喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有請放心下載，.dwg格式文件為原稿CAD圖紙，可自行編輯修改【QQ：1304139763可咨詢交流】====================
喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有請放心下載，.dwg格式文件為原稿CAD圖紙，可自行編輯修改【QQ：1304139763可咨詢交流】====================
畢業設計（論文）中期報告
題目：燈罩塑料模具設計
系 別 機電信息系
專 業 機械設計制造及自動化
班 級
姓 名
學 號
導 師
2013年 3 月 21 日
1.概述塑件特點
本次設計的塑料件為一燈罩，產品特點為：燈罩外表面必須光滑，且無明顯澆口痕跡；燈罩內壁有呈圓周均布的三個盲孔。在結構設計時需考慮型芯在三個盲孔處的脫模，及模具總體結構的合理性。塑件二維三維圖如圖1和圖2。
圖 1塑件三維圖
圖 2塑件二維圖
2.設計（論文）進展?fàn)顩r
2.1已經完成外文文獻翻譯。
2.2在開題的基礎上進行了計算和結構方案的優化設計，并的完成了模具裝配草圖的繪制。
2.3通過繪制三維圖形獲得塑料件的體積，通過材料的選擇獲得材料的密度，并計算出塑件的質量。通過計算和查閱相關模具設計手冊完成了注塑機的選擇。選型為：G54-S200/400型。相關參數如下：
結構類型： 臥式
理論注射量： 200cm3 最大注射面積：645cm2
最大模具厚度：406mm 鎖模力： 2540KN
最小模具厚度：165mm 定位空直徑： 125mm
模板行程: 260mm 拉桿空間： 290×368mm
噴嘴球半徑： 18mm 噴嘴孔徑： 4mm
注射方式： 螺桿式 螺桿轉速： 16,28,48r/min
螺桿直徑： 55mm 注射壓力: 109MPa
2.4確定主流道、分流道的形式和尺寸。其主流道的尺寸如圖3所示。分流道截面形狀及尺寸如圖4所示，主流道入口直徑d，應大于注塑機噴嘴直徑1mm左右。這樣便于兩者能同軸對準，也使得主流道凝料能順利脫出。主流道入口的凹坑球面半徑R，應該大于注塑機噴嘴頭半徑約2～3mm。反之，兩者不能很好粘合，會讓塑料熔體反噴，出現溢邊導致脫模困難。錐孔粗糙度。主流道的錐角a=2°～4°。過大的錐角會產生湍流或渦流，卷入空氣。過小錐角使凝料脫模困難；還會使充模時流動阻力大，比表面增大，熱量損耗大。
2.5確定模腔數量及其排列方式、澆口形式。
燈罩外形尺寸不大，為了降低注射成本，根據所選注塑機的注射量，采用一模四型腔的模具，并選用平衡式十字排列。為了滿足較高的外觀要求，確定采用點澆口。型腔排列方式圖5，點澆口分流道拉料井結構形式圖6。
圖 3型腔排列
圖 4點澆口分流道拉料井結構形式
圖 4分流道截面圖
圖 3澆口套
2.6計算并校核型腔部分的強度和剛度，根據燈罩的高度確定型腔板的側壁厚度，型芯固定板的厚度。并確動模板、頂出桿，支塊厚度及其模具安裝方法。
2.7完成了對模具工作部分尺寸及公差進行設計計算。
2.8完成了部分模具零件結構設計。如：澆口套、定位圈等。
2.9完成裝配草圖，如圖7。
圖 5裝配圖
3.存在問題
3.1模具工作原理還是有一點不太了解。
3.2繪制裝配圖是發現設計中一些問題，后期要進行修改。
3.3三維軟件繪制模具有點欠缺。
4.后期工作安排
第9-13周：運用Pro/E或solidworks完成模具整體結構3D圖，完成模具零件的選材、工藝規程的編制、裝配圖及零件圖的 繪制等工作。
第14-15周：對所有圖紙進行校核，編寫設計說明書，所有資料提請指導教師檢查。
第16周：準備畢業答辯。
指導教師簽字：
年 月 日
注：1）正文：宋體小四號字，行距20磅，單面打?。黄渌袷揭笈c畢業論文相同。
2）中期報告由各系集中歸檔保存，不裝訂入冊。
題目：盒蓋連體零件注塑模具設計
系 別： 機電信息系
專 業： 機械設計制造及自動化
班 級：
學 生：
學 號：
指導老師：
2013年5月
盒蓋連體零件注塑模具設計
摘 要
從分析塑料零件注射模具設計的全過程，并從其加工工藝性出發，選取了較為合理的設計方案，經工藝計算并初步確定模具結構方案，最后進行模具各個部分零件的設計。由于本產品結構比較復雜，模具結構及制造工藝相對較為復雜，生產批量為大批量，精度為IT14，則成本會比較高。且模具采用的是一模兩腔的設計，所以增加了結構的復雜性，通過對抽芯機構的計算和設計，同時把握模具相關運動部件的設計，其中包括定位零件和成型零件尺寸的計算和校核。該模具采用了一次分型，使制件的主流道凝料和分流道凝料從模具的成型板中脫出，最后利用推桿推出作用，使制件脫離型芯，達到制件的生產。同時，本模具的亮點和難點在于有兩個帶角度的內側抽芯和其型芯型腔的加工復雜性上，但通過比較合理的斜頂裝置可以很完善的達到內抽的效果，并且該機構制造相對簡單，可降低模具成本。在一些零件的選用上也是盡量選取標準件以降低模具造價，型芯和型腔都采用鑲拼式的結構，同時運用直通式冷卻水道，降低加工難度和成本。最后分析模具裝配和型腔的加工工藝性。
關鍵詞：注塑模；分型面；抽芯
6
The Plastic Mold Design of Box Cover
Abstract
From the analysis of the whole process of the design of plastic pates injection mold, and departure from its processing technology, select a more reasonable design, the process calculation and initially identified the mold structure of the program, the final design of some parts of the mold. Due to the product structure is more complex, the mold structure and manufacturing process is relatively complex, production volume in bulk, the accuracy of IT10, the cost will be higher. The die is used to design a mold two cavity, so increases the complexity of the structure, calculation and design of the core-pulling mechanism, and grasp the mold moving parts design, including the calculation of the size of positioning parts and molded parts and checked. Spure slug and shunt used in the mold of the type, so that the parts of the slug of the mold forming board last putter introduced the roleof the parts off the core, to achieve the production of parts. At the same time, the highlight and difficulty of this mold is processing complexity two angled inside core-pulling and its core cavity, but more reasonable lifter device can be improved to achieve the pumping effect, and the organization to produce relatively simple, can reduce the cost of the mold. Also try to select in some parts of the slection of standard parts to reduce tooling cost, core and cavity mosaic structure, while the use of straight-through cooling water, reducing the processing difficulty and cost. Finally, analysis and processing of the mold assembly and cavity.
