高樓清洗機機電系統設計,高樓清洗機機電系統設計,高樓,清洗,機電,電機,系統,設計 附 錄 The new high pressure cleaning the car With the rapid development of industry, environment pollution is becoming more and more serious, the environmental protection question is already a global strategy. In order to adapt to the needs of the construction of urban environmental sanitation, clear in time the city, improve air quality, sanitation vehicles of development and development, has become an important topic of the set before us. The development of urbanization in our country, the increase of the road to the requirements of environmental protection and improve, which makes the sanitation car requirement increasingly, high pressure cleaning the car as a sanitation in vehicles, having to clean the road, guardrail and purify airy action, is one of the important urban environmental protection equipment. The current domestic production of high pressure cleaning car backward in technology, there are many problems; Foreign cleaning vehicle performance while is superior, but the price is expensive, need a lot of foreign exchange, it is not the solution to the problem. Therefore, the development of new high pressure cleaning cars has become China's urban environmental protection work important problem to be solved. It not only with independent intellectual property rights, and can improve the design level of our country special automobile, driving the sanitation vehicles in China to develop and manufacture independent design ability. 1 a general introduction High pressure cleaning cars mainly by the power system, water system and hydraulic system, electronic control and manipulate system components. Power system for cleaning the car to walk and water pumps provide motivation. Water system mainly by the high pressure pump, water tank, valve, nozzle and other components, water through the pump pressure can improve after to 8 MP, form high pressure jet spraying to road, effectively flush the sand dust. Hydraulic system mainly by the hydraulic pump and motor and and valve set and other components, control vehicle to walk and injection action. Electric control part by sensors, SCM and main display control panel etc. In this paper the development of high pressure cleaning car main technical parameters are as follows: The rating capacity; Engine output power 45 KW; The biggest water spray width is not less than 3 m; Spray work for vehicle speed 5 km/h; Spray water pressure is not less than 8 MP; Total number of nozzle 21; Water pump water largest amount 65 km/h. 2 power distribution and switching system 2.1 the basic principle of the power transmission and scheme selection High pressure cleaning car according to the function of the realization of the divided into two kinds of state: a normal work is driving condition, high pressure cleaning the car and general at the same car, realize the transfer function; vehicle 2 it is watering operations state, the state in the vehicle with very low, the speed of the high pressure water spray homework, cleaning the road. Due to the high pressure cleaning the car need driving and driven two aspects of the pump power, so the dynamic how to provide design is to consider when the primary issue. At home and abroad and usually use the power distribution