對輥形煤成型機設計,對輥形煤成型機設計,對于,輥形煤,成型,設計 山西農業大學 工程技術學院 畢業設計說明書（論文） 題目：對輥形煤成型機 作者：尹應祿 學號：31號 專業： 機 械 設 計 制 造 及 其 自 動 化 班級： 機制信052班 指導者： 張文煥 教授 評閱者： 2009-6山西 太谷 學士學位論文（設計）原創性聲明 本人鄭重聲明：所提交的學位論文，是本人在導師指導下，獨立進行研究工作所取得的成果。除文中已注明引用的內容外，本論文不包含任何其他個人或集體已經發表或撰寫過的作品成果。對本文研究做出過重要貢獻的個人和集體，均已在文中以明確方式標明。 本人完全意識到本聲明的法律后果由本人承擔。 學位論文作者簽名（親筆）： 年 月 日 ----------------------------------------------------------------------------------------- 學士學位論文（設計）版權使用授權書 專業： 論文（設計）題目： 本學位論文作者完全了解學校有關保留、使用學位論文的規定，本科生在校攻讀期間學位論文（設計）工作的知識產權單位屬山西農業大學，同意學校保留并向國家有關部門或機構送交論文的復印件和電子版，允許論文被查閱和借閱；本人授權山西農業大學可以將學位論文的全部或部分內容編入有關數據庫進行檢索，可以采用影印、縮印或掃描等復制手段保存、匯編學位論文。 畢業后發表與本研究有關的文章，作者單位署名應為“山西農業大學”，可以在備注中注明本人現工作單位。本研究成果的知識產權歸屬山西農業大學，未經指導教師和山西農業大學同意。本人不私自從事與課題有關的任何開發和盈利性活動。 學位論文作者簽名（親筆）： 年 月 日 導師簽名（親筆）： 年 月 日 畢業設計說明書中文摘要 對輥形煤成型機 摘 要 工業型煤是一種清潔、高效的新型燃料,廣泛應用于電力、冶金、鑄造、化肥等工業領域。目前我國工業型煤的生產工藝主要采用粉煤添加粘結劑和一些輔料低壓成型,以往的研究主要集中在成型工藝和粘結劑方面,對成型機械的研究開發甚少。事實上,成型機械是型煤生產的關鍵設備, 本文描述的是一種中高壓對輥成型設備的設計與實現。 成型力是由液壓系統提供，可以產生很高的成型壓力。而且有液壓的防止過載功能。提高了型煤的質量還能有效保護機器，不受意外傷害。 煤要成型就要有準確的對中性，該傳動系統采用同步齒輪箱，而且采用帳套連接技術可以進行少量的無級調節，保證有良好的同步對中性，提高了機器的運轉精度和型煤率。 采用變頻調速螺旋加料裝置。使送料連續，還有一定的預壓力。變頻調速可以根據產量,可以靈活地調整加料螺旋的旋轉速度,以滿足對輥成型機對加料速度、加料壓力及物料密度的匹配要求,提高了工業型煤的成球強度 機架采用螺栓拉緊，不但使得制作簡便、拆裝方便,而且機架的承載能力也強,滿足對輥成型機的工作要求。 關鍵詞 成型機 對輥 同步減速機 畢業設計說明書外文摘要 ABSTRACT Industrial briquette is a clean, efficient new fuel, widely used in the electricity, metallurgy, casting, chemical fertilizers and other industrial fields. At present, China's industrial briquette production techniques used mainly coal binder and add some excipients low pressure molding, Previous studies focused mainly on forming processes and binder, the right molding machinery little research and development. In fact, molding machinery is briquette production of key equipment. This paper describes a high-pressure China to roll molding equipment design and implementation Forming power of hydraulic systems can produce high pressure molding. But also to prevent the hydraulic overload functions. Improve the quality of coal can effectively protect machines from accidents. Coal will be forming an accurate pair of neutral, the use of synchronous transmission gearbox, Zhang Tao and using technology for linking a small number of no-regulation, to ensure a good synchronization of the neutral, improve the functioning of the machine precision and briquette rate. Using variable frequency spiral feeder. Feeding enable continuous, there will be some pressure on the advance. VVVF can output and the flexibility to adjust the feed screw rotation speed, to meet the roll forming machine for the feeding rate, feed pressure and density of materials matching requirements, enhance industrial briquette ball into strength Rack with bolt taut, not only makes the production of simple and easily reassembled, and the rack-bearing capacity, meet the roll forming machine and job requirements. Keywords Molding Machine Roller Synchronous Reducer 山西農業大學工程技術學院畢業設計說明書 目 錄 1 引言 1 1.1 工業型煤的發展現狀 1 1.2 型煤機械在工業型煤技術中的作用。 2 2. 