BMW320i2.0L典雅型轎車變速器設計【寶馬320i2.0典雅型手動檔變速器的設計】【中間軸式變速器】
BMW320i2.0L典雅型轎車變速器設計【寶馬320i2.0典雅型手動檔變速器的設計】【中間軸式變速器】,寶馬320i2.0典雅型手動檔變速器的設計,中間軸式變速器,BMW320i2.0L典雅型轎車變速器設計【寶馬320i2.0典雅型手動檔變速器的設計】【中間軸式變速器】,bmw320i2,典雅,轎車,變速器
附 錄A
Automotive Transmission
J.A.smith
The role of transmission:
The output of the engine speed is very high, maximum power and maximum torque at a certain speed area. Engine in order to exert the best performance, it is necessary to have a variable-speed devices, to coordinate the engine speed and the actual wheel speed. Transmission process in the car, in between the engine and the wheels have a different gear ratio, by shifting the engine can work at their best performance of state power. Transmissions are the development trend of more and more complex, increasingly high degree of automation, automatic transmission will be the mainstream of the future.
Transmission type.
Automotive automatic transmission has three common forms: namely, Automatic Transmission (AT), mechanical stepless automatic transmission (CVT), electric-controlled mechanical automatic transmission (AMT). At present, the most widely used is the AT, AT almost become synonymous with automatic transmission.
AT Torque by Torque, and planetary gear and hydraulic control system components, through the hydraulic transmission and gear portfolio approach to achieve variable-speed torque variation. One of Hydraulic Torque is the most important parts, which pump wheels, turbines and components, such as guide pulley of the transmission of both torque and the role of clutch.
AT compared with, CVT save the complex and cumbersome combination of variable-speed gear transmission, but the two groups to carry out variable-speed drive pulley. By changing the driving wheel and driven wheel contact belt speed radius. Canceled because of gear, so the transmission ratio can change speed more smoothly, without shifting sense of the sudden jump.
AMT and Automatic Transmission (AT) are the same class has automatic transmission. It is in general based on the manual transmission, through the installation of microcomputer-controlled electric device to replace the original finish by the manual operation of the clutch of separation, joint, and block transmission of the election, motion shift, automatic shift implementation.
The general structure of automobile transmission:
1. Easy transmission of the basic structure: the shell, transmission and manipulation of some parts.
(1)Shell: Shell is the basic pieces of support for the installation of transmission and storage of all parts lubricants. Has installed its bearing on the precision boring. Transmission under varying load, so the stiffness of the shell should be enough, there is to strengthen the wall, the shape of the complex, as many castings (gray cast iron materials, commonly used HT200).
In order to facilitate the installation, transmission and manipulation of some Split parts are frequently made, cover with the housing connected by bolts and reliable positioning. Shell has come on up, I put the oil, check oil foot mouth, should also be taken into heat dissipation.
(2)Transmission parts: is the gear, shaft, bearings and other transmission parts. Geometry axis through strength, stiffness calculation. Mainly due to decide on the stiffness, while the carbon steel and alloy steel elastic modulus almost equal, so the general use of carbon steel (commonly used 45 steel). Only one gear with the shaft or axle load made serious only by steel. Shaft and gear for many spline connection (for neutral good, reliable transmission of power, a small compressive stress, etc.). Spline shaft bearing parts and let the surface hardening treatment by the Department. Shaft with rolling bearing supports many, easy lubrication, high efficiency, small radial clearance, axial positioning should be reliable. Many ways to use splash lubrication (υ> 25m / s, as long as the appropriate viscosity apparently succumbed to the wall).
(3)to manipulate parts: the main components located inside the transmission cover.
2.The composition of the structural characteristics of transmission:
there is easy and efficient transmission, the advantages of simple easy-to-use-Jun mine but a few files, i changed the scope of small (traction, speed small), file number should be taken only at certain limited Cut used. If the increase in the scope of i, then increase the size so that transmission, axle span increase, both in order to increase the file-axis span of a few do not make too large, transmission can be formed. The composition of the so-called transmission, usually from both a combination of easy transmission, one of a few more files as the main transmission, less transmission known as the deputy.
Transmission component of advantages:
(1)can reduce the number of gears, and a few more files to reduce the number of gear the more obvious advantages. Easy compared with the transmission, it can shorten the length of shaft to reduce the transmission of the external size and weight, and can easily be more than one reverse. Into the file so the current number of files more than six hours, almost all transmission components.
(2)transmission: the rate of change of Ω than large: if the main transmission gear ratio change rate Ωzu = 3, Vice transmission Ωfu = 4 is Ω = 12; easy transmission arrangement Ω = 12, the structure is often difficult to reasonable.
Composed of transmission of disadvantage:
(1)file groups have correspondence between the transmission ratio, so that each file is not 2, (the speed and traction) are ideal.
(2)manipulation of trouble shifting, and sometimes both want to manipulate some speed, if not for the flower arrangement will shift memory.
In order to reduce the control action, it is best to shift the order. Calling attention to the grade for this presentation ten out files so that the first group of transmission ratio is greater than all of the first file group 11 to the majority of phase transformation from the stall speed of just fixing the main purpose of this is the only way most convenient.
