盤式刀庫設計-加工中心自動換刀畢業系統設計【含CAD圖紙+文檔資料】,含CAD圖紙+文檔資料,盤式刀庫,設計,加工,中心,自動,畢業,系統,cad,圖紙,文檔,資料 1 目錄 摘 要 ......................................................3 緒論 .........................................................1 1 引言 .......................................................1 1.1 加工中心簡介 ...........................................1 1.1.1 加工中心的發展簡史 .................................1 1.1.2 加工中心的結構組成 .................................3 1.1.3 加工中心的分類 .....................................4 1.1.4 加工中心的發展趨勢 .................................8 2 刀庫的類型 ................................................11 2.1 刀庫的類型 ............................................12 2.2 刀庫的結構與傳動 ......................................15 2.3 刀庫驅動電動機的選定 ..................................18 2.3.1 按負載轉矩選 ......................................18 2.3.2 按加速時的最大轉矩選 ..............................20 2.3.3 校驗 ..............................................21 2.3.4 分配傳動比 ........................................21 3 刀庫傳動機構的設計 ........................................22 3.1 初定刀套線速度 ........................................22 3.2 刀庫傳動方式 ..........................................22 4.1 軸的材料 ..............................................30 4.2 蝸桿軸的初步估算 ......................................30 4.2.1 初步估算軸的最小直徑 ..............................30 4.2.2 選擇聯軸器 ........................................31 4.2.3 確定滾動軸承的類型 ................................32 4.2.4 初步估計蝸桿軸各段的尺寸 ..........................32 4.3 蝸輪軸的初步估算 ......................................33 4.3.1 初步估算軸的最小直徑 ..............................33 4.3.2 確定軸伸處的最小直徑 ..............................34 4.3.3 確定滾動軸承的類型 ................................34 4.3.4 初步估計蝸輪軸的各段尺寸 ..........................35 4.4 軸徑的設計與校核 ......................................35 4.4.1 蝸桿軸 ............................................35 4.4.2 蝸輪軸的計算 ......................................42 2 5 軸承的校核 ................................................48 5.1 蝸桿軸 ................................................48 5.2 蝸輪軸 ...............................................48 6 其它零部件尺寸的設計與計算 ................................50 6.1 回零減速撞塊尺寸的計算 ...............................50 6.2 刀盤與刀套的設計 .....................................51 6.2.1 刀套 .............................................51 6.2.2 刀盤 .............................................52 6.3 刀具（刀座）識別裝置 .................................52 7 液壓系統的設計 ............................................54 7.1 液壓缸的載荷組成和計算 ...............................54 7.2 液壓缸內徑以及其它尺寸的確定 .........................54 7.2.1 計算液壓缸的主要結構尺寸 ..........................55 7.2.2 油缸壁厚的計算 ...................................56 7.2.3 缸底厚度計算 .....................................57 7.3 油缸長度 L 的確定 .....................................58 7.4 液壓系統初步設計 .....................................58 8 PLC 控制 ..................................................60 9 結論 ......................................................63 10 致 謝 .................................................65 參 考 文 獻 .................................................66 3 摘 要 刀庫是自動換刀裝置中最主要的部件之一，其容量、布局以及具體 結構對加工中心的設計有很大影響。 16 刀刀庫是在小型加工中心應用最為廣泛，根據使用的場合和實 際運用的要求，設計了相應的 16 刀的圓盤式刀庫，并且對它的控制進 行了一定的研究。 論文首先對 16 刀刀庫總體設計方案進行闡述，闡述其各部件的工作 原理，然后就刀庫的結構設計與控制分章節對各個部分進行計算與設計。 刀庫的結構設計是本文研究的重點，傳動部分為蝸桿蝸輪的一種減速裝 置，對于該裝置中的蝸桿、蝸輪以及相關的軸都進行了詳細的計算;控 制部分為刀庫送刀部分，由液壓控制和 PLC 控制完成。 關鍵詞：加工中心，刀庫，蝸桿蝸輪，液壓，PLC。 4 ABSTRACT Tool storage is one of the main components of the automatically-trading- knife installment. Its capacity, position and structure have great influence to the design of the machining centre. 16-tool tool storage is widely used in the machining centre. Based on the situation and requirement the 16-tool used, the disc-style tool storage of the 16-tool is designed and some research about its control is made in this paper. The paper illustrates the design project of the 16-tool tool storage firstly, and then explains its operation principle, and at last calculates and designs the structure and control of the tool storage separately by chapters. The design of the structure of the tool storage is the key point of this research. Driving part is a decelerating set of the worm and worm gear. The sizes of the worm, worm gear and axis are calculated. The control parts are tool storage delivering parts, which is completed by the hydraulic pressure and PLC control. Key words: machining centre, Magazine, worm, worm gear, hydraulic pressure, PLC 5