Keywords: Plastic injection molding；once；medial to the core-pulling
主要符號表
k
安全系數
E
材料彈性模量
Smax
塑料的最大收縮率
q
熔融塑料在模腔內的壓力
Smin
塑料的最小收縮率
V塑
塑件體積
P0
注射壓力
V注
注射機理論注射量
P公
公稱注射壓力
F鎖
鎖模力
Δs
塑件公差
δs
塑件收縮引起的塑件尺寸誤差
T
注射機的額定鎖模力
LS
塑件尺寸
L凹
型腔尺寸
L凸
型芯尺寸
H塑
塑件內形深度基本尺寸
S
注射機最大行程
d
塑件外徑基本尺寸
H
模具閉合尺寸
D
塑件內形基本尺寸
Hmin
模具最小尺寸
h
凸模/型芯高度尺寸
Hmax
模具最大尺寸
δ
模具制造公差
α
傾斜角
A
塑件包緊型芯的側面積
p
單位面積塑件對型芯的正力
F
塑件的投影面積
n
個數
P
型腔壓力
f
摩擦系數
φ
長度系數
Q
總脫模力
目 錄
摘 要 I
Abstract II
1 前言 1
1.1我國塑料模具的發展現狀 1
1.2塑料模具的發展趨勢 2
1.3中國塑料模具行業存在的問題 3
1.4發展展望 4
2 塑料ABS分析 6
2.1基本特性 6
2.2成型特性 6
2.3綜合性能 6
2.4ABS的注射工藝參數 7
3 塑料模的總體設計 8
3.1塑件的形狀尺寸 8
3.2型腔數目的決定及排布 8
3.3注射機的選擇 9
3.4分型面確定 9
3.5模架的選擇 10
3.5.1型腔壁厚的計算 10
3.5.2凹模型腔底部高度 11
3.5.3模架的選擇 11
4 成型尺寸及澆注系統設計 12
4.1型腔的內徑計算 12
4.2型腔的深度尺寸計算 12
4.3型芯的外徑計算 12
4.4型芯的高度計算 13
4.5澆注系統的初步計算 13
5 導柱導向機構的設計 15
5.1導柱導向機構的作用 15
5.2導柱導套的選擇 15
6 脫出機構設計 16
6.1推出機構的組成 16
6.2設計原則 16
6.3脫模力的計算 16
6.4推板脫出機構計算 17
6.5脫模機構設計 18
6.5.1簡單脫模 18
6.5.2側向抽芯機構設計 19
7 排氣溫控系統設計 22
7.1溫控系統設計 22
7.2注射模冷卻系統設計原則 22
7.3冷卻系統的結構設計 23
7.4 冷卻水孔直徑計算 24
7.5求冷卻水在水孔里的流速 24
8 注射機與模具型腔型芯強度校核 25
8.1注射機的校核 25
8.2型腔型芯的強度校核 25
9 模具的裝配、試模與維修 26
9.1模具的裝配 26
9.2模具裝配的主要內容 26
9.2.1型芯裝配 26
9.2.2型腔的裝配加工 26
9.2.3導柱、導套的裝配 26
9.2.4頂桿裝配加工 26
9.2.5澆口套的裝配加工 26
9.3裝配順序 27
9.4試模 27
9.5模具的維修 27
10 模具裝配圖 28
11 模具可行性分析 29
11.1本模具的特點 29
11.2市場效益及經濟效益分析 29
參考文獻 30
總結 31
致 謝 32
畢業設計（論文）知識產權聲明 33
畢業設計（論文）獨創性聲明 34
1 前言
1.1我國塑料模具的發展現狀
整體來看，中國塑料模具無論是在數量上，還是在質量、技術和能力等方面都有了很大進步，但與國民經濟發展的需求、世界先進水平相比，差距仍很大。一些大型、精密、復雜、長壽命的中高檔塑料模具每年仍需大量進口。在總量供不應求的同時，一些低檔塑料模具卻供過于求，市場競爭激烈，還有一些技術含量不太高的中檔塑料模具也有供過于求的趨勢[1]。
加入WTO，給塑料模具產業帶來了巨大的挑戰，同時帶來更多的機會。由于中國塑料模具以中低檔產品為主，產品價格優勢明顯，有些甚至只有國外產品價格的1/5~1/3，加入WTO后，國外同類產品對國內沖擊不大，而中國中低檔模具的出口量則加大；在高精模具方面，加入WTO前本來就主要依靠進口，加入WTO后，不僅為高精尖產品的進口帶來了更多的便利，同時還促使更多外資來中國建廠，帶來國外先進的模具技術和管理經驗，對培養中國的專業模具人才起到了推動作用。
畢業設計(論文)開題報告
題目：燈罩塑料模具設計
系 別 機電信息系
專 業 機械設計制造及自動化
班 級
姓 名
學 號
導 師
2012年12月18日
1、畢業設計（論文）題目背景、研究意義及國內外相關研究情況
1.1、課題名稱：燈罩塑料模具設計
1.2、課題研究背景和意義