電動機的選擇與整體傳動的確定 3 2.1 電動機的選擇： 3 2.2 傳動比的計算和分配 4 2.3 計算各級軸的參數 5 3. V帶的設計計算 7 3.1 確定計算功率 7 3.2 選擇帶型 7 3.3 確定帶輪直徑 7 3.4 驗算帶速 7 3.5 初定中心距 8 3.6 確定基準長度 8 3.7 計算實際中心距 8 3.8 驗算小帶輪包角 8 3.9 確定V帶的根數 8 3.10 確定單根V帶預緊拉力 9 3.11 作用在軸上的力 9 4 設計計算減速機齒輪 10 4.1 第一對齒輪設計計算 10 4.2 第二對齒輪設計計算 14 4.3 第三對齒輪設計計算 18 4.4 第四對齒輪設計計算 22 5. 減速機內軸的計算 26 5.1 Ⅰ號軸的設計計算 26 5.1.1 初步確定軸的最小直徑 26 5.1.2 軸的結構設計和軸上零部件的選擇 26 5.1.3 軸的強度校核 27 5.2 Ⅱ號軸的設計計算 28 5.2.1 初步確定軸的最小直徑 28 5.2.2 軸的結構設計和軸上零部件的選擇 28 5.2.3 Ⅱ號軸的強度校核 29 5.3 Ⅲ號軸的設計計算 30 5.3.1 初步確定軸的最小直徑 30 5.3.2 軸的結構設計和軸上零部件的選擇 30 5.3.3 Ⅲ號軸的強度校核 31 5.4 Ⅳ號軸的設計計算 32 5.4.1 初步確定軸的最小直徑 32 5.4.2 軸的結構設計和軸上零部件的選擇 32 5.4.3 Ⅳ號軸的強度校核 33 5.5 Ⅴ號軸的設計計算 34 5.5.1 初步確定軸的最小直徑 34 5.5.2 軸的結構設計和軸上零部件的選擇 34 5.5.3 Ⅴ號軸的強度校核 35 5.6 Ⅵ號軸的設計計算 36 5.6.1 初步確定軸的最小直徑 36 5.6.2 軸的結構設計和軸上零部件的選擇 36 5.6.3 Ⅵ號軸的強度校核 37 6. 軸承的校核 39 6.1 Ⅰ 軸軸承的校核 39 6.1.1 計算軸承支反力 合成支反力 39 6.1.2 軸承的派生軸向力 39 6.1.3 軸承所受的軸向載荷 39 6.1.4 軸承的當量動載荷 39 6.1.5 軸承壽命 40 6.2 Ⅱ軸軸承的校核 40 6.2.1 計算軸承支反力 40 6.2.2 軸承的派生軸向力 40 6.2.3 軸承所受的軸向載荷 40 6.2.4 軸承的當量動載荷 41 6.2.5 軸承壽命 41 6.3 Ⅲ軸軸承的校核 41 6.3.1 計算軸承支反力 41 6.3.2 軸承的派生軸向力 42 6.3.3 軸承所受的軸向載荷 42 6.3.4 軸承的當量動載荷 42 6.3.5 軸承壽命 42 6.4 Ⅳ軸軸承的校核 43 6.4.1 計算軸承支反力 43 6.4.2 軸承的派生軸向力 43 6.4.3 軸承所受的軸向載荷 43 6.4.4 軸承的當量動載荷 43 6.4.5 軸承壽命 44 6.5 Ⅴ軸軸承的校核 44 6.5.1 計算軸承支反力 44 6.5.2 軸承的派生軸向力 44 6.5.3 軸承所受的軸向載荷 45 6.5.4 軸承的當量動載荷 45 6.5.5 軸承壽命 45 7. 減速器鍵的校核 46 7.1 Ⅰ 軸鍵的校核 46 7.2 Ⅱ軸健的校核 46 7.3 Ⅲ軸健的校核 46 7.4 Ⅳ軸健的校核 47 7.5 Ⅴ軸健的校核 47 8. 減速器箱體及附件設計計算 48 8.1 箱體設計 48 結 論 49 參考文獻 50 致 謝 51 英文原文 Self-advancing hydraulic powered support Modern longwall mining employs hydraulic powered supports at the face area. The supports not only holds up the roof, pushes the face chain conveyor, and advances itself, but also provides a safe environment for all associated mining activities. Therefore its successful selection and application are the prerequisite for successful longwall mining. Furthermore, due to the large number of units required, the capital invested for the power support usually accounts for more than half of the initial capital for a longwall face. Therefore both from technical and economic points of view, the powered support is a very important piece of equipment in a long wall face. The application of modern powered supports can be traced back to early 1950’s. Since then, following its adoption in every part of the world, there have been countless models design and manufactured in various countries. But unfortunately, there still is no uniform system of classification. A simplified classification is used in this section. Since a powered support consists of four major components(i. e. , canopy, caving shield, hydraulic legs and props, and base plate), the ways by which they are interrelated are used for classification. In this respect, two factors are most important: (1) presence or absence of caving shield- if a caving shield is included, the support is a “shield” type, otherwise, a frame or a chock; (2) number and type of arranging the hydraulic legs- since support capacity is generally proportional to number of hydraulic legs, it is important to specify the