縱軸流式水稻聯合收割機脫離系統結構設計,縱軸流式水稻聯合收割機脫離系統結構設計,縱軸,水稻,聯合收割機,脫離,系統,結構設計 Long inefficient harvester maintenance A "prevent long inefficient combine threshing not clear, Threshing was unclear, or after threshing crops are still left on a certain number of grain crops, or fails to retain the original threshing, and the corn longer branch, etc. It is among the most common of combine harvesters. How to prevent threshing, the method is as follows: 1 and the harvest should keep linear assignment. Can easily otherwise, driving crop harvest threshing clarity is messy effect. 2, should maintain threshing tooth thickness of unilateral not less than 2.5 mm. Otherwise, must change surface or update. Threshing tooth crest and inherit the gap should keep on net 3-5mm. Excessive threshing will influence, to adjust. 3, often keep cutting grass the keenness of the sword. Cut grass by the side of the sword blade surface should be timely change wear or update. For grain threshing clean and create good conditions. 4 the conveyor chamber, threshing and guide the clearance should be within 2mm - 0, too, should be adjusted translocated cannot enter threshing room. 5, threshing depth is deep, not often adjust the threshing clarity of circumstances, should maintain proper depth, in order to reduce indoor embroiled in a threshing long stalk. 6 and when the throttle should be put in the harvest, make maximum revs turned in every minute of 2000. Otherwise it will affect threshing effect. If found speed should be promptly dropped out, reduce the load inspection. 7 and the crop growth, the field should be adopted, reduce speed reduced cut to reduce the load, enhance the threshing performance. Eight, the situation is unfavorable harvest: crops 55cm length less than poor too low, mechanical, crops have large difference, length of maturity, crop crop varieties of wet, difficult threshing. 2 the long inefficient safe operations of rice harvester Combine widely applied in rural areas, with the popularization of long inefficient combined harvesters, strengthen the safety production to prevent accidents, agricultural machinery safety supervision has become an important content of the work. JiShou is an important guarantee of economic benefit, therefore, must pay attention to the safety operation, the method is as follows: 1, have qualified operation skills. Operators must attend technical training, familiar with and understand the performance, structure, the machines use, maintenance and operation mastering skills. Qualified through examination before operation. 2, to observe the safety regulations. The safety instructions carefully study buyers on homework instructions and combine all sorts of safety warning labels. 3 and safety clothing. Wear comfortable clothes, prohibit wearing headscarves, scarves, safe operations against the slippers etc. 4 and security. Abide by traffic rules. Ban on others, pack accessory, avoid teasers, through the dam, could be JiGengLu culvert and etc, and can withstand prior to confirm unit weight, not pushy. 5, safety and loading trucks. The ground must be flat hard, loading and unloading board must have enough strength, width, length and antiskid device and hook. Two parallel plates should be no difference, low slow. Midway cannot turn, speed and braking lest overturned, if need to be modified direction return to sender. 6 and safety operation. Harvest Operators should be energetic, lack of sleep, drunk or illness of unfavorable operation. In the homework before pack good safety cover, shields, and try running shell, confirm the working parts may be put into operation. The machine before must honk or other methods to meet food and signaled that it is safe to those around. In the work, listen to observe, once produce abnormal shall immediately stopped running, promptly components. 7 and safety inspection and maintenance. Harvesters in machine cleaning machine, check and adjustment should be shut out fault, when the shift lever, and for the engine should be separate each clutch. In the harvest, when should be raised overhaul safety devices will be locked or cut machine with reliable supporting things fixed, prevent the harvest of decline. 8 and prevent fires. Should be on fire, fuel and oil spill to timely rub-up. Engine exhaust and battery, not allow heads up around the machine can park in the stalk of place. And no smoking. 9 and prevent burns. The engine running or just stop immediately when cannot open cooling box, prevent water jet scald, subject to open after cooling. 10 and safety parked. Harvesters will reap should be parked down to the ground of the lowest positions, or shut, take out the key step, engine braking under fixed, the pavement in tyre shall be put on the track or before anti-skid pad. 3 the long inefficient to prevent cut sets jams rice harvester, Cutting machine is blocked in the operation of the combined harvester ommon fault, it tends to affect the normal operation of the harvester. Serious when cut machine can't work. Therefore must pay attention to the prevention work cut machine, clogging the method is as follows: 1, harvest crops cannot be dry, wet, and dew. Crops in height, otherwise easily 55mm crop uprooted, clogging the chain, but also stem not threshing. Lodging should comply with the Angle of cut in 85 degrees below 70 degrees in reverse, cut the following requirements. Harvest the crops to make excessive lodging cutting machine jam. At harvest time, reduce should reduce cutting speed, watch, found that jam. Timely parking 2, the harvest should as far as possible to stay straight road. To make points bending because of grain harvest stem the grass points over the crops, and deformation when conveying grain crops is messy, clogging. 