solutions has two, one is to adopt double configuration of the engine power transmission system, is main engine vehicles not alter, transmission system will not do change, use a Taiwan independence in vehicles outside the system of power auxiliary engine drive hydraulic system for high pressure pump provide motivation. The advantages of this scheme is simple in structure, the price is low, the disadvantage is as the vehicle in the water spray work driving the speed, low speed less than 10 km/h, this time the main engine can't work in the best working point, that power allocation is not reasonable, can produce fuel and power waste, and occupy the space of vice engine body, less the water storage volume, vice vehicle engine installation added new vibration noise sources, the influence the stability of the vehicle. Another plan is to use the vehicle engine vehicle transmission system and hydraulic system provide the power, through the points with FenDongXiang action, in the transfer road, driven by the main engine FenDongXiang to driving axle differentials, high speed movement; vehicle In injection homework road, driven by the main engine FenDongXiang to hydraulic system, on the one hand, control operation speed, on the other hand, the drive pump water spray. The scheme with the foregoing scheme, its advantage is compared, giving full play to the engine power, make the vehicle in the water spray operations can still working at high speed rating of the work of the state, not only save one engine, reduce the fuel consumption, and engine exhaust emission index is more advantageous to achieve urban environmental protection requirement. The vehicle structure more reasonable, vehicle weight of low, water storage space increases. To sum up, single engine configuration is a more reasonable configuration, so this paper power in the new, high pressure cleaning vehicle design, using a single engine design scheme. 2.2 power distribution To ensure the high pressure pump provide of the injection pressure is constant, drive the hydraulic loop quantitative hydraulic pump must work in constant speed rating of the work of the state, water spray operations vehicle of the speed and the road of injection effect is also not to change about the amount of driving, so drive the variable pump will work in constant speed rating of the work of the state, the consumption of driving power also for setting value. Thus, when the engine power to homework for setting value. 2.3 new single axis FenDongXiang design FenDongXiang power distribution is the core of the system, the traditional thought of design FenDongXiang usually adopts two to three axis structure of power distribution. This paper introduces the design of new light high-pressure cleaning vehicle USES the chassis is isuzu NKR55LLA light chassis, with traditional structure of the FenDongXiang sizes too large, can't meet the size requirement. According to the characteristics of the power distribution system, independent design and development of the single shaft driving, the FenDongXiang greatly reduced the FenDongXiang size, make body structure more compact. 