number of hydraulic legs that a support has. Furthermore, the way the hydraulic legs are installed is important; for example, a vertical installation between the base and the canopy has the caving shield has the least efficiency in supporting the roof. Based on this concept, there are four types of powered support, that is, the frame, chock, shield and chock shield, in order of evolution of their development. However, it must be noted that the trend of development in each type is such that it becomes less distinguishable in terms of application. The four types of roof supports can be obtained for either longwall retreating or advancing systems, and they are available in standard, one-web-back, and immediate forward support (IFS) versions. With the standard system, the wining machine takes a cut or a slice, and the armored face conveyor is pushed over by the hydraulic rams that are fixed to the support units. The support units then are advanced sequentially to the conveyor. With the one-web-back system, a support is set back from the conveyor by a device that automatically keeps the leading edge of the support at a fix distance from the conveyor. This allows easy access though the face and employs the standard method of advancing; i. e. , pushing the conveyor first, and then advancing the support. With the IFS system, the support units is advanced to the conveyor immediately after the cutting machine has passed, and the forward canopy of the support units is long enough to the support both the recently and newly exposed roof sections. After the supports have been advanced, the conveyor is pushed over. FRAME The frame support is an extension of the single hydraulic props conventionally used underground. Thus it is the first type developed in modern self-advancing hydraulic powered supports. It involves setting up two hydraulic props or legs vertically in tandem that are connected at the top by a single or two segmented canopies. The two segmented canopies can be hinge-jointed at any point between the legs or in front of the front leg. The base of the two hydraulic legs may be a circular steel shoe welded at bottom of each leg or solid base connecting both legs. Generally, a frame support consists of two or three sets of hydraulic legs. The set moving first is the secondary set, the set moving later is the primary set. There is a double-acting ram installed between each set. The piston of the ram is connected to the secondary set and the cylinder to the primary set. During support advance, the primary set is set against the roof while the secondary set is lowered and pushed forward by the piston. Having reached the new position, the secondary set is against the roof while the primary set is lowered and pulled forward by the cylinder. The distance of each advance ranges from 20 to 36 in.