齒輥破碎機的設計【新型的輥顎破碎機】,新型的輥顎破碎機,齒輥破碎機的設計【新型的輥顎破碎機】,破碎,設計,新型 畢業設計（論文）任務書 I、畢業設計(論文)題目： 齒輥破碎機 II、畢 業設計(論文)使用的原始資料(數據)及設計技術要求： 1、齒輥破碎機的結構分析與設計結構合理 2、齒輥破碎機齒輥工作面有一定耐磨性及其整體強度要求 3、要保證被破碎的物料粒度均勻及過粉率低 III、畢 業設計(論文)工作內容及完成時間： 1、通過圖書館、上網查找大量書籍及相關資料 2周 2、齒輥破碎機的電機選擇及傳動機構設計 3周 3、帶傳動、齒輪傳動的計算 3周 4、齒輥參數計算 3周 5、鍵的選擇及其校核 2周 6、畢業論文整理及答辯準備 2周 Ⅳ 、主 要參考資料： 1 .陳灝. 機械設計手冊，第2版.機械工業出版社，2000 2 .唐大放，馮曉寧，楊現卿.機械設計工程學.徐州：中國礦業大學出版社,2001 3 .胡宗武，徐履冰，石來德.非標準機械設備設計手冊，2002 4 .甘永立.幾何量公差與檢測.上海：上?？茖W(xué)技術出版社，2001 5. 單輝祖.材料力學.北京：高等教育出版社，1999 航空工程 系 機械設計制造及自動化 專業類 0881054 班 學生（簽名）： 填寫日期： 2012 年 2 月 20 日 指導教師（簽名）： 助理指導教師(并指出所負責的部分)： 系主任（簽名）： 附注:任務書應該附在已完成的畢業設計說明書首頁。 學士學位論文原創性聲明 本人聲明，所呈交的論文是本人在導師的指導下獨立完成的研究成果。除了文中特別加以標注引用的內容外，本論文不包含法律意義上已屬于他人的任何形式的研究成果,也不包含本人已用于其他學位申請的論文或成果。對本文的研究作出重要貢獻的個人和集體，均已在文中以明確方式表明。本人完全意識到本聲明的法律后果由本人承擔。 作者簽名： 日期： 學位論文版權使用授權書 本學位論文作者完全了解學校有關保留、使用學位論文的規定，同意學校保留并向國家有關部門或機構送交論文的復印件和電子版，允許論文被查閱和借閱。本人授權南昌航空大學科技學院可以將本論文的全部或部分內容編入有關數據庫進行檢索，可以采用影印、縮印或掃描等復制手段保存和匯編本學位論文。 作者簽名： 日期： 導師簽名： 日期： 畢業設計（論文） 題目： 齒輥破碎機 系 別 航空與機械工程系 專業名稱 機械設計制造及其自動化 班級學號 088105439 學生姓名 朱芊全 指導教師 封立耀 二OO 年 月 畢業設計（論文）開題報告 題目 齒輥破碎機 專 業 名 稱 機械設計制造及自動化 班 級 學 號 088105439 學 生 姓 名 朱芊全 指 導 教 師 封立耀 填 表 日 期 年 月 日 一、選題的依據及意義： 隨著國家經濟建設的快速發展,將對礦藏資源需求量更高、更好，國家有限的資源量將無法滿足更多的需求，雙齒輥式破碎機不僅要具有高效性、環保性，更要具有復合性。通常使用的破碎機在工作時只能粗略的對礦石進行破碎，很多還需要二次破碎，仍無法滿足生產生活需要，為此就不得不改變物料的破碎方式，物料的破碎效率，物料破碎的安全性環保性等多方面問題，為解決此問題在老師的指導下我設計這臺雙齒輥式破碎機，它可以有效的解決上述問題。我相信這臺破碎機能有效的節省和利用資源，對于提高生產、率環境保護和降低成本將會起到?jīng)Q定性作用，它一定會有很廣闊的市場前景! 二、國內外研究概況及發展趨勢（含文獻綜述）： 輥式破碎機出現于1806年，它是一種較為古老的破碎設備。但是，由于它的結構簡單、緊湊輕便、易于制造、工作可靠，特別是它的產品過粉碎少，因此，至今仍在選煤、冶金燒結、水泥、玻璃、陶瓷等工業部門，以及小型選礦廠中使用，而且有新的改進與發展。輥式破碎機被廣泛用于破碎軟質和中等硬度的物料，對破碎濕料和黏性物料和堅硬物料，使用范圍受到了限制。 近年來，國外輥式破碎機發展的得很快，種類也很齊全。按輥子的數目，輥式破碎幾可以分為單輥、雙輥、三輥、和四輥四種；按輥面形狀，可以分為光輥、齒輥、槽輥破碎機，輥式破碎機等等 就其結構而言，大多采用自動移動輥機結構，液壓調整，油—液控制系統等新技術、新結構。但各制造廠所采用的結構形式和控制系統各有不同，獨具特色。如美國Pettibone公司生產的雙輥破碎機，應用橡膠輪胎傳動，液壓調整機構，采用自動定位滾子軸承，運轉平穩，使用壽命較長。還有美國Portec公司生產的三輥破碎機，由一個固定輥和兩個移動輥組成。移動輥由彈簧保持壓力及固定工作位置。固定輥由齒輪驅動，移動輥由橡膠輪胎傳動，可進行單向給料破碎和雙向給料破碎。三輥破碎機由單輥破碎機和雙輥破碎機組合而成。而四輥破碎機由兩個雙輥破碎機組合而成，這種破碎機能完成粗碎和終碎兩道工序，破碎效率很高。輥式破碎機的規格用輥子直徑D和長度L表示，例如輥子直徑為1200mm，輥子長度為為1000mm的輥式破碎機表示為：Φ1200mm×1000mm輥式破碎機。 3、 研究內容及實驗方案： 設計目標： 提高雙輥齒破碎機齒輥耐磨性和整體強度，使得齒輥在整個破碎工作過程中，不會因雙齒輥破碎機輥齒的長時間工作和物料粒度過大而發生變形，降低事故率，提高破碎效率，保證生產的正常進行，提高勞動生產率。 研究內容： （1）結構分析設計； （2）分析雙齒輥破碎機齒輥工作面耐磨性及其整體強度； （3）整體結構優化。 四、目標、主要特色及工作進度 1、通過圖書館、上網查找大量書籍及相關資料 2周 2、齒輥破碎機的電機選擇及傳動機構設計 3周 3、帶傳動、齒輪傳動的計算 3周 4、齒輥參數計算 3周 5、鍵的選擇及其校核 2周 6、畢業論文整理及答辯準備 2周 5、 參考文獻 1 .陳灝. 機械設計手冊，第2版.機械工業出版社，2000 2 .唐大放，馮曉寧，楊現卿.機械設計工程學.徐州：中國礦業大學出版社,2001 3 .胡宗武，徐履冰，石來德.非標準機械設備設計手冊，2002 4 .甘永立.幾何量公差與檢測.上海：上?？茖W(xué)技術出版社，2001 5. 單輝祖.材料力學.北京：高等教育出版社，1999 6 .付峻青等.MMD625分級破碎機的應用研究.煤炭科學技術，2001 8 .煤科院唐山分院.齒形結構及齒的布置形式研究報告，1998 9 .錢振倫.移動式和半移動式破碎機的發展方向.礦山機械，1993 10.許居午等.新型輥式破碎機軸承座的有限元計算.礦山機械，1993 11.周杰等.新型強力分級破碎機的設計研究.煤炭加工與綜合利用，1999 12.梁金剛.煤用齒輥式破碎機的現狀及新發展.選煤技術，2001 13.方昆凡.公差與配合技術手冊.北京：北京出版社，1998 齒輥破碎機 學生姓名：朱芊全 班級：088105439 指導老師：封立耀 摘要：新型雙齒輥破碎機由于結構緊湊，破碎物料機理合理，適應性強等突出的優點，在露天礦物料粗碎應用中很有發展前途，是較為理想的露天礦巖石破碎機。 本設計所涉及的新型的輥顎破碎機結合了顎式破碎機和齒輥破碎機的優點，使生產能力得到了很大的提高，出料粒度的均一性得到了很好的保證，使物料得到了有效的破碎，這是有生產的實踐為證的。本文首先對新型雙齒輥破碎機進行了電機的選擇、傳動機構的設計;然后對齒輥的參數進行計算，包括：輸入軸、偏心軸、小齒輥軸的結構設計及校核等；最后進行鍵的選擇及校核，包括：電機軸上、輸入軸上、偏心軸上、小齒輥軸上的鍵。 關鍵詞：新型雙齒輥破碎機 顎式破碎機 結構設計 指導老師簽名： Teeth roll crusher Student name： Zhu Qianquan Class: 088105439 Supervisior: Feng Liyao Abstract: Mineral sizer because the structure is compact, broken material mechanism is reasonable, strong adaptability of such prominent advantages, the original material crushing application promising, is the ideal open-pit mine rock crusher. The design of the new type of roller involved jaw crusher combines jaw crusher and the advantages of the teeth roll crusher, make the production capacity were greatly increased, the grain-size homogeneity of got a very good guarantee, make the material effectively of broken, it is the practice of production for the card. This paper first to mineral sizer the choice of the motor, a transmission mechanism design; And then the teeth roll the parameters of the computation, including: input shaft, eccentric shaft, small teeth of the