1.2.1、德國人說模具工業是金屬加工業中之王，美國人說模具工業是美國工業的基石，羅馬尼亞人說模具就是黃金，而日本人說模具是促進社會繁榮富裕的動力，中國人說模具工是工業生產之母[1]。這充分說明模具工業是制造業中最重要的基礎性行業，又被經濟學家稱為“點鐵成金”的磁力工業[5]。模具是制造業的一種基本工藝裝備，它的作用是控制和限制材料（固態或液態）的流動，使之形成所需要的形體[7]。用模具制造零件其效率高，產品質量好，材料消耗低，生產成本低而廣泛應用于制造業中。模具工業既是高新技術產業的一個組成部分，又是高新技術產業化的重要領域。模具在機械，電子，輕工，汽車，紡織，航空，航天等工業領域里，日益成為使用最廣泛的主要工藝裝備，它承擔了這些工業領域中 60％～90％的產品的零件、組件和部件的生產加工（來自泊頭華林模具制造有限公司產品中心模具的重要性）。
1.2.2、模具種類有：沖模，鍛模，塑料模，壓鑄模，粉末冶金模，玻璃模，橡膠模，陶瓷模等。除部分沖模以外的的其他各種模具都屬于型腔模，因?yàn)樗麄円话愣际且揽咳S的模具型腔使材料成型[13]。本次畢業設計主要是塑料模，故其他模具不談。而塑料模具是大批生產塑料制品的現代化專用成型工藝裝備的總稱。而且塑料是繼陶瓷和金屬之后的第三大材料，廣泛應用在現代工業和日常生活中[8]。塑料模主要包括注射模，壓塑模，擠塑模，此外還有擠出成型模，泡沫塑料的發泡成型模，低發泡注射成型模，吹塑模等[1]。
1.2.3、我國模具技術的現狀及發展趨勢20世紀80年代開始，發達工業國家的模具工業已從機床工業中分離出來，并發展成為獨立的工業部門，其產值已超過機床工業的產值。改革開放以來，我國的模具工業發展也十分迅速。近10年來，每年都以 15％的增長速度快速發展。許多模具企業十分重視技術發展。加大了用于技術進步的投入力度，將技術進步作為企業發展的重要?jiǎng)恿2]。
2、本課題研究的主要內容、設計的要求、擬定方案和研究方法、手段
2.1、主要內容：塑件測繪圖、模具裝配圖、模具零件圖、說明書
2.2、本設計的基本要求：
2.2.1不少于3000字的文獻綜述；
2.2.2充分了解塑件結構，繪制3D圖，并完成基本參數的計算及注射機的選用；
2.2.3確定模具類型及結構，完成模具的結構草圖的繪制；
2.2.4運用Pro/E或solidworks等工具軟件輔助設計完成模具整體結構 ；
2.2.5對模具工作部分尺寸及公差進行設計計算；
2.2.6對模具典型零件需進行選材及熱處理工藝路線分析；
2.2.7編制模具中典型零件的制造工藝規程卡片；
2.2.8對設計方案和設計結果進行經濟分析和環保分析；
2.2.9繪制模具零件圖及裝配圖；
2.2.10對模具結構進行三維剖析，輸出模具開合結構圖；
2.2.11編寫設計說明書（所有3D圖插入說明書中恰當位置）。
2.3、擬定方案
2.3.1燈罩零件圖圖1。
圖1燈罩零件圖
圖3內部結構
圖2外形
2.3.2燈罩模型外形圖2，內部結構圖3。
2.3.3設計要求
課題名稱：燈罩塑料模具設計；材料選擇：PS；生產批量：大批量；精度要求：中；塑料等級：4級。
2.3.4方案擬定
方案1：選擇燈罩的下端面為分型面，采用整體式的直澆道，點澆口，澆口設在零件的上端面，選用臥式注射機，選用機動推出機構脫模，機動內側分型方式抽芯。
此方案生產效率高，操作簡便，動作可靠，方便脫出流道凝料。
方案2：選擇燈罩的如圖1剖切位置為分型面，采用整體式的直澆道，側澆口，澆口設在零件的側面，手動推出機構脫模，用手動內側分型方式抽芯。
此方案的優點是制造方便，但操作麻煩，生產率低，勞動強度大。
經過兩種方案的對比，方案1的可靠性高，經濟性價比高，適合大批量生產，故選此次模具設計選用方案1。
2.4、研究方法、手段：
本設計題目涉及目標均為工程實際零件，通過對塑件的實體測繪，完成基本參數的采集，然后運用《注塑模具設計》、《塑料模具設計》、《塑料成型工藝》等知識，指導學生利用AutoCAD和Pro/E或soildworks等軟件完成模具結構的設計，并進行相關的校核計算，完成包括選材熱處理、制造工藝規程、可行性分析等工作。本設計旨在鍛煉學生在專業技術應用能力上達到培養目標的基本要求，在塑料成型工藝與塑料模具設計技術方面得到全面提高，并受到模具設計工程師的基本訓練。
3、本課題研究的重點及難點，前期已開展工作
3.1、重點及難點:
本課題研究的重點是模具總體結構的設計優化選擇,應用相關軟件進行零件圖和裝配圖繪制,以及對模具結構進行三維剖析輸出開合模具結構圖.難點在于抽芯機構的設計和總體方案的優化選擇,以及模具三維結構剖析和開合模具圖輸出。
3.2、前期工作：
3.2.1查閱了相關專業資料為設計做好準備；
3.2.2完成模具二維圖、3D圖的繪制；
3.2.3進行了模具結構的簡單分析，擬訂了兩套簡單結構方案。
4、完成本課題的工作方案及進度計劃（按周次填寫）
第1周：熟悉課題，工廠參觀注塑生產過程，繪制塑件3D圖；
第2周：確定模具類型及結構，繪制模具結構草圖，準備開題答辯；
第3-8周：對模具工作部分尺寸及公差進行設計計算，并運用Pro/E或solidworks輔助設計完成部分模具零件，準備中期答辯, 翻譯外文資料；
第9-15周：運用Pro/E或solidworks完成模具整體結構3D圖，完成模具零件的選材、工藝規程的編制、裝配圖及零件圖的 繪制等工作；