(0.50 ~ 0.91m) The frame support is very simple, but more flexible or less stable structurally. There are considerable uncovered spaces between the two pieces of canopy which allows broken roof rock to fall through. Consequently, the frame support is not suitable for a weak roof. Frames have become seldom used because they are less stable and require frequent maintenance. CHOCK In a chock support, the canopy is a solid piece and the base may be either a solid or piece or two separate parts connected by steel bars at the rear and/or the front ends. In both cases a large open space is left at the center for locating the double-acting hydraulic ram which is used to push and pull the chain conveyor and the chock in a whole unit, respectively, a distinctive difference from the frame support. This setup is also used in the shields and chock shields. Again, all hydraulic legs are installed vertically between the base and the canopy. The number of legs ranges from three to six, but the four-leg chocks are by far the most popular ones. The six-leg chocks are designed for thin seams with two legs in the front and four legs in the rear, separated by a walkway. For the six-leg chocks, the canopy is generally hinge-jointed above the walkway. Most chock are also equipped with a gob window hanging at the rear end of the canopy. The gob window consists of several rectangular steel plates connected horizontally at both ends. In most chock supports, there are hinge joint connections between the legs and the canopy and between the legs and the base. But in order to increase the longitudinal stability, it is reinforced mostly with a box-shaped steel frame between the base and each leg. A leg restoring device is installed around each leg at the top of the box-shaped steel frame. The chocks are suitable for medium to hard roof. When the roof overhangs well into the gob and requires induced caving, the chocks can provide access to the gob. SHIELD Shields, a new entry in the early seventies, are characterized by the addition of a caving shield at the rear end between the base and the canopy. The caving shields, which in general are inclined, are hinge-jointed to the canopy and the base making the shield a kinematically stable support, a major advantage over the frames and the chocks. It also completely seals off the gob and prevents rock debris from getting into the face side of the support. Thus the shield-supported face is generally clean. The hydraulic legs in the shields are generally inclined to provide more open space for traffic. Because the canopy, caving shield, and base are interconnected, it can well resist the horizontal force without bending the legs. Thus, unlike the solid constraint in the frame/ chock supports, the pin connections between the legs and the canopy, and between the legs and the base in a shield support make it possible that the angle of inclination of the hydraulic legs varies with the mining heights. Since only the vertical component of hydraulic leg pressure is available for supporting the roof, the actual loading capacity of the shield also varies with the mining heights. There are many variations of the shield supports. In the following, six