roller structure design and check; The last key selection and checking, including: motor shaft, input shaft, eccentric shaft on small teeth, the key on the roller. keywords: mineral sizer jaw crusher structure design Signature of Supervisior: 外文資料翻譯 題目： 齒輥破碎機 系 別 航空與機械工程系 專業名稱 機械設計制造及自動化 班級學號 088105439 學生姓名 朱芊全 指導教師 封立耀 二O一二 年 三 月 第 18 頁 翻譯 英文原文 COMMINUTION IN A NON-CYLINDRICAL ROLL CRUSHER* P. VELLETRI ~ and D.M. WEEDON ~ ~[ Dept. of Mechanical & Materials Engineering, University of Western Australia, 35 Stirling Hwv, Crawley 6009, Australia. E-mail piero@mech.uwa.edu.au § Faculty of Engineering and Physical Systems, Central Queensland University, PO Box 1!:;19, Gladstone, Qld. 4680, Australia (Received 3 May 2001; accepted 4 September 2001) ABSTRACT Low reduction ratios and high wear rates are the two characteristics ntost commonh" associated with conventional roll crushers. Because of this, roll crushers are not often considered Jor use in mineral processing circuits, attd many of their advantages are being largely overlooked. This paper describes a novel roll crusher that has been developed ipt order to address these issues.Relbrred to as the NCRC (Non-Cylindrical Roll Crusher), the new crusher incorporates two rolls comprised qf an alternating arrangement of platte attd convex or concave su@wes. These unique roll prqfiles improve the angle qf nip, enabling the NCRC to achieve higher reduction ratios than conventional roll crushers. Tests with a model prototype have indicated thar evell fi)r very hard ores, reduction ratios exceeding lO:l can be attained. In addition, since the comminution process in the NCRC combines the actions of roll arM jaw crushers there is a possibili O' that the new profiles may lead to reduced roll wear rates. ? 2001 Elsevier Science Ltd. All rights reserved. Keywords: Comminution; crushing INTRODUCTION Conventional roll crushers suffer from several disadvantages that have lcd to their lack of popularity in mineral processing applications. In particular, their low reduction ratios (typically limited to about 3:1) and high wear rates make them unattractive when compared to other types of comminution equipment, such as cone crushers. There are, however, some characteristics of roll crushers that are very desirable from a mineral processing point of view. The relatively constant operating gap in a roll crusher gives good control over product size. The use of spring-loaded rolls make these machines tolerant to uncrushable material (such as tramp metal). In addition, roll crushers work by drawing material into the compression region between the rolls and do not rely on gravitational feeci ~like cone and jaw crushers. This generates a continuous crushing cycle, which yields high throughput rates and also makes the crusher capable of processing wet and sticky ore. The NCRC is a novel roll crusher that has been dcveloped at the University of Western Australia in ordcr to address some of the problems associated with conventional roll crushers. The new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaccs. Thcse unique roll profiles improve the angle of nip, enabling the NCRC to achieve higher reduction ratios than conventional roll crushers. Preliminary tests with a model prototype have indicated that, even for very hard oics, reduction ratios exceeding 10:I can be attained (Vellelri and Weedon, 2000). These initial findings were obtained for single particle feed. where there is no significant interaction between particles during comminution. The current work extends the existing results bv examining inulti-particle comminution inthe NCRC. It also looks at various othcr factors that influencc the perli~rmance of the NCRC and explores the effectiveness of using the NCRC for the processing of mill scats. PRINCIPLE OF OPERATION The angle of nip is one of the main lectors effccting the performance of a roll crusher. Smaller nip angles are beneficial since they increase tl~e likelihood of parlictes bcing grabbed