GM Hydra-Matic
General can be regarded as the founder of automotive automatic transmission has been. The world's first automatic transmission is used in the United States in 1940 Oldsmobile automobile on a common, and it is a tandem structure of planetary gear transmission fluid control. Applies to the Cadillac STS-V's latest six-speed Hydra-Matic automatic transmission 6L80, may be regarded as the world's most advanced Automatic Transmission (AT) has been.
Automatic Transmission For example, it has an internal gear is also divided, but the abolition of the clutch. The more gear, then shift, the better the ride comfort. At present, common automatic transmission are generally four-speed, that is, block has four forward. 6L80 has six forward gear, the number of teeth than the one block are separately 2.36,3 block 4.03,2 block 0.85,6 block 1.15,5 block 1.53,4 block 0.67. Obviously, it is more than 4-speed automatic transmission with a greater ratio and smaller ratio of the difference, it is more smooth when speed.
Outside the block a few more besides, 6L80 also has a lot of unique special skills:
Driver shift control system (DSC) - through its driver into a vehicle without the clutch from the automatic five-speed, high-performance. Drivers under the food stalls to the DSC on the location, the light touch can be specified at the scope of the neat, smooth implementation block addition and subtraction. The driver to switch control mode, the transmission control module monitors the vehicle speed, engine torque and gear used to decide whether to automatically add block to avoid damage to the powertrain. Each have a sliding gear on the clutch, can be carried out on all five gear engine braking.
Performance computing systems down block (PAL) - in a row after a high-speed, stop maintain engine braking. Transmission control module based on driving behavior to decide whether to activate the device. If the system found in the vehicle slowed down before turning, transmission may be even lower in order to avoid stall two block.
Performance computing shift system (PAS) - turn off the accelerator in high-speed automatic adjustment of the level of acceleration gear, re-open at throttle-down power to elevate. Once the transmission control module to detect high levels of command, this function immediately.
This transmission also reduced in the rugged mountain road "Shift Search," the stability of the shift functions, with the lower block BrakeAssist monitoring function, electronically controlled engine braking, as well as to adapt to these high-power, high torque engines are the new need a new dual-chip torque converter. In addition, SRX is also equipped with high-performance downhill Downgrade Detection Brake Assist.Chinese car market gearbox