第16周：對所有圖紙進行校核，編寫設計說明書，所有資料提請指導教師檢查，準備畢業答辯。
參考文獻
[1]鄒繼強 塑料制品及其成型模具設計 北京：清華大學出版社 2005.2
[2]屈偉平 國內模具行業發展現狀從在問題及對策 工程機械 廣西桂林 2006.4
[3]肖愛民 沈春根 塑料模具設計與制造完全自學手冊 北京：兵器工業出版社2006.10
[4]李秦蕊 塑料模具設計 西北工業大學出版社1988年修訂本
[5]師商 沈陽模具產業前景廣闊全力打造世界一流“工業之母“ 中國高新技術產業導報2009.11.23第 C05 版
[6]陳劍鶴 模具設計基礎 北京：機械工業出版社2003
[7]李秦蕊 塑料模具設計 西安：西北工業大學出版社2006
[8]張中元 塑料注射模具設計：入門到精通 北京：航空工業出版社1999.1
[9]方國治 高洋 童忠良塑料制品加工與應用實例 北京：化學工業出版社 2009.12
[10]申開智 塑料成型模具 北京：中國輕工業出版社2002
[11]徐政坤 塑料成型工藝與模具設計 北京：國防工業出版社2008
[12]陳萬林 實用模具技術 北京：機械工業出版社2000
[13]陳志剛 塑料模具設計 北京：機械工業出版社2002
[14 ]付偉 陳碧龍 注塑模具設計：原則、要點及實例解析 北京：機械工業出版社2010.7
[15]Eldukhri. E, E.Design and control of a biped walking robot.phD thesis.Department of Electronic and Electrical Engineering University of Salford UK.
[16]Mechanical Drive(Reference Issue). Machine Design.52(14),1980
[17]Yong-Sheng Ma Shu Beng Tor Graeme A. Britton The development of a standard component library for plastic injection mould design using an object-oriented approach July 2002
5 指導教師意見（對課題的深度、廣度及工作量的意見）
指導教師： 年 月 日
6 所在系審查意見：
系主管領導： 年 月 日
畢業設計(論文)外文資料翻譯
系 別： 機電信息系
專 業： 機械設計制造及其自動化專業
班 級：
姓 名：
學 號：
外文出處： 塑料注塑模具并行設計
21（2005）368-378
附 件： 1. 原文； 2. 譯文
2013年3月
塑料注塑模具并行設計
Assist.Prof.Dr. A. YAYLA /Prof.Dr. Pa? a YAYLA
摘要
塑料制品制造業近年迅速成長。其中最受歡迎的制作過程是注塑塑料零件。注塑模具的設計對產品質量和效率的產品加工非常重要。模具公司想保持競爭優勢,就必須縮短模具設計和制造的周期。
模具是工業的一個重要支持行業，在產品開發過程中作為一個重要產品設計師和制造商之間的聯系。產品開發經歷了從傳統的串行開發設計制造到有組織的并行設計和制造過程中,被認為是在非常早期的階段的設計。并行工程的概念(CE)不再是新的,但它仍然是適用于當今的相關環境。團隊合作精神、管理參與、總體設計過程和整合IT工具仍然是并行工程的本質。CE過程的應用設計的注射過程包括同時考慮塑件設計、模具設計和注塑成型機的選擇、生產調度和成本中盡快設計階段。
介紹了注射模具的基本結構設計。在該系統的基礎上,模具設計公司分析注塑模具設計過程。該注射模設計系統包括模具設計過程及模具知識管理。最后的原則概述了塑料注射模并行工程過程并對其原理應用到設計。
關鍵詞:塑料注射模設計、并行工程、計算機輔助工程、成型條件、塑料注塑、流動模擬
1、簡介
注塑模具總是昂貴的,不幸的是沒有模具就不可能生產模具制品。每一個模具制造商都有他/她自己的方法來設計模具,有許多不同的設計與建造模具。當然最關鍵的參數之一,要考慮到模具設計階段是大量的計算、注射的方法,澆注的的方法、研究注射成型機容量和特點。模具的成本、模具的質量和制件質量是分不開的
在針對今天的計算機輔助充型模擬軟件包能準確地預測任何部分充填模式環境中。這允許快速模擬實習,幫助找到模具的最佳位置。工程師可以在電腦上執行成型試驗前完成零件設計。工程師可以預測過程系統設計和加工窗口,并能獲得信息累積所帶來的影響,如部分過程變量影響性能、成本、外觀等。
2、注射成型法