3 hydraulic system The hydraulic control system is watering operations every action when the key to meeting, and the main variable pump, the quantitative pump, the drive motors, hydraulic cylinder, cooler, integrated control valves piece, filter etc. From the function of the realization of the perspective, hydraulic system by hydraulic motor drive travel system and hydraulic pressure motor drive water spray system two sub-systems. 3.1 hydraulic motor drive driving system The variable pump, hydraulic motor and the corresponding hydraulic loop hydraulic subsystem, a walk for the system for oil pump, and quantitative pump coaxial connected. This system consists of integrated control valves to realize the control of hydraulic pump and hydraulic system. The variable pump and motor selection, according to the basic power to determine the value. 3.2 hydraulic motor drive water spray system Hydraulic motor drive water spray system by quantitative pump, quantitative hydraulic motor, water pump, relief valve, cooler, filter and hydraulic cylinder and stacked valves group etc. For the hydraulic cylinder and stacked valves group together, for the control of water spray frame lift, extendable such action. The hydraulic oil tank, passes through to return to cooler water. 4 water injection system The water system is high pressure cleaning the car mainly by the core part high pressure water pump, water spray nozzle, frame, the spray gun and valve etc. Water tank flow of water out of the pump will improve after water pressure to 8 MP, form high pressure jet spraying to the road. The high pressure pump rational selection of engine efficiency, the best utilization, best flush efficiency have important influence, need according to the design requirements and engine parameters, such as to determine the high-pressure pump power, speed and the parameters such as pump pressure at work. Water system design of the main problems including the following two aspects. 4.1 the telescopic multi-degree-of-freedom water spray frame Water spray frame is injection system of actuators, installed in high pressure cleaning car head, high pressure water spray nozzle in the frame. To increase the width of the jet wash, design the new hydraulic control expansion institutions. Work, install a nozzle two of the rear protruding from the front of the car, and the nozzle into a straight line, and the high pressure water jet to; After completion of work, back to the nozzle tube retract side. Water spray frame from ground level also controlled by hydraulic system, also designs of the mechanical structure, highly fine-tuning height adjustment to trace. 4.2 water spray system parameters optimization High pressure cleaning the car is the purpose of the quality of the road surface cleaning out clean, so, how to improve the cleaning effect, water conservation is design to consider when important question, also is the past studies the problem of no point to consider. The effect of road surface cleaning and many parameters. Including injection height, the shape of the nozzle, injection pressure, injection Angle, jet width, nozzle diffusion Angle, distance of the nozzle. Through a lot of the theoretical and experimental research, to determine the height of the injection pressure injection, jet Angle, the width of the jet, the nozzle of the diffusion Angle of pavement, wash the best results, the wash rate in above, clean unit area of the pavement, the consumption of water and energy, reached the best matching value. 