and crushed by lhe rolls. For a given feed size and roll gap, the nip angle in a conventional rtHl crusher is limited by the size of thc rolls. The NCRC attempts to overcome this limitation through the use of profiled rolls, which improve the angle of nip at various points during one cycle (or revolution) of the rolls. In addition to the nip angle, a number of other factors including variation m roll gap and mode of commmution were considered when selecting Ille roll profiles. The final shapes of the NCRC rolls are shown in Figure I. One of the rolls consists {sI an alternating arrangement of plane and convex surfaces, while the other is formed from an alternating arrangement of phme and concave surlaccs. The shape of the rolls on the NCRC result in several unique characteristics. Tile most important is that, lk)r a given particle size and roll gap, the nip angle generated m the NCRC will not remain constant as the rolls rotate. There will be times when the nip angle is much lower than it would be for the same sized cylindrical rolls and times when it will be much highcr. The actual variation in nip angle over a 60 degree roll rotation is illustrated in Figure 2, which also shows the nip angle generated under similar conditions m a cylindrical roll crusher of comparable size. These nip angles were calculated for a 25ram diameter circular particle between roll of approximately 200ram diameter set at a I mm minimum gap. This example can be used to illustrate the potential advantage of using non-cylindrical rolls. In order for a particle to be gripped, thc angle of nip should normally not exceed 25 ° . Thus, the cylindrical roll crusher would never nip this particle, since the actual nip angle remains constant at approximately 52 °. The nip angle generated by the NCRC, however, tidls below 25 ° once as the rolls rotate by (~0 degrees. This means that the non-cylindrical rolls have a possibility of nipping the particlc 6 times during one roll rewHution. EXPERIMENTAL PROCEDURE The laboratory scale prototype of the NCRC (Figure 3) consists of two roll units, each comprising a motor, gearbox and profiled roll. Both units are mounted on linear bearings, which effectively support any vertical componcnt of force while enabling horizontal motion. One roll unit is horizontally fixed while the other is restrained via a compression spring, which allows it to resist a varying degree of horizontal load. The pre-load on the movable roll can be adjusted up to a maximum of 20kN. The two motors that drive the rolls are electronically synchronised through a variable speed controller, enabling the roll speed to be continuously varied up to 14 rpm (approximately 0.14 m/s surface speed). The rolls have a centre-to-centre distance ~,at zero gap setting) of I88mm and a width of 100mm. Both drive shafts are instrumented with strain gauges to enable the roll torque to be measured. Additional sensors are provided to measure the horizontal force on the stationary roll and the gap between the rolls. Clear glass is fitted to the sides of the NCRC to facilitate viewing of the crushing zonc during operation and also allows the crushing sequence to bc recorded using a high-speed digital camera. Tests were performed on several types of rocks including granite, diorite, mineral ore, mill scats and concrete. The granite and diorite were obtained from separate commercial quarries; the former had been pre-crushed and sized, while the latter was as-blasted rock. The first of the ore samples was SAG mill feed obtained from Normandy Mining's Golden Grove operations, while the mill scats were obtained from Aurora Gold's Mt Muro mine site in central Kalimantan. The mill scats included metal particles of up to 18ram diameter from worn and broken grinding media. The concrete consisted of cylindrical samples (25mm diameter by 25ram high) that were prepared in the laboratory in accordance with the relevant Australian Standards. Unconfined uniaxial compression tests were performed