3 and reasonable control the feeding amount reap crops. Such high crop harvest shall be taken, reduce speed reduced cut, avoid excessive loads caused jams. After the collision stacks points should be timely deformation is restored to the correct width, prevent excessive width caused by feeding amount caused jams increase. 4 should keep a sharp, sticking. Every day after harvest should remove dirt, weeds, check and adjustment, promptly replace worn sticking. Keep moving knife knife and set the gap in 0 ~ 0.5 mm. 5, help to maintain good grain chain tensioner degrees. And grain, grain and stent shall promptly replace after wearing claw back to ensure crops not messy. 6 and often keep claw chain belt, bluegrass, shoot, the chain chain, depth in such a state, too loose when should adjust, excessive wear should be replaced. 7 and cutting machine jams cannot use accelerated forced through. So easily make driving components are damaged. The correct approach is rapid, using artificial clear the blockage of crops. 4 the long chain transmission inefficient rice harvester maintenance" Chain transmission is indispensable to combine the transmission mechanism. It's work or harvesters will directly affect the normal work of the components and performance, and therefore should be done in use, maintenance and repair the method is as follows: 1 in shaft, wheel should be no skewed and swinging. In the same transmission components in the face of two sprockets should be located in the same plane and sprocket center distance 0.5 meters in the allowable deviation, 1 mm, Sprocket 0.5 meters above centre distance in the allowable deviation, 2 mm. But does not allow to have the friction sprocket teeth profile phenomenon, if two rounds of migration to produce large chain and accelerate wear off. In the replacement of sprocket, we must pay special attention to check and adjustment offset. 2, the chain of firmness should fit, too tight increase power consumption, bearing wear, Too loose easily beat and chain chain. Chain of chain for: from central filed or press, two sprockets centre distance is about 2-3cm. 3, a new chain or long after the use to adjust, can elongation, to look for the chain, but must be even. The chain should lock plate, back through the chain is inserted in the outside, lock piece at the turn of the mouth should be in the opposite direction. 4 and sprocket badly worn, should also change new sprocket and new chain, in order to ensure good engagement. Not only change the new chain or new single chain. Otherwise it will cause a new chain or improperly meshed accelerate new sprocket and wear. Sprocket tooth surfaces wear to a certain degree in turn use (used to face adjustable sprocket). In order to prolong the using time. 5, old and new chain chain can use, otherwise easy mixed in transmission chain, tensile impact. 6, chain in work should promptly fill lube. Oil must enter roller and set in the fitting clearance, improve the working conditions and reduce wear. 7 and when the machine, long-term storage chain should be removed using kerosene or diesel clean, then coated with oil or butter in a dry place, to prevent corrosion. 5 the long inefficient rice harvester inter-district assignments need attention" As a long inefficient (KUBOTA) combine professional harvest, 28% of homework is quite important. To smoothly inter-district harvest, please users must be attached to the following aspects of work. 1 the preparation before operation, and develops (1) inter-district assignment information collection. Users can according to relevant state departments of information throughout the wheat and rice harvest and local agricultural information management, also may follow contact with customers, because the harvest of the local conditions are familiar with the user. (2) business contacts. On-the-spot investigation in the field conditions, crop growth and high price, etc. (3) inter-district homework route. According to the time sequence of all crops, choose as far as possible, set harvest security conditions are good, traffic is convenient. (4) machine. In order to avoid failure inter-district assignments must be done before operation expenses in inter-district before repair, comsumption products, oil etc. Such as engine oil, inferior oil market, many in the local time before to 28% of purchase. Hara& Co. inefficient (5) and vendors. Homework, route will inter-district inform vendors, carry on with the certificate (the combine harvester driver's license and id card of 28%, etc.). (6). Try to purchase related (machine, personnel) insurance. 2 and develops in the homework problems that should be paid attention to (1) harvest in the operation, to avoid attention combining exertion caused by accidents due to overwork. (2) strengthen the maintenance and inspection machine, the machine always in good working condition. (3) to strengthen the supervision of machine, storage, especially to avoid machine weathered and guard against theft, prevent damage. 3 and the handling problems Such as: (1) in the inter-district assignments harvesters malfunction, please come and maintenance service, will contact details (including harvesters fault fault components, harvest field around), damaged parts, and quantity (shows a part of components in place, serial number part), the specific location and harvesters telephone users such report maintenance personnel. (2) if you want to buy parts, can contact with long inefficient local hara& Co., company address (spare parts purchase, etc.) should be near. If you cannot buy accessories, direct contact with the seller, to discuss the required parts orders and shipping method, in the shortest possible time after receiving accessories, maintenance, continue to work. 6 the maintenance long inefficient rice harvester of unidirectional clutch, The function is a one-way clutch combine harvester in advance when the power of the engine reliably transfer to combine harvester, fall off quickly, in order to realize the need of combine harvesters. In use due to improper operation, easy cause one-way clutch early wear, harvesting machine doesn't work well. Therefore, must grasp the correct use of method. 