high shear rates inherent to the design of automati- cally trimmed gates. Simultaneous flow distribution across a wide front to achieve specific orientation of fibers of molecules often precludes auto- matic gate trimming. – – Gate types trimmed from the cavity manually include sprue gates, edge gates, tab gates, overlap gates, fan gates, film gates, diaphragm gates, external rings, and spoke or multipoint gates. Figure 66 Sprue gate. Sprue Gate Recommended for single cavity molds or for parts requiring symmetrical filling. This type of gate is suitable for thick sections because holding pressure is more effective. A short sprue is favored, enabling rapid mold filling and low-pressure losses. A cold slug well should be included opposite the gate. The disadvantage of using this type of gate is the gate mark left on the part surface after the runner (or sprue) is trimmed off. Freeze-off is controlled by the part thickness rather than determined the gate thickness. Typically, the part shrinkage near the sprue gate will be low; shrinkage in the sprue gate will be high. This results in high tensile stresses near the gate. The starting sprue diameter is controlled by the machine nozzle. The sprue diameter here must be about 0.5 mm larger than the nozzle exit diameter. Standard sprue bushings have a taper of 2.4 degrees, opening toward the part. Therefore, the sprue length will control the diameter of the gate where it meets the part; the diameter should be at least 1.5 mm larger than or approximately twice the thick- ness of the part at that point. The junction of sprue and part should be radiused to prevent stress cracking. – A smaller taper angle (a minimum of one degree) risks not releasing the sprue from the sprue bushing on ejection. A larger taper wastes material and extends cooling time. Non-standard sprue tapers will be more expensive, with little gain. – – Figure 67 Edge gate. Edge Gate The edge or side gate is suitable for medium and thick sections and can be used on multi- cavity two plate tools. The gate is located on the parting line and the part fills from the side, top or bottom. The typical gate size is 80% to 100% of the part thickness up to 3.5 mm and 1.0 to 12 mm wide. The gate land should be no more than 1.0 mm in length, with 0.5 mm being the optimum. Tab Gate A tab gate is typically employed for flat and thin parts, to reduce the shear stress in the cavity. The high shear stress generated around the gate is confined to the auxiliary tab, which is trimmed off after molding. A tab gate is often used for molding P. The minimum tab width is 6 mm. The minimum tab thickness is 75% of the depth of the cavity. Figure 68 Tab gate. Overlap Gate An overlap gate is similar to an edge gate, except the gate overlaps the wall or surfaces. This type of gate is typically used to eliminate jetting. The typical gate size is 10% to 80% of the part thickness and 1.0 to 12 mm wide. The gate land should be no more than 1.0 mm in length, with 0.5 mm being the optimum. Fan Gate A fan gate is a wide edge gate with variable thickness. This type is often used for thick- sectioned moldings and enables slow injec- tion without freeze-off, which is favored for low stress moldings or where warpage and dimensional stability are main concerns. The gate should taper in both width and thickness, to maintain a constant cross sectional area. This will ensure that: Figure 69 Overlap gate. – – – The melt velocity will be constant. The entire width is being used for the flow. The pressure is the same across the entire width. As with other manually trimmed gates, the maximum thickness should be no more than 80% of the part thickness. The gate width varies typically from 6 mm up to 25% of the cavity length. Figure 70 Film or flash gate. Film or Flash Gate A film or flash gate consists of a straight runner and a gate land across either the entire length or a portion of the cavity. It is used for long flat thin walled parts and provides even filling. Shrinkage will be more uniform which is important especially for fiber reinforced ther- moplastics and where warpage must be kept to a minimum. The gate size is small, typical- ly 0.25mm to 0.5mm thick. The land area (gate length) must also be kept small, approx- imately 0.5 to 1.0 mm long. Figure 71 Internal ring gate. Diaphragm Gate A diaphragm gate is often used for gating cylindrical or round parts that have an open inside diameter. It is used for single cavity molds that have a small to medium internal diameter. It is used when concentricity is important and the presence of a weld line is not acceptable. Typical gate thickness is 0.25 to 1.5 mm. External Ring Gate This gate is used for cylindrical or round parts in a multicavity mold or when a diaphragm gate is not practical. Material enters the exter- nal ring from one side forming a weld line on the opposite side of the runner this weld line is not typically transferred to the part. Typical gate thickness is 0.25 to 1.5 mm. Figure 72 External ring gate. Figure 73 Multi-point gate. Spoke Gate or Multipoint Gate This kind of gate is used for cylindrical parts and offers easy de-gating and material savings. Disadvantages are the possibility of weld lines and the fact that perfect roundness is unlikely. Typical gate size ranges from 0.8 to 5 mm diameter. Automatically trimmed gates. Automatically trimmed gates incorporate features in the tool to break or shear the gate as the molding tool is opened to eject the part. Automatically trimmed gates should be used to: – Avoid gate removal as a secondary operation. Maintain consistent cycle times for all shots. Minimize gate scars. – Figure 74 Pin gates. – Gate types trimmed from the cavity automati- cally include pin gates, submarine (tunnel) gates, hot runner gates, valve gates. Pin Gates Pin gates are only feasible with a 3-plate tool because it must be ejected separately from the part in the opposite direction The gate must be weak enough to break off without damaging the part. This type of gate is most suitable for use with thin sections. The design is particularly useful when multiple gates per part are needed to assure symmetric filling or where long flow paths must be reduced to assure packing to all areas of the part. Gate diameters for unreinforced thermoplastics range from 0.8 up to 6 mm. Smaller gates may induce high shear and thus thermal degrada- tion. Reinforced thermoplastics require slight- ly larger gates > 1 mm. The maximal land length should be 1 mm. Advised gate dimen- sions can be found in Figure 74. Figure 75 Dimensions of gates (* wall thickness larger than 5 mm should be avoided). Submarine (tunnel) Gates A submarine