on core samples (25mm diameter by 25mm high) taken from a number of the ores. The results indicated strength ranging from 60 MPa for the prepared concrete up to 260 MPa for the Golden Grove ore samples. All of the samples were initially passed through a 37.5mm sieve to remove any oversized particles. The undersized ore was then sampled and sieved to determine the feed size distribution. For each trial approximately 2500g of sample was crushed in the NCRC. This sample size was chosen on the basis of statistical tests, which indicated that at least 2000g of sample needed to be crushed in order to estimate the product P80 to within +0.1ram with 95% confidence. The product was collected and riffled into ten subsamples, and a standard wet/dry sieving method was then used to determine the product size distribution. For each trial, two of the sub-samples were initially sieved. Additional sub-samples were sieved if there were any significant differences in the resulting product size distributions. A number of comminution tests were conducted using the NCRC to determine the effects of various parameters including roll gap, roll force, feed size, and the effect of single and multi-particle feed. The roll speed was set at maximum and was not varied between trials as previous experiments had concluded that there was little effect of roll speed on product size distribution. It should be noted that the roll gap settings quoted refer to the minimum roll gap. Due to the non-cylindrical shape of the rolls, the actual roll gap will vary up to 1.7 mm above the minimum setting (ie: a roll gap selling of l mm actually means 1-2.7mm roll gap). RESULTS Feed material The performance of all comminution equipment is dependent on the type of material being crushed. In this respect, the NCRC is no different. Softer materials crushed in the NCRC yield a lower P80 than harder materials. Figure 4 shows the product size distribution obtained when several different materials were crushed under similar conditions in the NCRC. It is interesting to note that apart from the prepared concrete samples, the P80 values obtained from the various materials were fairly consistent. These results reflect the degree of control over product size distribution that can be obtained with the NCRC. Multiple feed particles Previous trials with the NCRC were conducted using only single feed particles where there was little or no interaction between particles. Although very effective, the low throughput rates associated with this mode of comminution makes it unsuitable for practical applications. Therefore it was necessary to determine the effect that a continuous feed would have to the resulting product size distribution. In these tests, the NCRC was continuously supplied with feed to maintain a bed of material level with the top of the rolls. Figure 5 shows the effect that continuous feed to the NCRC had on the product size distribution for the Normandy Ore. These results seem to show a slight increase in P80 with continuous (multi-particle) feed, however the shift is so small as to make it statistically insignificant. Similarly, the product size distributions would seem to indicate a larger proportion of fines for the continuously fed trial, but the actual difference is negligible. Similar trials were also conducted with the granite samples using two different roll gaps, as shown in Figure 6. Once again there was little variation between the single and multi-particle tests. Not surprisingly, the difference was even less significant at the larger roll gap, where the degree of comminution (and hence interaction between particles) is smaller. All of these tests would seem to indicate that continuous feeding has minimal effect on the performance of the NCRC. However, it is important to realise that the feed particles used in these trials were spread over a very small size range, as evident by the feed size distribution shown in Figure 6 (the feed particles in the Normandy trials were