items are used to classify the shields, which enables a unified terminology to be developed for all kinds of shields. The types of motional traces of the canopy tip, leg positions and orientation, number of legs, canopy geometry, and other optional designs and devices can be clearly specified by the terminology . TYPES OF MOTIONAL TRACES FOR THE LEADING EDGE OF THE CANOPY. This is the most commonly recognized way of classifying the shield. Based on this criterion, there are three types, lemniscate, caliper , and ellipse. Lemniscate. This is the most popular type. The caving shield and the base are jointed by two lemniscate bars which have a total of four hinges. As the hydraulic legs are raised and lowered, the dimentions of the lemniscate bars are selected such that the leading edge of the canopy moves up and down nearly vertically , thus maintaining a nearly constant unsupported distance between the face-line and the leading edge of the canopy .This is a feature that is widely considered most desirable for good roof control . There are clear limits of mining height within which the leading edge of the canopy moves nearly vertically. These limits are strictly controlled by the dimentional and positional arrangements of the canopy, caving shield, lemniscate bars, and the base. Beyond these limits, the edges will move rapidly away from the face-line creating a large unsupported area. Caliper. In a caliper shield, the caving shield and the base are connected by a single hinge .When the hydraulic legs are raised, the leading edge of the canopy moves in an arc away from the face, thus increasing the unsupported area. This is considered by most users the least desirable feature of the caliper shield .But in practice if the seam thickness varies little, the dimentional and positional arrangement of canopy, caving shield, and the base can be so designed that the distance change of unsupported area will not be significant. On the other hand, when the legs are lowered, it reduces the unsupported area. Ellipse. In this type the caving shield and the base are so connected that when the hydraulic legs are moved up and down, the leading edge of the canopy follows an elliptical trace. This type is seldom used. CHOCK SHIELD The chock shield combines the features of the chocks and the shields. As such it possesses the advantages of both. If all of the four or six legs are installed between the canopy and the base, it is called a chock shield. There are regular four or six-leg chock shields in which all legs are vertical and parallel. Others form V or X shapes. Some canopies are a single piece and some are two pieces with a hydraulic ram at the hinge joint. The chock shield has the highest supporting efficiency. They are suitable for hard roof. 中文譯文 自移式液壓支架 現代長壁工作面采煤已經在開采區使用液壓支架。液壓支架不僅支撐頂板，推動刮板輸送機工作面和自移式支架本身，而且還為相關的采煤設備提供一個安全的工作環境。因此正確的選擇和應用液壓支架是長壁工作面采煤成功的先決條件。此外，由于對液壓支架需求數量很大，對液壓支架的投資經常要占到長壁采煤工作面初始投資的一半以上。因此，從技術和經濟兩方面的觀點看，液壓支架是長壁采煤工作面設備中十分重要的一部分。 現代液壓支架的應用可以追溯到上個世紀50年代早期。