兩足行走機器人——臂部結構部分設計,兩足行走機器人——臂部結構部分設計,行走,機器人,臂部,結構,部分,部份,設計 Sensors, and Command, Control, Communications, and Intelligence (C3I) Technologies for Homeland Security and Homeland Defense V, edited by Edward M. Carapezza, Proc. of SPIE Vol. 6201, 620112, (2006) 0277-786X/06/$15 doi: 10.1117/12.666253 Proc. of SPIE Vol. 6201 620112-1 Proc. of SPIE Vol. 6201 620112-2 V Proc. of SPIE Vol. 6201 620112-3 Proc. of SPIE Vol. 6201 620112-4 Hip Actuator Flow-Load Characteristics. Supply = 3200P51 Pressure (PSI) Knee Actuator Flow-Load Characteristics. Supply = 3200P51 0 2000Pressure (PSI) 2500 Proc. of SPIE Vol. 6201 620112-5 Proc. of SPIE Vol. 6201 620112-6 Proc. of SPIE Vol. 6201 620112-7 Proc. of SPIE Vol. 6201 620112-8 62 OMFUTER SYSTEMCCUMULATORSp I -HYDEA U Lb F ILTEEANIFOLD ELOCKNEE ACTUATOE Proc. of SPIE Vol. 6201 620112-9 Proc. of SPIE Vol. 6201 620112-10 35 36 37 38 39 40 35 36 37 38 39 40 35 36 37 38 39 40 35 36 37 38 39 40 - 5 36 37 38 39 40 - 35 36 37 38 39 40 36 37 38 39 40 35 36 37 38 39 40 35 36 37 38 39 40 Proc. of SPIE Vol. 6201 620112-11 especially since it is straightforward to predict when high pressure will be required and the switches could be switched ahead of time. The potential to switch between supply pressures at high rate leads one to ponder whether a switching circuit similar to a PWM electric motor amplifier could be developed. However, there are two key requirements of PWM circuits that allow them to be efficient: high frequency switches and inductors. With an electric PWM motor amplifier, high voltage is applied momentarily through a switch to an inductive load. The inductor builds up its magnetic field and when the switch turns off, the electric field breaks down, causing current to continue flowing through the load. Since the switching frequency, typically on the order of 10 kHz, is an order of magnitude faster than the L/R time constant of the load, the current delivered to the load smoothly varies. With such a circuit, a single high voltage source can be used to efficiently drive a load with varying voltage requirements. Unfortunately, hydraulic switches are relatively low frequency, on the order of 100 Hz, and hydraulic inductors are impractical. While there is some inductance (inertia) in the hydraulic fluid itself, it is not sufficient. One could make a hydraulic inductor using for example a hydraulic motor with a flywheel, but the size and weight may be prohibitive. For high inertial loads, the mass of the load may provide the proper amount of inertia and such a technique might be practical. However, the loads present during the periods of concern for a running robot (such as leg swing) are typically very low inertia. Therefore, it is doubtful that similar techniques to PWM amplifiers can be used in hydraulic circuits unless new forms of small and lightweight hydraulic inductors and faster hydraulic switches can be developed. 7. NEXT STEPS Ongoing efforts with the Monopod include the following: Finish integrating the power system into the Monopod. Further refine the control algorithm. Investigate more efficient hydraulic system designs. 8. ACKNOWLEDGEMENTS This project was funded under TACOM SBIR contract #W56HZV-04-C-0072. Special thanks to Gill Pratt for clarifying discussions on the operation of electric PWM amplifiers. REFERENCES 1 G. A. Pratt and M. M. Williamson, Series elastic actuators, Proceedings. 1995 IEEE/RSJ International Conference on Intelligent Robots and Systems. Human Robot Interaction and Cooperative Robots, pp. 399-406, 1995. 2 J. E. Pratt and B. T. Krupp, Series elastic actuators for legged robots, Proceedings of the SPIE - The International Society for Optical Engineering, vol. 5422, no. 1, pp. 135-144, 2004. 3 D. W. Robinson, Design and Analysis of Series Elasticity in Closed-Loop Actuator Force Control. PhD. Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 2000. 4 R. M. Alexander, Three uses for springs in legged locomotion, International Journal of Robotics Research, vol. 9, no. 2, pp. 53-61, 1990. 5 M. Raibert, Legged Robots that Balance MIT Press, 1986. 6 K. Amundson, J. Raade, N. Harding, and H. Kazerooni, Hybrid hydraulic-electric power unit for field and service robots, 2005 IEEE/RSJ International Conference on Intelligent Robots and Systems, pp. 3453-3458, 2005. 7 H. Kazerooni, Exoskeletons for human power augmentation, 2005 IEEE/RSJ International Conference on Intelligent Robots and Systems, pp. 3459-3464, 2005. 8 Shin-Min Song and Kenneth J.Waldron, Machines That Walk: The Adaptive Suspension Vehicle MIT Press, 1989. Proc. of SPIE Vol. 6201 620112-12