喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:414951605 或 1304139763】

摘要 船用廢氣燃燒臂是一種用于排放輪船尾氣的一套裝備,其中燃燒臂為懸臂結構.在現有的燃燒臂過程中,一般采用船用吊機的設計方法所設計的結構過于保守,使得結構質量偏大.燃燒臂結構安全系數會過大,不僅導致材料浪費和成本增加,而且還會對整個船體的穩定性不利.回面燃燒臂結構需要進行專門的設計.本文燃燒臂底座采用了專門用于回轉的回轉支承. 回轉支承裝置是近30年來發展起來的新型機器部件,它已從用子挖掘機和起重仇逐漸發展到用于其它機械。 回轉支承裝置近乎特大型的滾動軸承。它將機器的上部和下部連接起來，用以支承上部的重量和工作負荷，并使上部能相對于下部旋轉。本文對燃燒臂底座進行了彎曲強度,剪切強度及抗擠壓強度的校核. 而其燃燒臂上部桁架機構的設計比一般船用吊機要輕巧得多,對此燃燒臂結構需要進行單獨的強度計算. 由于所要設計的燃燒臂回轉速度僅為1/6(r/min),因此,為了考慮其使用效率只使用一個圓錐-圓柱減速度器,故,在此次設計中選用了直接帶減速裝置的凸緣安裝型式電動機,此電動機不僅功率和輸出轉矩能滿足要求,而且其輸出轉速僅為25n/min. 在回轉速度低,功率大的燃燒臂裝置中,所要求的減速器軸需要很高的強度,因此通過參考一些比較權威的機械設計手冊之后,再通過強度校核,選用減速器的軸材料為20CrMn. 關鍵詞：回轉支承，圓錐-圓柱減速度器， Abstract Marine from a burning arm for the tail gas emissions set of vessels and equipment, including combustion for the cantilever arm structure. Arm of the existing combustion process, the general marine crane designed by the design of the structure was too conservative, making the quality of the structure Too large. Combustion arm structural safety factor would be too large, not only lead to waste and material cost increases, but also the stability of the entire hull negative. Back-burner arm of the need for specialized design. Combustion arm base paper used a special use Rotary in the rotary bearing. Rotary support device is nearly 30 years ago to develop a new type of machine components, it has been used excavator and the lifting of hatred to the progressive development of other machinery for. Rotary supporting device near the large rolling bearings. The machine will link the upper and lower to the upper bearing the weight and work load, and the upper to the lower part of the rotation. In this paper, the base of a burning arm bending strength, shear strength and the strength of anti-extrusion check. Combustion arm of the Department and its agencies truss design than the general marine hanging confidential lightweight much, this burning need for a separate arm of the Strength calculation. Because the design of the combustion rotary arm speed is only 1 / 6 (r / min), therefore, in order to consider only the use of its efficiency in the use of a cone - cylindrical cut speed, so that in this design selected directly with the slowdown in device Flange installation type motor, the motor not only power and torque output to meet demand, but its output speed is only 25 n / min. Rotary in the low-speed, large power plant burning arm, the required reducer axis need a high intensity, some of the more authoritative reference by the mechanical design manual, to check through strength, the choice of reducer shaft material for 20 CrMn . Key words: slewing bearings, cone - cylindrical cut speed,