鎂合金筆記本電腦外殼沖壓模具設計-復合模含12張CAD圖,鎂合金,筆記本電腦,外殼,沖壓,模具設計,復合,12,十二,cad 鎂合金筆記本電腦外殼沖壓模具設計 摘 要 分析了筆記本電腦外殼的沖壓工藝，設計了一套用于液壓機上的結構簡單的成形模。本文從產品的結構和功能出發，介紹了各沖壓工序的模具結構及工作過程。提出了模具設計及制造時應注意的事項。分析鎂合金AZ31的性能，存在常溫下不可拉深的問題，通過對零件進行詳盡的分析和查閱相關技術資料，設計了在拉深過程中對模具和零件進行加熱的拉深模，這樣就很容易的解決了上述問題。該產品要在兩個方向進行切邊，通過對產品進行工藝分析，如果設計成兩個方向同時進行切邊的復合模，則很難保證零件切邊部分的精度，所以分水平切邊和垂直切邊為兩個單獨的工序進行，從而滿足產品的技術要求。 關鍵詞：筆記本電腦外殼，沖壓工藝，拉伸模，修邊模 Design of the Stamping Die for the Magnesium AZ31 Outer Shell of the Notebook PC Author: Bo Fengxia Tutor : Huang Changing Abstract The stamping process for the outer shell of the notebook PC is analyzed and a set of simply constructed forming die used on liquid-press was designed. The article introduces the structure and working process of the die on each operation from the structure and the function of the product. And the points for attention in the design and manufacture of the dies are listed. The efficiency of magnesium AZ31 is analyzed in sheet metal forming and that it can’t draw in normal temperature. The problem is resolved by heating the die and workpiece during drawing, after detailed analyzing and relative technical data consulting. The product has to be trimmed in two directions. After analyzing the technic of the product, we know: If the two directions are carried out at one time, it is hard to make sure the precision. On the contrary, if we make one direction at one time, it is easy to satisfy the technical requirement of the product. Key words: the outer shell of the notebook PC, stamping process, drawing die, trimming die 目 錄 1 緒論……………………………….…………………………………………….…1 1.1 選題背景及目的…………………………………….……..…………………1 1.2 國內外研究狀況…………………………………….………………………..1 1.3 課題研究方法………………………………….……………………………..2 1.4 論文構成………………………………….…………...……………………...2 2 沖壓工藝規程的編制 ………………………………….……………………..3 2.1 沖壓件的工藝分析 …………………………………………………………3 2.1.1 材料 ………………………………………………………………….4 2.1.2 結構工藝性分析 ……………………………………………………5 2.2 毛坯形狀、尺寸的確定 ……………………………………………………6 2.2.1 盒形件的修邊余量 ………………………………….………………6 2.2.2 盒形件毛坯尺寸計算 ……………………………………………….7 2.3 排樣設計及材料利用率計算 ……….………………………………….…..8 2.3.1 排樣方式 ……………….………………….………………………...8 2.3.2 材料利用率計算 ……….…………………………………………...9 2.4 確定工藝方案 ……………………………………………………………….9 2.4.1基本工序的確定 ………………………………….…………………9 2.4.2不同工藝方案的比較 ……………………………………………….9 2.5 工藝計算 ……………………………………………………………………10 2.5.1 落料工序 …………………………………………………………...10 2.5.2 拉深工序 …………………………………………………………...11 2.5.3 沖孔工序 ……………………………………………………………12 2.5.4 修邊工序 ……………………………………………………………13 2.6 沖壓工藝過程卡片 ………………………………………………………...14 3 拉深模設計 ……………………………………….…………………………..17 3.1 模具的結構形式 ……………………………………….………………….17 3.2 模具刃口尺寸計算 …………………………………….…………………18 3.2.1 上下模刃口尺寸計算 …………………….……………………….18 3.2.2 壓力中心計算 ……………………………………………………..19 3.3 零件設計及標準件選擇 …………………………………………………..19 3.3.1 凸模的設計 …………………………..……………………………19 3.3.2 凹模的設計…………………………………..….………………….21 3.3.3 定位板的計 ………………………………...……………………...21 3.3.4 彈性壓圈的設計 …………………………...………………………21 3.3.5 拉深筋的設計……………………………………………………….22 3.3.6 上下模座、導柱導套的設計 …………………….……………….22 3.3.7 出件裝置的設計 …………………………………………………..22 3.4 模具閉合高度的計算 ……………………………………………………...23 3.5 繪制裝配圖及零件圖 ……………………………….……………………..23 3.6 壓力機校核 ………………………………………….……………………..23 4 修邊模設計 ……………………………………….…………………………...24 4.1 模具的結構形式 ………………………………………..…………………24 4.2 壓力中心計算 …………………………………….……………………….25 4.3 零件設計及標準件選擇…………………………….………………………25 4.3.1 斜楔和滑塊的設計 ………………………………………………..25 4.3.2 滑塊返回行程的復位機構 ………………….…………………….27 4.3.3 出件裝置的設計 ……………………………….…………………..27 4.3.4 上模座的設計 ……………………………………………………...28 4.3.5 下模座的設計 ………………………………………………………28 4.3.6 壓料板的設計 ………………………………………………………28 4.3.7 防磨板的設計 …………………………….….…………………….29 4.3.8 導板的設計 ………………………………….………………………29 4.4 模具閉合高度的計算 …………………………………………………….…29 4.5 裝配圖及零件圖的繪制 ………………………………………………….….30 4.6 壓力機校核 …………………………………………………………………..30 設計總結 …………………………………………………………………………31 致謝 ………………………………………………………………………………32 參考文獻 …………………………………………………………………………33