注塑成型是最有效的方法之一,將塑料最好的一面呈現。這是普遍用于制造復雜的制件,優點是簡單、經濟、準確與少浪費。塑料零件的批量生產主要采用模具。產品設計制造過程包括模具的結構必須經過外觀評價和結構優化。當設計師創造注射模具組件時，他們面臨一個巨大的多種選擇，并行工程需要一個工程師考慮制產品在發展階段時的過程設計。一個好的產品設計為了滿足市場其制造過程是不可能太貴的。CAD/CAM整合了過程仿真、快速成形制造能減少風險,進一步提高產品開發的有效性。
3、注塑模具設計重要的計算機輔助
注射模具設計任務是相當復雜的。計算機輔助工程(CAE)分析工具提供了巨大的優勢讓設計工程師考慮幾乎所有模具、注塑參數沒有真正利用的地方。在可能性的設計、理念設計師，給工程師們機會去消除潛在的問題,開始真正的生產。此外,在虛擬環境中,設計師可以快速而方便地評估特定的成型參數敏感性的質量和生產最終產品。所有這些分析工具使所有模具設計將在一天甚至數小時完成,而不需要幾周或幾個月來做真正的實驗反復試驗。CAE用于早期設計的部分,模具和注塑模具參數、節約成本是實質功能不僅是最好的部分,而且還能節省和縮短開發產品推向市場的時間。
在所有方面的成型過程中需要滿足塑料部分設置的公差,包括零件的尺寸和形狀,樹脂的化學結構、填料使用,模具型腔布置、澆注、模具冷卻并釋放機制使用。面對這復雜性,設計師經常使用電腦設計工具,如有限元分析(FEA)和充型分析(MFA),減少開發時間和成本。有限元分析確定部分結構的應變、應力和撓度,在那里這些參數可以很好地被定義。沖型分析位置和大小進行優化樹脂流動。它還定義了焊縫的位置、面積過大的壓力,以及如何影響墻壁和肋厚度流動。其它有限元分析設計工具包括模具冷卻溫度分布,分析周期時間和收縮為空間控制和預測凍結應力、翹曲變形等情況。
采用CAE分析部分壓縮模如圖1所示。分析周期始于創造一個CAD模型和有限元網格的模具腔。在注入條件規定,充型、纖維取向、固化和熱歷史、收縮和翹曲變形等情況進行仿真。該材料的性能計算模型模擬可用于結構的行為的一部分。如果需要部分設計澆口位置及加工條件可以在電腦上修改,直到一個可接受的零件的表達式。摘要分析了一個優化完成部分可采用降低weldline(亦即也knitline),優化力量、控制溫度和固化、最小收縮和翹曲變形等情況。
模具加工的前身是手工制作,如檢查每一剪機床維修工。自動化的增長和普遍使用的電腦數值控制或CNC加工中心使這過程變得更加簡便。設計的時間也被大大降低通過使用特殊的軟件能夠產生刀具路徑直接從CAD數據文件提取。主軸速度高達100000每分鐘轉速提一步提出了高速加工。切削材料已經證明了驚人的表現而不使用任何的剪切/冷卻液,什么都沒有。作為一個結果,加工過程復雜的型心和型腔已經加快了。
這是一個好消息,產生一個模具所花費的時間不斷的被減少。壞消息是,另一方面,甚至所有這些進步、設計和制造的模具仍然要花很長時間,是非常昂貴的。
圖1的注射模CAE分析部分
許多公司的經理人現在體會部署新產品推向市場迅速發展是多么的重要。企業的繁榮關鍵在于新產品。他們推動企業的收入、市場份額、底線和股票價格。一個公司能夠發明優質的產品和合理的價格領先其競爭不僅實現了100%的打敗市場競爭對手的產品,但之前到達也傾向于保持主導地位甚至幾年之后終于宣布競爭產品(史密斯,1991)。對大多數產品來說,這兩個優勢是戲劇性的。現在產品快速發展的一個關鍵方面的競爭成功。圖2顯示,只有3 - 7%的產品結構與一般的工業或電子公司是小于5歲。公司在第一四分位,這個數字增加到15 - 25%。一流的公司,它是60 - 80%(湯普森,1996)。最好的公司在不斷開發新產品。在惠普,超過80%的利潤結果從產品小于2歲!(Neel,1997)
圖2重要的新產品(雅克布,2000)
以先進的計算機技術和人工智能,努力已經被指向降低成本和交貨時間在設計和制造注塑模具。注塑模具設計主要感興趣的地區,因?yàn)樗且粋€(gè)復雜的過程涉及到很多表面設計等各零件的模具,每個都需要專家的知識和經驗。李et.艾爾。(1997)提出了一種系統的方法關于注塑模具設計的知識庫和并行工程環境。
4并行工程在模具設計中
并行工程(CE)是一個系統性的方法來集成產品開發過程。它代表了團隊合作的價值觀、信任和分享,以這樣的方式,決策是通過協商一致,包括視角并聯,從一開始就產品的整個生命周期(埃文斯,1998)。從本質上講,CE提供合作、合作、集體和同步工程的工作環境。一個并行工程的方法是基于五個關鍵要素:
1、過程
2、多學科小組
3、綜合設計模型
4、設施
5、軟件基礎設施
圖3的方法對塑料注射模設計,工程b)串并行工程
在塑料模具制造業、CE是很重要的,由于高成本加工和長交貨期。通常,CE利用制造原型模具在設計之初相位分析和調整設計。生產制造模具是作為最后一步。制造過程,包括模具的結構必須經過外觀評價和結構優化的產品設計。CE要求工程師考慮生產過程中產品設計的發展階段。一個好的設計產品是滿足市場如果其制造過程是不可能的。CAD/CAM整合過程模擬、快速成形制造能減少風險,從效率和進一步提高產品開發的有效性。