gate is used in two-plate Figure 76 Tunnel gate. mold construction. An angled, tapered tunnel is machined from the end of the runner to the cavity, just below the parting line. As the parts and runners are ejected, the gate is sheared at the part. The tunnel can be located either in the moving mold half or in the fixed half. A sub-gate is often located into the side of an ejector pin on the non-visible side of the part when appear- ance is important. To degate, the tunnel requires a good taper and must be free to bend. Typical gate sizes 0.8 mm to 1.5 mm, for glass reinforced materials sizes could be larger. Hot Runner Gates Hot runner gates are also known as sprue- less gating. The nozzle of a runnerless mold is extended forward to the part and the mate- rial is injected through a pinpoint gate. The face of the nozzle is part of the cavity surface; this can cause appearance prob- lems (matt appearance and rippled surface). The nozzle diameter should therefore be kept as small as possible. Most suitable for thin walled parts with short cycle times, this avoid freezing of the nozzle. Figure 77 Hot runner gates. Valve Gates The valve gate adds a valve rod to the hot runner gate. The valve can be activated to close the gate just before the material near the gate freezes. This allows a larger gate diameter and smoothes over the gate scar. Since the valve rod controls the packing cycle, better control of the packing cycle is maintained with more consistent quality. Figure 78 Valve gate. Figure 79 Basic principle of cooling channels. Mold Cooling Mold cooling serves to dissipate the heat of the molding quickly and uniformly. Fast cooling is necessary to obtain economical production and uniform cooling is required for product quality. Adequate mold temperature control is essential for consistent The layout of the cooling circuit close attention especially if you molding. warrants consider cooling typically accounts for two thirds of a products cycle time. Optimal properties of engineering plastics can be achieved only when the right mold temperature is set and maintained during pro- cessing. The mold temperature has a sub- stantial effect on: Figure 80 Position of cooling channels. – – – – – – Mechanical properties Shrinkage behavior Warpage Surface quality Cycle time Flow length in thin walled parts In particular semi-crystalline thermoplastics need to cool down at optimal crystallization rate. Parts with widely varying wall thickness- es are likely to deform because of local differ- ences in the degree of crystallization. Additionally the required cooling time increas- es rapidly with wall thickness. This calculation is shown in Cooling system equations. Cooling channel configuration. In general, the cooling system will be roughly drilled or milled. Rough inner surfaces enhance turbu- lent flow of coolant, thus providing better heat exchange. Turbulent flow achieves 3 to 5 times as much heat transfer as does non tur- bulent flow. Cooling channels should be placed close to the mold cavity surface with equal center distances in between (see Figures 79 and 80). The mechanical strength of the mold steel should be considered when designing the cooling system. Some thermoplastics may require mold temper- atures of 100°C (212?F) or higher for optimal processing and properties. Effective mold insulation is advised to minimize heat loss between the mold and the machine mounting platens. Insulation boards with low thermal con- ductivity and relatively high compressive strength are commercially available. Figure 81 Sealing and cooling channel lay-out. Care is required in the correct placing of seals; they may be damaged by the sharp edges of the pocket when the mold insert is mounted (see Figure 81). Seals or O-rings should be resistant to elevated temperatures and oils. Guidelines for optimal mold temperature control include: Figure 82 Cooling of the mold. – Independent symmetrical cooling circuits around the mold cavities. Cores need effective cooling (see baffles, bubblers & thermal pins). Short cooling channels to ensure tempera- ture differences between in- and outlet do not exceed 5?C (41?F). Parallel circuits are preferred over serial cooling as shown in Figure 82. Avoid dead spots and/or air bubbles in cooling circuits. Heat exchange between mold and machine should be minimized. Differences in flow resistance of cooling channels, caused by diameter changes, should be avoided. – – – – – – Mold parts that are excessively heated, like sprue bushings and areas near the gates, must be cooled intensively. Rapid and even cooling is enhanced by the use of highly conductive metals, such as beryllium-copper. These metals are used to full advantage in places where it is impossible to place sufficient cooling channels. Beryllium copper transfers twice as much heat as carbon steel and four times as much heat as stainless steel. This does not mean beryllium copper molds will run 4 times faster tan a stain- less steel mold but they will run some thin walled parts significantly faster. Beryllium copper is not recommended for materials that require high mold temperatures as they allow so much heat transfer that it is difficult to maintain adequate heat economically. Figure 83 Example of core cooling by means of baffles: less effec- tive heat discharge at core top Alternative cooling devices. For areas in the mold where it is not possible to use normal drilled cooling channels, alternative methods must be employed to ensure these areas are uniformly cooled with the rest of the part. The methods employed usually include baffles, bubblers, or thermal pins. Baffles Baffles and bubblers are sections of cooling lines that divert the coolant flow into areas that would normally lack cooling, e.g. cores. A baffle is actually a cooling channel drilled perpendicular to a main cooling line, with a blade that separates one cooling passage into two semi-circular channels. The coolant flows in one side of the blade from the main cooling line, turns around the tip to the other side of the baffle, and then flows back to the main cooling line. This method provides maximum cross sec- tions for the coolant, but it is difficult to mount the divider exactly in the center. The cooling effect and with it the temperature distribution on one side of the core may differ from that on the other side and this is the main disad- vantage. The use of a helix baffle will solve the problem by conveying the coolant to the tip and back in the form of a helix. It is useful for diameters of 12 to 50 mm, and makes for a very homogeneous temperature distribu- tion. Another logical development of baffles are single or double-f