even more uniform). The unilormity in feed particle size results in a large amount of free space, which allow:s for swelling of the broken ore in the crushing chamber, thereby limiting the amount of interaction between particles. True "choke" feeding of the NCRC with ore having a wide distribution of particle sizes (especially in the smaller size range) is likely to generate much larger pressures in the crushing zone. Since the NCRC is not designed to act as a "'high pressure grinding roll" a larger number of oversize particles would pass between the rolls under these circumstances. Roll gap As with a traditional roll crusher, the roll gap setting on the NCRC has a direct influence on the product size distribution and throughput of the crusher. Figure 7 shows the resulting product size distribution obtained when the Aurora Gold ore (mill scats) was crushed at three different roll gaps. Plotting the PSO values taken from this graph against the roll gap yields the linear relationship shown in Figure 8. As explained previously, the actual roll gap on the NCRC will vary over one revolution. This variation accounts for the difference between the specified gap setting and product Ps0 obtained from the crushing trials. Figure 8 also shows the effect of roll gap on throughput of the crusher and gives an indication of the crushing rates that can be obtained with the laboratory scale model NCRC. Roll force The NCRC is designed to operate with minimal interaction between particles, such that comminution is primarily achieved by fracture of particles directly between the rolls. As a consequence, the roll force only needs to bc large enough to overcome the combined compressive strengths of the particles between the roll surlaces. If the roll force is not large enough then the ore particles will separate the rolls allowing oversized particles to lall through. Increasing the roll force reduces the tendency of the rolls to separate and therefore provides better control over product size. However, once a limiting roll force has been reached (which is dependent on the size and type of material being crushed) any further increase in roll force adds nothing to the performance of the roll crusher. This is demonstrated in Figure 9, which shows that for granite feed of 25-3 Imm size, a roll force of approximately 16 to 18 kN is required to control the product size. Using a larger roll force has little effect on the product size, although there is a rapid increase in product P80 if the roll force is reduced bek>w this level. As mentioned previously, the feed size distribution has a significant effect on the pressure generated in the crushing chamber. Ore that has a finer feed size distribution tends to "choke" the NCRC more, reducing the effectiveness of the crusher. However, as long as the pressure generated in not excessive the NCRC maintains a relatively constant operating gap irrespective of the feed size. The product size distribution will, therefore, also bc independent of the feed size distribution. This is illustrated in Figure 10, which shows the results of two crushing trials using identical equipment settings but with feed ore having different size distributions. In this example, the NCRC reduced the courser ore from an Fs0 of 34mm to a Ps0 of 3.0mm (reduction ratio of 11:1), while the finer ore was reduced from an Fs0 of 18mm to a Pso of 3.4mm (reduction ratio of 5:1). These results suggest that the advantages of using profiled rolls diminish as the ratio of the feed size to roll size is reduced. In other words, to achieve higher reduction ratios the feed particles must be large enough to take advantage of the improved nip angles generated in the NCRC. Mill scats Some grinding circuits employ a recycle or pebble crusher (such as a cone crusher) to process material which builds up in a mill and which the mill finds hard to break (mill scats). The mill scats often contain worn or broken grinding media, which can find its way into the recycle