多年來,設計師已經被限制在他們可以產出通常必須設計制造(DFM)——那就是,調整他們的設計意圖,使元件(或總成)生產使用一個特定的進程或程序。此外,如果一個模具用于產生一個項目,而因此自動設計對固有限制在一開始就相處得很好。以注塑為例,以處理一個組件成功,即使在最小程度上,下面的設計元素需要考慮的內容:
1、.幾何
.拔模斜度
.非內角形狀
.近恒壁厚
.復雜性
.分裂線位置
.表面拋光
材料選擇
元件的合理化(減少組件)
成本
在注塑、生產的模具生產注射模具元件通常是最長的部分產品開發過程。當利用快速造型、CAD需要長時間,因此成為瓶頸。
廢水處理工程的工藝設計和注塑塑料涉及相當復雜且耗時的活動,包括零件設計、模具設計、注塑成型機的選擇、生產排程、工裝和成本估算。所有這些活動是傳統上由部分設計和模具制作人員按注射模順序的方式完成后塑料部件的設計。很明顯的,這些序列階段可能會導致長的產品開發時間。但隨著社會的過程中實施并行工程所有參數影響產品設計、模具設計、機械的選擇、生產排程、模具和加工成本被認為是盡早塑料部件的設計。
使用時有效,CAE方法節省了部分設計及制造巨大的成本和時間。這些工具幾乎讓工程師測試部分處理它在其正常使用壽命表現怎樣。材料供應商,設計師和制造商應該運用這些工具同時在設計之初階段利用CAE增加塑料成本效益。CAE技術使人們有可能取代傳統,順序決策程序和并行設計過程,其中各方之間是如何產生互動和分享信息,圖3塑料注塑、CAE及相關設計數據提供一個綜合的環境,為便于并行工程的設計、制造和模具部分,以及材料的選擇和模擬優化工藝控制參數。
定性費用有關的部分比較設計上的變化被顯示在圖4，顯示出一個事實,那就是當設計已經改好了在早期階段在計算機屏幕上時,與成本有關的順序的10.000倍,如果低于部分生產。這些改變可能發生在塑料部件模具的改變,如澆口位置、厚度變化、生產延遲,質量成本、機械安裝時間,或是設計變更在塑料部件。
圖4的成本在部分改變?cè)O(shè)計產品開發周期(張志剛,2001年版)
在早期設計階段,設計師設計模具部分必須完成零件設計基于各自的經驗相似的部分。但是隨著部分變得更為復雜,它變得相當困難的加工性能預測及部分不使用計算機輔助工具。因此,即使是相對復雜的部分,使用計算機輔助工具,防止變化和昂貴的設計過程中出現的問題,可以注射后。為成功實施并行工程,必須有歸屬感從人人參與。
5個案研究
圖5顯示初始CAD(計算機輔助設計)塑料部分用于噴灌消防栓的腿。一個基本特征,部分的部分保持平注射后,在注射操作原因變形問題。
另一個重要特點的塑料部件必須是一種高效的抗彎剛度。一批料中加入了不同取向的部分如圖5 b。這些應設計成一種方式,它有貢獻的重量最小部分的,而且是可行的。
在模具的設計流程,分析了塑料部分進行了模具仿真分析軟件讓選拔的最佳澆口位置圖6。這個數字表明最好的點澆口位置的中間饋線的中心部分。作為失真和陶瓷注射后的部分,至關重要的是,從功能的角度,它必須被保持在最低水平,同樣也使用軟件里面分析。圖5 b顯示結果暗示了事實后殘留在陶瓷注射預定義的尺寸公差。
6總結
在塑料注塑、CAD模型所得的塑料部分商業的3 D程序可用于部分性能和注塑工藝分析。借助于CEA技術和并行工程方法的使用,不僅注塑模具的設計和制造可以在很短的一段時間完成,而且它可能在開始時的模具設計把出現的所有潛在的問題從部分設計、模具設計和工藝參數消除。這兩個工具幫助設計師和模具制造商生產良好的產品,更好的交付和更快的模具用較少的時間和金錢。
【原文一】
CONCURRENT DESIGN OF PLASTICS INJECTION MOULDS
Assist.Prof.Dr. A. YAYLA /Prof.Dr. Pa? a YAYLA
Abstract
The plastic product manufacturing industry has been growing rapidly in recent years. One of the most popular processes for making plastic parts is injection moulding. The design of injection mould is critically important to product quality and efficient product processing. Mould-making companies, who wish to maintain the competitive edge, desire to shorten both design and manufacturing leading times of the by applying a systematic mould design process.