從那時開始，隨著液壓支架在全世界各個領域的使用，各個國家都設計和制造了無數的液壓支架。但是，到現在始終沒有一個統一的分類系統。 這里使用一個簡化的液壓支架的分類。由于液壓支架由四個主要部分組成(即頂梁，掩護梁，液壓支柱和底座)，因此根據這些結構的相互關系給液壓支架分類。在其中，有兩個因素是最重要的：(1) 是否使用掩護梁—如果使用了掩護梁，那么液壓支架屬于掩護式液壓支架，否則，支架就屬于節式支架或者垛式支架。（2）液壓支架所使用立柱的數量與類型—由于液壓支架的支護能力一般與液壓立柱的數目成正比，所以確定液壓支架立柱的數目是很重要的。另外，液壓支柱的安裝方式也很重要，例如，立柱垂直安裝在底座和有掩護梁的頂梁之間，此時對頂板具有最小的支護效率。 基于這個概念，按照液壓支架發展進化的順序，把液壓支架分為四類，即：節式支架，垛式支架，掩護式支架和支撐掩護式支架。然而，必須指出的是，每一種支架的發展趨勢在應用方面的區別在逐漸變小。 這四種類型的液壓支架不僅可以用于后退式長壁回采工作面和前進式開采工作面，還可以用于標準方式、滯后支護方式和即時支護方式。 對于標準支護方式，采煤機作切割或分段運動，工作面輸送機由裝在液壓支架上的推移千斤頂推動前進。液壓支架比輸送機先移動。對于滯后式支護方式，支架不可能靠近輸送機，因為有一個裝置自動的使支架前端與輸送機保持一定的距離。這就要求要有貫穿工作面的緩溝，并且采用前進式標準支護，比如：先推動刮板輸送機，然后再讓液壓支架前進。 對于即時支護方式，液壓支架在截煤機過去之后立即跟隨刮板輸送機前進，液壓支架前面的頂板有足夠的長度來支護采過和將要采的頂板部分。在液壓支架前進以后，刮板輸送機也被推移前進。 節式支架 節式液壓支架是一種擴展單體液壓支柱的常規使用的支架。它是現代自推進式液壓支架發展的第一個類型。它包括一前一后垂直安裝的支柱，支柱連接在單一或分割的頂梁的頂端。兩塊分割的頂梁可以鉸接在兩立柱之間或在前立柱之前的任意點。兩根液壓支柱的底部是焊接在每個支柱末端的一只金屬環形底靴或者固體底座連接兩根支柱。 一般來說，節式液壓支架由兩套或三套液壓立柱組成。先移動的是次要裝置，后移動的是主要裝置。每根支柱之間有雙作用液壓缸。液壓缸的活塞連接到次要之柱上，缸底連接到主要支柱上。支架前進過程中，當次要支柱降低并通過活塞推動向前移動時，主要支柱使頂梁平衡。當?shù)竭_新位置以后，次要支柱支撐頂板，主要支柱降低并且由缸筒拉動前進。每次移動的前進距離為20到30英尺。（即0.5到0.91米）。 節式液壓支架結構很簡單，但是在結構上柔韌性過強而缺少穩定性。兩塊頂板下有相當大的未覆蓋區域，這段區域允許碎石落入。因此，節式液壓支架不適合較弱頂板。由于缺少穩定性和需要頻繁維護，節式液壓支架現在已經很少使用。 垛式液壓支架 在垛式液壓支架中，頂梁是一個堅固的整體結構，而底座則可能是堅固的整體結構或者兩個獨立的部分，它們用金屬桿在其前端或尾部連接起來。在這兩種情況下，兩垛式支架之間將有一個很大的空間，并在其中部安裝雙作用立柱，這種立柱將把刮板輸送機和垛式液壓支架作為一個整體進行推移，這就是垛式液壓支架與節式液壓支架的不同。這種方式同樣應用于掩護式液壓支架和支撐掩護式液壓支架當中。 和節式液壓支架一樣，所有的液壓立柱垂直安裝在底座和頂板之間。立柱的數目在3到6之間，但4柱支架目前應用最多。六柱式垛式支架是為薄煤層設計的，兩個支柱在前，四個在后，中間是人行走的通道。對于六柱式支架，頂梁在通道的上方鉸接。大多數垛式支架在其頂梁末端都裝有擋矸簾。擋矸簾由一些矩形的金屬片組成，這些金屬片的兩端水平連接。 在大多數垛式支架中，液壓支柱與頂梁和液壓支柱與底座之間都采用鉸接式連接。但是為了增加支架的縱向穩定性，通常在底座與各支柱之間安裝箱形金屬框用來加強穩定性。在金屬框上方的立柱周圍安裝復位裝置。 垛式液壓支架適用于各種堅硬頂板。當部分頂板已經完全懸掛在采空區時，需要引導其塌落，這時垛式液壓支架就可以提供一條通向采空區的通道。 掩護式液壓支架 掩護式液壓支架是在七十年代新出現的一種液壓支架，它的特點是在底座和頂梁尾端增加了掩護梁。掩護梁一般是傾斜的，鉸接在頂梁和底座之間，從運動學上說，它是穩定的，這也是掩護式支架優于節式支架和多式支架的一個主要方面。掩護式支架可以完全封鎖采空區，防止巖石碎片落入支架的工作面。因此，掩護式液壓支架的工作面一般都比較清潔。 掩護式液壓支架的立柱一般都是傾斜的，這樣可以為運輸提供更多的空間。由于頂板、掩護梁和底座是相互連接的，所以掩護式液壓支架可以更好的抵抗橫向力，而不需要使立柱彎曲。這樣，與節式支架和垛式支架固定約束不同，掩護式液壓支架中支柱與頂梁和支柱與底座之間是通過銷軸連接的，使液壓支柱的傾斜角度隨著采煤高度的不同而變化成為可能。由于只有液壓立柱的垂直分量起支護頂板的作用，掩護式液壓支架的承載能力隨著采煤高度的變化而變化。 掩護是液壓支架有很多種類。在下面的介紹中，有六項可以用來給掩護是液壓支架分類，這六項可實現所有類型掩護式液壓支架統一術語的發展。頂梁端部的運動軌跡，液壓立柱的定位于定向，液壓立柱的數目，頂梁的幾何形狀，以及其他的可以任意選擇的設計方法和理念都可以用專業術語詳細的說明。 頂梁端部的運動軌跡的形式 這是公認的最普遍的對掩護是液壓支架的分類方法。基于這種標準，掩護是液壓支架可以分為三種類型：雙紐線形，圓弧形和橢圓形。 雙紐線形：這是最常用的一種類型。掩護梁和底座通過含有四個鉸鏈的雙紐線形運動的連桿連接起來。隨著掩護式液壓支架立柱的升起和下降，選擇好雙紐線桿的尺寸，就可以使頂梁前端近乎垂直的作上升和下降運動，這樣就可以保持頂梁前端與煤壁之間未支撐的距離為一常量，這種特性對很好控制頂板來說是廣泛考慮的最合乎要求的。當采煤高度有明顯限制時，頂梁前端垂直運動。頂梁、掩護梁、雙扭線桿和底座的尺寸及位置的布置都嚴格約束了這種限制。如超出這個限制，頂梁前端將會迅速的遠離采煤線，從而產生一個很大的未支護面積。 圓弧形：在圓弧形掩護式液壓支架中，掩護梁和底座之間通過單一的鉸接連接。當液壓支架立柱升起時，頂梁的前端將按圓弧型軌跡遠離煤壁，這樣使未支護面積增大。這就是大多數用戶所考慮的，圓弧型式掩護式液壓支架最不合適的地方。但在實際應用中，如果煤層厚度變化幅度較小，則頂梁、掩護梁和底座的尺寸及位置可以按這種形式設計，未支護面積處的縱向距離變得不重要。另外，當降低液壓支柱時，未支護面積將會減少。 橢圓形：在橢圓形掩護式液壓支架中，掩護梁和底座采用這種方式連接，當液壓支架的立柱作上升和下降運動時，支架頂板的前端沿橢圓形軌跡運動。這種形式的液壓支架現在已經很少應用了。 支撐掩護式液壓支架 支撐掩護式液壓支架結合了垛式液壓支架和掩護式液壓支架的特點。所以，支撐掩護式液壓支架具有以上兩者所具有的優點。 如果所有的四根或六根液壓立柱都安裝在頂梁和底座之間，則稱這種支架為支撐掩護式液壓支架。常規的四柱或六柱支撐掩護式液壓支架所有的立柱都是垂直安裝、互相平行的。另外還有V型和X型的安裝形式。有些頂梁是一個整體，而有些頂梁則是由通過鉸接并在鉸接處安裝一液壓千斤頂?shù)膬刹糠纸M成的。支撐掩護式液壓支架具有最高的支護效率，因此適用于堅硬頂板。