crusher. A tolerance to uncrushable material is therefore a desirable characteristic for a pebble crusher to have. The NCRC seems ideally suited to such an application, since one of the rolls has the ability to yield allowing the uncrushable material to pass through. The product size distributions shown in Figure 1 1 were obtained from the processing of mill scats in the NCRC. Identical equipment settings and feed size distributions were used for both results, however one of the trials was conducted using feed ore in which the grinding media had been removed. As expected, the NCRC was able to process the feed ore containing grinding media without incident. However, since one roll was often moving in order to allow the grinding media to pass, a number of oversized particles were able to fall through the gap without being broken. Consequently, the product size distribution for this feed ore shows a shift towards the larger particle sizes, and the Ps0 value increases from 4ram to 4.7mm. In spite of this, the NCRC was still able to achieve a reduction ratio of almost 4:1. Wear Although no specific tesls were conducted to determine the wear rates on the rolls of the NCRC, a number of the crushing trials were recorded using a high-speed video camera in order to try and understand the comminution mechanism. By observing particles being broken between the rolls it is possible to identify portions of the rolls which are likely to suffer from high wear and to make some subjective conclusions as to the effect that this wear will have on the perlbrmance of the NCRC. Not surprisingly, the region that shows up as being the prime candidate for high wcar is the transition between the flat and concave surfaces. What is surprising is that this edge does not play a significant role in generating the improved nip angles. The performance of the NCRC should not be adversely effccted by wear to this edge because it is actually the transition between the fiat and convex surfaces (on the opposing roll) that results in the reduced nip angles. The vide() also shows that tor part of each cycle particles are comminuted between the flat surfaces of the rolls, in much the same way as they would be in a jaw crusher. This can be clearly seen on the sequence of images in Figure 12. The wear on the rolls during this part of the cycle is likely' to be minimal since there is little or no relative motion between the particles and the surface of the rolls. CONCLUSIONS The results presented have demonstrated some of the factors effecting the comminution of particles in a non-cylindrical roll crusher. The high reduction ratios obtained from early single particle tests can still be achieved with continuous multi-particle feed. However, as with a traditional roll crusher, the NCRC is susceptible to choke feeding and must be starvation fed in order to operate effectively. The type of feed material has little effect on the performance of the NCRC and, although not tested, it is anticipated that the moisture content of the feed ore will also not adversely affect the crusher's per[Brmance. Results from the mill scat trials are particularly promising because they demonstrate that the NCRC is able to process ore containing metal from worn grinding media. The above factors, in combination with the flaky nature of the product generated, indicate that the NCRC would make an excellent recycle or pebble crusher. It would also be interesting to determine whether there is any difference in the ball mill energy required to grind product obtained from the NCRC compared that obtained from a cone crusher. 中文譯文 摘要 低的破碎比和高的磨損率是與傳統的破碎機相聯系的很常見的兩個特性。因為這點，在礦石處理流程的應用中，很少考慮到它們，并且忽略了很多它們的優點。本文描述了一個已被發展起來的新穎的對輥破碎機，旨在提出這些論點。作為NCRC,這種新式破碎機結合了兩個輥筒，它們由一個交替布置的平面和一個凸的或者凹的表面組成。這種獨特的輥筒外形提高了嚙合角，使NCRC可以達到比傳統輥式破碎機更高的破碎比。用一個模型樣機做的試驗表明：即使對于非常硬的礦石，破碎比任可以超過10。另外，既然在NCRC的破碎處理中結合了輥式和顎式破碎機的作用，那就有一種可能：那種新的輪廓會帶來輥子磨損率的降低。 關鍵字： 介紹 傳統的輥筒破碎機因為具有幾個缺陷而導致了其在礦石處理應用中的不受歡迎。尤其是當與其它的一些破碎機比起來，諸如圓錐破碎機等，它們的低破碎比（一般局限在3以內）和高的磨損率使它們沒