The mould industry is an important support industry during the product development process, serving as an important link between the product designer and manufacturer. Product development has changed from the traditional serial process of design, followed by manufacture, to a more organized concurrent process where design and manufacture are considered at a very early stage of design. The concept of concurrent engineering (CE) is no longer new and yet it is still applicable and relevant in today’s manuf acturing environment. Team working spirit, management involvement, total design process and integration of IT tools are still the essence of CE. The application of The CE process to the design of an injection process involves the simultaneous consideration of plastic part design, mould design and injection moulding machine selection, production scheduling and cost as early as possible in the design stage.
This paper presents the basic structure of an injection mould design. The basis of this system arises from an analysis of the injection mould design process for mould design companies. This injection mould design system covers both the mould design process and mould knowledge management. Finally the principle of concurrent engineering process is outlined and then its principle is applied to the design of a plastic injection mould.
Keywords :Plastic injection mould design, Concurrent engineering, Computer aided engineering, Moulding conditions, Plastic injection moulding, Flow simulation
1. Introduction
Injection moulds are always expensive to make, unfortunately without a mould it can not be possible ho have a moulded product. Every mould maker has his/her own approach to design a mould and there are many different ways of designing and building a mould. Surely one of the most critical parameters to be considered in the design stage of the mould is the number of cavities, methods of injection, types of runners, methods of gating, methods of ejection, capacity and features of the injection moulding machines. Mould cost, mould quality and cost of mould product are inseparable
In today’s completive environment, computer aided mould filling simulation packages can accurately predict the fill patterns of any part. This allows for quick simulations of gate placements and helps finding the optimal location. Engineers can perform moulding trials on the computer before the part design is completed. Process engineers can systematically predict a design and process window, and can obtain information about the cumulative effect of the process variables that influence part performance, cost, and appearance.
2. Injection Moulding
Injection moulding is one of the most effective ways to bring out the best in plastics. It is universally used to make complex, finished parts, often in a single step, economically, precisely and with little waste. Mass production of plastic parts mostly utilizes moulds. The manufacturing process and involving moulds must be designed after passing through the appearance evaluation and the structure optimization of the product design. Designers face a huge number of options when they create injection-moulded components. Concurrent engineering requires an engineer to consider the manufacturing process of the designed product in the development phase. A good design of the product is unable to go to the market if its manufacturing process is impossible or too expensive. Integration of process simulation, rapid prototyping and manufacturing can reduce the risk associated with moving from CAD to CAM and further enhance the validity of the product development.
3. Importance of Computer Aided Injection Mould Design
The injection moulding design task can be highly complex. Computer Aided Engineering (CAE) analysis tools provide enormous advantages of enabling design engineers to consider virtually and part, mould and injection parameters without the real use of any manufacturing and time. The possibility of trying alternative designs or concepts on the computer screen gives the engineers the opportunity to eliminate potential problems before beginning the real production. Moreover, in virtual environment, designers can quickly and easily asses the sensitivity of specific moulding parameters on the quality and manufacturability of the final product. All theseCAE tools enable all these analysis to be completed in a meter of days or even hours, rather than weeks or months needed for the real experimental trial and error cycles. As CAE is used in the early design of part, mould and moulding parameters, the cost savings are substantial not only because of best functioning part and time savings but also the shortens the time needed to launch the product to the market.
The need to meet set tolerances of plastic part ties in to all aspects of the moulding process, including part size and shape, resin chemical structure, the fillers used, mould cavity layout, gating, mould cooling and the release mechanisms used. Given this complexity, designers often use computer design tools, such as finite element analysis (FEA) and mould filling analysis (MFA), to reduce development time and cost. FEA determines strain, stress and deflection in a part by dividing the structure into small elements where these parameters can be well defined. MFA evaluates gate position and size to optimize resin flow. It also defines placement of weld lines, areas of excessive stress, and how wall and rib thickness affect flow. Other finite element design tools include mould cooling analysis for temperature distribution, and cycle time and shrinkage analysis for dimensional control and prediction of frozen stress and warpage.
The CAE analysis of compression moulded parts is shown in Figure 1. The analysis cycle starts with the creation of a CAD model and a finite element mesh of the mould cavity. After the injection conditions are specified, mould filling, fiber orientation, curing and thermal history, shrinkage and warpage can be simulated. The material properties calculated by the simulation can be used to model the structural behaviour of the part. If required, part design, gate location and processing conditions can be modified in the computer until an acceptable part is obtained. After the analysis is finished an optimized part can be produced with reduced weldline (known also knitline), optimized strength, controlled temperatures and curing, minimized shrinkage and warpage.
Machining of the moulds was formerly done manually, with a toolmaker checking each cut. This process became more automated with the growth and widespread use of computer numerically controlled or CNC machining centres. Setup time has also been significantly reduced through the use of special software capable of generating cutter paths directly from a CAD data file. Spindle speeds as high as 100,000 rpm provide further advances in high speed machining. Cutting materials have demonstrated phenomenal performance without the use of any cutting/coolant fluid whatsoever. As a result, the process of machining complex cores and cavities has been accelerated.