5 electronic control and operation system design Electronic control system to realize the working state of the vehicle display, monitoring, alarm and control etc. Function. Mainly includes the instrument shows system, dashboard, the hydraulic oil drive speed dial, hydraulic oil temperature display, hydraulic display, water tank water of the display and alarm, PenShuiGuan working status display, hydraulic system running time records, and other functions, the whole system USES modular design, the control panel integrated in driving indoor proper place, facilitate the operator control operation. The water tank of the monitoring and forecast of electric control system is the important link, must be strictly controlled. Tank water after cooler for hydraulic oil after cooling to enter high pressure pump and so have a water tank must be reserved to the amount of water. In the the design of the magnetic levitation type level sensor, accurately measure the level of height. Control system mainly including operation box, the power switch handle, oil, left, pedal drove speed, PenShuiGuan right control handle, water spray handle adjustable control handle to and fro and speed of the pedals. The design of the control system, the arrangement of the operation box, structure, the handle position, fully considered the man-machine engineering requirements, easy to control. 6 general structure design On the structure, the vehicle including chassis (with cab), water tank, hydraulic oil tank, water pump, FenDongXiang, water spray rack large components. Water pump and hydraulic pressure tank parallel is decorated in the cabin and water tank, or so between both sides put hinged door outside using, open convenient, convenient in maintenance inspection. Water tank use stainless steel structure, outside the oval with decoration side wai and skirt edge. FenDongXiang arrangement in the chassis and the hydraulic oil tank in water pump, transmission and the second transmission shaft between. Vehicle used Unigraphics software for 3 d software entities, and USES the design of the vehicle assembly function of virtual assembly. 7 conclusion The development of new high pressure cleaning car, in order to improve the effect of washing and energy saving as the core, using a single engine the configuration of the power distribution way, give full play to the water spray operations of engine power, improving the pressure of spray water; And the pavement flush the influence on the effect of parameters are optimized. The power distribution system, hydraulic system, water system, electronic control and control system, overall structure are studied. In the bodywork, single axis FenDongXiang development and research aspects such as road flush effect for several patents. This paper developed new high pressure cleaning car, prototype test each index, through to reserve requirements. High pressure cleaning the development of the new car, for the country's high performance high-pressure cleaning the car independent development and played a good role. 新型高壓清洗車 隨著工業的迅猛發展，環境污染顯得越來越嚴重，環保問題已是一個全球的戰略問題。為適應城市環境衛生建設的需要，及時清理城市路面，改善空氣質量，環衛車輛的開發和發展，已成為擺在我們面前的重要課題。