China's auto market is in a transmission period of rapid development. 2007 Chinese sales of 8,791,500 motor vehicles, motor vehicle production in 2008 will exceed nine million sales, car sales in 2010 will reach 12.63 million. Size of the market in the automotive industry's rapid growth, China is faced with a major transmission industry opportunities. In 2006 the market scale of China's automobile transmission up to 300 billion yuan and more than 20% annual growth is expected in 2010 is expected to reach 60 billion yuan.
附 錄B
汽車變速器
J.A.史密斯
變速器的作用：
發動機的輸出轉速非常高，最大功率及最大扭矩在一定的轉速區出現。為了發揮發動機的最佳性能，就必須有一套變速裝置，來協調發動機的轉速和車輪的實際行駛速度。變速器可以在汽車行駛過程中，在發動機和車輪之間產生不同的變速比，通過換擋可以使發動機工作在其最佳的動力性能狀態下。變速器的發展趨勢是越來越復雜，自動化程度也越來越高，自動變速器將是未來的主流。
變速器的型式：
汽車自動變速器常見的有三種型式：分別是液力自動變速器 (AT)、機械無級自動變速器(CVT)、電控機械自動變速器(AMT)。目前應用最廣泛的是AT，AT幾乎成為自動變速器的代名詞。
AT是由液力變扭器、行星齒輪和液壓操縱系統組成，通過液力傳遞和齒輪組合的方式來實現變速變矩。其中液力變扭器是最重要的部件，它由泵輪、渦輪和導輪等構件組成，兼有傳遞扭矩和離合的作用。
與AT相比，CVT省去了復雜而又笨重的齒輪組合變速傳動，而是兩組帶輪進行變速傳動。通過改變驅動輪與從動輪傳動帶的接觸半徑進行變速。由于取消了齒輪傳動，因此其傳動比可以隨意變化，變速更加平順，沒有換擋的突跳感。
AMT和液力自動變速器(AT)一樣是有級自動變速器。它在普通手動變速器的基礎上，通過加裝微電腦控制的電動裝置，取代原來由人工操作完成的離合器的分離、接合及變速器的選擋、換擋動作，實現自動換擋。
汽車變速器一般結構：
1．簡單式變速器的基本結構：由殼體、傳動部分和操縱部分組成
(1)殼體：殼體是基礎件，用以安裝支承變速器全部零件及存放潤滑油。其上有安裝軸承的精確鏜孔。變速器承受變載荷，所以殼體應有足夠的剛度，內壁有加強，形狀復雜，多為鑄件(材料為灰鑄鐵，常用HT200)。
為便于安裝，傳動部分和操縱部分常做成剖分式，箱蓋與殼體用螺栓聯接并可靠定位。殼體上有加油、放油口，油面檢查尺口，還應考慮散熱。
(2)傳動部分：是指齒輪、軸、軸承等傳動件。軸的幾何尺寸通過強度、剛度計算確定。因主要決定于剛度，而碳鋼與合金鋼彈性模量近乎相等，所以一般用碳鋼(常用45鋼)。只有齒輪與軸制成一體或軸載荷嚴重才用合金鋼。軸與齒輪多為花鍵聯接(對中性好，能可靠傳遞動力，擠壓應力小等)。軸的花鍵部分和放軸承處經表面淬火處理。軸多用滾動軸承支承，潤滑簡單，效率高、徑向間隙小，軸向定位應可靠。潤滑方式多用飛濺(υ>25m/s，只要粘度適宜可甩到壁上)。
(3)操縱部分：主要零件位于變速器蓋內。
2．組成式變速器結構特點
簡單式變速器有效率高、構造簡單使用方便鈞優點礦但檔數少，i變化范圍小(牽引力、速度范圍小)，只宜在檔數不多的某些車工采用。若增加i的范圍，則使變速器尺寸加大，軸跨度增加，為了既增加檔數又不使軸跨度過大，可采用組成式變速器。所謂組成式變速器，通常由兩個簡單式變速器組合而成，其中檔數較多的稱為主變速器，較少的稱為副變速器。
組成式變速器的優點：
(1)可以減少齒輪個數，而且檔數越多減少齒輪個數的優點愈明顯。同簡單式變速器相比，它可縮短軸的長度，減少整個變速器的外部尺寸和重量，并且能方便地得到不止一個倒檔。所以當前進檔數超過六個檔時，幾乎都用組成式變速器。
(2)傳動比變化率Ω大：若主變速器傳動比變化率Ωzu=3，副變速器Ωfu=4則Ω=12；若使簡單式變速器Ω=12，結構往往很難合理。
組成式變速器的缺點：
(1)檔組間傳動比有對應關系，不易使每檔的(速度及牽引力)都很理想。
(2)換檔操縱麻煩，有時要操縱兩個變速部分，若為插花換檔還不便記憶。
為了減少操縱動作，最好能順序換檔。為此要求重視檔次編排使第10檔組傳動比全部大于第11檔組，達到多數相領排檔的變換只需操縱主變速的目的，這樣才最為方便。
通用 Hydra-Matic：
通用可稱得上是汽車自動變速器的鼻祖了。世界上第一個自動變速器就是1940年應用在美國通用的奧斯莫比爾汽車上的，它是一臺串聯式行星齒輪結構的液控變速器。而應用于凱迪拉克 STS-V的最新Hydra-Matic六速自動變速器6L80，則可稱得上是世界上最先進的液力自動變速器(AT)了。
對于液力自動變速器來說，它的內部其實也有擋位之分，只是取消了離合器。擋位越多，則換擋的平順性就越好。目前常見的自動變速器一般都是四速的，即有4個前進擋。6L80則有6個前進擋，齒數比分別是1擋4.03、2擋2.36、3擋1.53、4擋1.15、5擋0.85、6擋0.67。顯然，它比4速自動變速器具有更大的速比和更小的速比級差，因此變速時也就更加平順。
除了擋數更多以外，6L80還具有很多獨有的特殊絕技：
駕駛換擋控制系統(DSC)—通過它，司機將車輛從自動擋變成無需離合器的高性能五速手動擋。司機把排擋桿推到DSC位置上后，輕輕一碰就可以在指定的范圍內利落、流暢地實現加減擋。在司機切換控制狀態下，變速器控制模塊會監控車輛的速度、發動機扭力以及所使用的擋位來決定是否自動加擋，避免對動力總成造成破壞。每個擋位上都有滑行離合器，能在所有五個擋位上進行發動機制動。
性能運算降擋系統(PAL)—在連續高速行駛后，阻止升擋，保持發動機制動。變速器控制模塊根據駕駛行為來決定是否啟動這一裝置。如果系統發現車輛拐彎前速度下降，變速器可能會連降兩擋以避免失速。
性能運算換擋系統(PAS)—它在關閉油門高速水平加速時自動調節擋位，在油門重新打開時降擋迅速提升動力。變速器控制模塊一旦察覺高速水平指令，這項功能立即啟動。
這款變速器還有在崎嶇山路上減少“擋位搜索”的換擋穩定功能，帶有制動助力的降擋監視功能，電控發動機制動，以及適應這些高動力、高扭力的新式發動機所需的新型雙片式扭力變換器。另外，SRX還配備了性能卓越的Downgrade Detection下坡剎車輔助系統。
中國汽車變速器市場：
中國汽車變速器市場正處于高速發展期。2007年中國汽車銷售879.15萬輛，2008年汽車產銷量將突破900萬，2010年汽車銷售規模將達到1263萬輛。在汽車行業市場規模高速增長的情況下，中國變速器行業面臨著重大機遇。2006年我國汽車變速器市場規模達300億元人民幣，并且以每年超過20%的速度增長，預計2010年有望達到600元。
9
收藏