It is good news that the time it takes to generate a mould is constantly being reduced. The bad news, on the other hand, is that even with all these advances, designing and manufacturing of the mould can still take a long time and can be extremely expensive.
Figure 1 CAE analysis of injection moulded parts
Many company executives now realize how vital it is to deploy new products to market rapidly. New products are the key to corporate prosperity. They drive corporate revenues, market shares, bottom lines and share prices. A company able to launch good quality products with reasonable prices ahead of their competition not only realizes 100% of the market before rival products arrive but also tends to maintain a dominant position for a few years even after competitive products have finally been announced (Smith, 1991). For most products, these two advantages are dramatic. Rapid product development is now a key aspect of competitive success. Figure 2 shows that only 3–7% of the product mix from the average industrial or electronics company is less than 5 years old. For companies in the top quartile, the number increases to 15–25%. For world-class firms, it is 60–80% (Thompson, 1996). The best companies continuously develop new products. At Hewlett-Packard, over 80% of the profits result from products less than 2 years old! (Neel, 1997)
Figure 2. Importance of new product (Jacobs, 2000)
With the advances in computer technology and artificial intelligence, efforts have been directed to reduce the cost and lead time in the design and manufacture of an injection mould. Injection mould design has been the main area of interest since it is a complex process involving several sub-designs related to various components of the mould, each requiring expert knowledge and experience. Lee et. al. (1997) proposed a systematic methodology and knowledge base for injection mould design in a concurrent engineering environment.
4. Concurrent Engineering in Mould Design
Concurrent Engineering (CE) is a systematic approach to integrated product development process. It represents team values of co-operation, trust and sharing in such a manner that decision making is by consensus, involving all per spectives in parallel, from the very beginning of the product life-cycle (Evans, 1998). Essentially, CE provides a collaborative, co-operative, collective and simultaneous engineering working environment. A concurrent engineering approach is based on five key elements:
1. process
2. multidisciplinary team
3. integrated design model
4. facility
5. software infrastructure
Figure 3 Methodologies in plastic injection mould design, a) Serial engineering b) Concurrent engineering
In the plastics and mould industry, CE is very important due to the high cost tooling and long lead times. Typically, CE is utilized by manufacturing prototype tooling early in the design phase to analyze and adjust the design. Production tooling is manufactured as the final step. The manufacturing process and involving moulds must be designed after passing through the appearance evaluation and the structure optimization of the product design. CE requires an engineer to consider the manufacturing process of the designed product in the development phase. A good design of the product is unable to go to the market if its manufacturing process is impossible. Integration of process simulation and rapid prototyping and manufacturing can reduce the risk associated with moving from CAD to CAM and further enhance the validity of the product development.
For years, designers have been restricted in what they can produce as they generally have to design for manufacture (DFM) – that is, adjust their design intent to enable the component (or assembly) to be manufactured using a particular process or processes. In addition, if a mould is used to produce an item, there are therefore automatically inherent restrictions to the design imposed at the very beginning. Taking injection moulding as an example, in order to process a component successfully, at a minimum, the following design elements need to be taken into account:
1. . geometry;
. draft angles,
. Non re-entrants shapes,
. near constant wall thickness,
. complexity,
. split line location, and
. surface finish,
2. material choice;
3. rationalisation of components (reducing assemblies);
4. cost.
In injection moulding, the manufacture of the mould to produce the injection-moulded components is usually the longest part of the product development process. When utilising rapid modelling, the CAD takes the longer time and therefore becomes the bottleneck.
The process design and injection moulding of plastics involves rather complicated and time consuming activities including part design, mould design, injection moulding machine selection, production scheduling, tooling and cost estimation. Traditionally all these activities are done by part designers and mould making personnel in a sequential manner after completing injection moulded plastic part design. Obviously these sequential stages could lead to long product development time. However with the implementation of concurrent engineering process in the all parameters effecting product design, mould design, machine selection, production scheduling, tooling and processing cost are considered as early as possible in the design of the plastic part.
When used effectively, CAE methods provide enormous cost and time savings for the part design and manufacturing. These tools allow engineers to virtually test how the part will be processed and how it performs during its normal operating life. The material supplier, designer, moulder and manufacturer should apply these tools concurrently early in the design stage of the plastic parts in order to exploit the cost benefit of CAE. CAE makes it possible to replace traditional, sequential decision-making procedures with a concurrent design process, in which all parties can interact and share information, Figure 3. For plastic injection moulding, CAE and related design data provide an integrated environment that facilitates concurrent engineering for the design and manufacture of the part and mould, as well as material selection and simulation of optimal process control parameters.
Qualitative expense comparison associated with the part design changes is shown in Figure 4 , showing the fact that when design changes are done at an early stages on the computer screen, the cost associated with is an order of 10.000 times lower than that if the part is in production. These modifications in plastic parts could arise fr om mould modifications, such as gate location, thickness changes, production delays, quality costs, machine setup times, or design change in plastic parts.
Figure 4 Cost of design changes during part product development cycle (Rios et.al, 2001)
At the early design stage, part designers and moulders have to finalise part design based on their experiences with similar parts. However as the parts become more complex, it gets rather difficult to predict processing and part performance without the use of CAE tools. Thus for even relatively complex parts, the use of CAE tools to prevent the late and expe