我國城市化的發展，道路的增加及對環保要求的提高，使得對環衛車的需求日益增加，高壓清洗車作為環衛車輛中的一種，具有清洗道路、護欄和凈化空氣的作用，是城市環保的一種重要設備 。目前國內生產的高壓清洗車技術落后，存在許多問題；國外的清洗車性能雖然優越，但價格昂貴，需要大量的外匯，終究不是解決問題的辦法。為此，開發新型的高壓清洗車已成為我國城市環保工作中需要解決的重要問題。它不但具有自主知識產權，而且可以提高我國專用車的設計水平，帶動我國環衛車輛的自主設計開發及制造能力。 1 總體介紹 高壓清洗車主要由動力系統、水系統、液壓系統、電控及操縱系統等部分組成。動力系統為清洗車的行走和水泵提供動力。水系統主要由高壓水泵、水箱、閥、噴嘴等組成，水流經水泵后壓力可以提高到8MP，形成高壓射流噴射到路面，有效地沖洗路面的灰塵砂粒。液壓系統主要由液壓泵、馬達和和閥組等組成，控制車輛的行走和噴射動作。電控部分主要由傳感器、單片機及顯示控制面板等組成 。本文開發的高壓清洗車主要技術參數如下： 額定容量 ；發動機輸出功率 45KW；最大噴水寬度不小于3m；噴射工作時車輛行駛速度為 5km/h；噴射水壓不小于8MP；噴嘴總數 21 個；水泵最大噴水量 65km/h。 2動力分配及切換系統 2.1動力傳動的基本原理及方案選擇 高壓清洗車根據其實現的功能分為兩種工作狀態：一是正常行駛狀態，此時高壓清洗車和一般的車一樣，實現車輛的轉移功能；二是噴水作業狀態，在此狀態下，車輛以很低的速度進行高壓噴水作業，清洗路面。由于高壓清洗車需要行駛和驅動水泵兩方面的動力，所以該動力如何提供是設計時需要考慮的首要問題。 目前國內外通常使用的動力分配方案有兩種，一是采用雙發動機配置的動力傳動系統，即車輛主發動機不作改動，傳動系統也不作改動，使用一臺獨立于車輛動力系統之外的輔助發動機驅動液壓系統為高壓水泵提供動力。 該方案的優點是結構簡單，價格較低，缺點是由于車輛在噴水工作時低速行駛，其速度小于10km/h，此時主發動機不能工作在最佳工作點，使功率分配不合理，會產生燃料和功率的浪費，同時副發動機占據車身的空間，相對減少了車輛的蓄水體積，副發動機的安裝增加了新的振動噪聲源，影響整車的穩定性。 另外一種方案是采用車用主發動機為車輛傳動系統和液壓系統提供動力，通過分動箱的分動作用，在轉移行駛時，動力由主發動機經分動箱到后橋差速器，車輛高速運動；在噴射作業行駛時，動力由主發動機經分動箱傳到液壓系統，一方面控制作業行駛速度，另一方面驅動水泵噴水。 該方案與前述方案相比較，其優點在于，充分發揮了發動機的功率，使車輛在噴水作業時仍可以工作在高轉速的額定工作狀態，不但節省了一臺發動機，降低了燃油消耗，同時發動機尾氣排放指標更有利于達到城市環保要求。整車的結構更加合理，車輛的自重較低，蓄水空間相應增加。綜上所述，單發動機配置是一種更為合理的動力配置方案，所以本文在新型高壓清洗車的設計中，采用了單發動機的設計方案。 2.2功率的合理分配 為保證高壓水泵提供的噴射壓力恒定，驅動該液壓回路的定量液壓泵必須工作在恒轉速的額定工作狀態，噴水作業時車輛的行駛速度與路面的噴射效果有關，也是不可改變的量，所以驅動行駛的變量泵也要工作在恒轉速的額定工作狀態，行駛消耗的功率也為定值。因而，作業時需要的發動機功率為定值。 2.3新型單軸分動箱的設計 分動箱是動力分配系統的核心部分，傳統思想設計的分動箱通常采用二到三軸結構進行動力分配。本文設計的新型輕型高壓清洗車采用的底盤是五十鈴NKR55LLA 輕型底盤，用傳統結構的分動箱尺寸偏大，無法滿足尺寸要求。根據動力分配系統的特點，自主設計開發了單軸傳動的分動箱，大大減小了分動箱的尺寸，使車身結構更加緊湊。 3液壓系統 液壓控制系統是噴水作業時各個動作得以實現的關鍵，主要由變量泵、定量泵、驅動馬達、液壓缸、冷卻器、集成控制閥塊、過濾器等組成。從實現的功能上來看，液壓系統由液壓馬達驅動行走系統和液壓馬達驅動噴水系統兩個子系統組成。 3.1液壓馬達驅動行駛系統 變量泵 、液壓馬達 和相應的液壓回路構成了液壓行走子系統， 為系統的補油泵，與定量泵同軸連接。該系統由集成控制閥塊實現對油路和液壓泵的控制。變量泵及馬達的選型，基本根據前述的功率值來確定。 3.2液壓馬達驅動噴水系統 液壓馬達驅動噴水系統由定量泵 、定量液壓馬達 、水泵 、溢流閥、冷卻器、過濾器和液壓缸及疊加閥組 等組成。 為液壓缸和疊加閥組共同組成，用于控制噴水架的升降、伸縮等動作。液壓油返回油箱時，經過水冷卻器冷卻。 4水噴射系統 水系統是高壓清洗車的核心部分 主要由高壓水泵、噴水架、噴嘴、噴槍及閥等組成。水箱流出的水經水泵后將水壓提高到8MP ，形成高壓射流噴射到路面。高壓泵的合理選取，對發動機效率的最佳利用、最佳沖洗效率都有重要的影響，需要根據設計要求及發動機參數等來確定高壓泵的功率、工作轉速和泵壓等參數。水系統設計中的主要問題包括以下兩個方面。 4.1伸縮式多自由度噴水架 噴水架是噴射系統的執行機構，安裝在高壓清洗車頭部，高壓噴嘴安裝在噴水架上。為增加路面噴射沖洗的寬度，設計了新型液壓控制伸縮機構。工作時，安裝有噴嘴的兩根后排管向外伸出，與車頭前方的主噴管成一直線，同時向路面噴射高壓水流；工作完成后，后排管縮回主噴管后側。噴水架的離地高度也由液壓系統控制，同時還設計了機械式高度微調結構，對高度進行微量調節。 4.2噴水系統參數的優化 高壓清洗車的用途是清洗出優質清潔的路面，所以，如何提高路面清洗效果、節約用水是設計時需要考慮的重要問題，也是以往的研究沒有重點考慮的問題。路面清洗的效果和許多參數有關。包括噴射高度 、噴嘴的形狀、噴射的壓力、噴射角度 、射流寬度 、噴嘴擴散角 、噴嘴間距等 。通過大量的理論和試驗研究，確定了噴射高度噴射的壓力、噴射的角度、射流的寬度、噴嘴的擴散角 時，對路面進行沖洗的效果最佳，路面的洗凈率在 以上，清洗單位面積的路面所消耗的水量和能量，都達到了最佳匹配值。 5電控及操作系統設計 電控系統要實現車輛的工作狀態顯示、監測、報警和控制等功能。主要包括儀表顯示系統、儀表盤、液壓油驅動車速表盤、液壓油溫顯示、油壓顯示、水箱的水位顯示及報警、噴水管工作狀態顯示、液壓系統運行時間記錄等功能，整個系統采用模塊化設計，控制面板集成在駕駛室內適當位置，便于操作者控制操作。 水箱水量的監測和預報是電控系統的重要環節，必須嚴格控制。水箱內的水經過冷卻器為液壓油冷卻后才進入高壓水泵，所以水箱內必須有相當?shù)念A留水量。設計時采用了磁浮式液位傳感器，準確測定液位的高度。操控系統主要包括操縱箱，動力切換手柄，油驅車速踏板，左、中、右噴水管伸縮控制手柄，噴水柄前后擺動控制手柄和車速踏板。操控系統的設計，操縱箱的布置、結構，各手柄的位置，充分考慮了人機工程學要求，便于操控。 6總體結構設計 在結構上，整車包括底盤（帶駕駛室）、水箱、液壓油箱、水泵、分動箱、噴水架等大型組件。水泵和液壓油箱平行布置在駕駛室和水箱之間，左右兩側采用外擺鉸鏈式車門，開啟方便，便于維修檢查。水箱采用不銹鋼橢圓形結構，外面配有裝飾側圍及裙邊。分動箱布置在底盤內液壓油箱和水泵下部，變速器和第二傳動軸之間。整車采用Unigraphics 軟件進行三維實體設計，并采用其裝配功能進行了整車的虛擬裝配。 7 結論 新型高壓清洗車的研制，以提高路面沖洗效果和節約能源為核心，采用了單發動機配置的動力分配方式，充分發揮噴水作業時發動機的功率，提高了噴水壓力；并對路面沖洗效果的影響參數進行了優化。對動力分配系統、液壓系統、水系統、電控及操縱系統、總體結構等都進行了深入的研究。在車身外形、單軸分動箱的開發以及路面沖洗效果等研究方面申請了數項專利。本文研制的新型高壓清洗車，經過樣車試驗，各項指標都達到了預定要求。新型高壓清洗車的研制，為我國高性能高壓清洗車的自主開發，起到了良好的推動作用。