1 and the drive belt should reap department regularly or adjustment, the length of a spring in 102mm, cannot too loose or too tight. Or should adjust the length of the spring. 2 and combine in operation should be done in the stable power, speed, smooth junction stable steering, must not stop, accelerated, steep, hurry to, in order to reduce the shock load one-way clutch. 3 and in harvest in the homework assignments to observe the harvest, cutting machine, jams that immediately after stopping harvesting clutch, separated by artificial clear all the progress of begin again after operation. Do not remove or not in blocking incomplete remove junction, clutch, so easily to harvest early damage of unidirectional clutch. 4 and reasonable control the feeding amount reap crops. When high-yielding crop harvest if should be taken to cut, reduce speed reducing excess load in order to reduce the one-way clutch. After the collision stacks points should be timely deformation is returned to the correct width, in order to prevent excessive width caused by feeding amount caused jams increase. 5 and the harvest of lodging crops can not force (85 degrees below for the cut and thrust to 70 degrees Celsius) cut. Lodging crops are messy, should be adopted in the harvest threshing depth, using automatic control, find out timely downtime clogging. 6 and one-way clutch after damage replace. In the first should check whether the axis wear is a one-way away when the diameter of the axis wear to 18.771 mm, must change the new axis, otherwise the new one-way clutch after loaded still cannot play a role. Wheel organization function is supporting the full weight of combine harvesters, driving and harvest, it is the important system combines walking working parts. If not for the correct use and operation, maintenance, easily wheel organization early wear. Therefore must pay attention to early wear prevention. The method is as follows: 1, to strengthen the wheel organization daily maintenance. Do homework after stent to load, timely, lifting, tensioner arm sticky roller and mud product, clean weed. 2 and constant observation wheel load, wheel, lifting, tensioner wheel rotation condition videotapes. Find abnormal or wheel rotation, should not carefully, change bad parts, hidden faults. 3, check the quantity, truck wheels lubricant should be added to the shortage of oil. Provisions Find duo-cone floating oil, should change in time to maintain good sealing. 4, truck wheels, stents, lifting, tensioner wheel rim thickness should have worn thin change in time, otherwise caused by insufficient strength variant rupture, scrape. 5 and driving wheel wear a tooth thickness 5mm amounted to face when using, adjustable to prolong the using life. When both tooth thickness should be promptly replace worn, otherwise it will cause sprocket and track core iron meshing impact when increases, abnormal wear iron core, serious when still can hook iron core. 6 500 hours, each work regularly to walk round institutions should be thoroughly checked, repair, to achieve good technical conditions. 7 and combine in road, should avoid bad roads in the road. When the crawler bottom to have cleared eyewinker. Ensure the wheel in good working environment, improve its service life. Long inefficient combine the good crop harvest lodging with benign. Under normal circumstances can harvest the crops for lodging 85 degrees below, cut cut in inverse 70s. At harvest time must pay attention to grasp the operation method under: 1, should use a sharp knife sticking the sword, and the gap shall be in 0 ~ 0.5 mm. 2 stacks, claws should be adjusted to height can lift crop panicle position (namely the position on a standard). To straighten up, reduce crop messy. 3 stacks, and shall be transferred to "high speed", and to increase the help shift position for lodging, grain number of grain crop rotary. 4, harvest of transmission belt, shoot the chain chain, ear grain, should according to regulations chain tensioner, cutting machine is too loose in the harvest clogging. 5, conveying chain tightly guide if wear, should adjust guide and chain of zero clearance, crop is involved, or within the cylinder threshing. 6 and the cleanness of threshing regulating handle should be put on "open" position, to minimize threshing room load. 7 and the cutting grass threshing indoor dao should be promptly replace, sharp. In order to ensure the clarity, reduce crop threshing damage grain. 8 and cut in assignments platform height should keep in grain from the ground height is about 20mm. High grain can help claws, cannot fulfill the harvest. Low is easy to root crops, accelerate uprooted sticking. 9 and cut width should with slightly less than normal cut width for good (usually right portion of the grain open about 200 ~ 250m m). To alleviate the harvest of load. 10 and should adopt the automatic control of threshing depth, unfavorable adjustment. To minimize threshing room load. 11 and the harvest of straight road, don't be keep swinging. Slow speed is not reap, jam in case. In December, when the harvest to observe operation condition, should take the first right ahead and grain threshing depth, device runs into the entrance of threshing chain and watching the sequence of operations. According to the circumstance timely adjust speed, cut width harvest threshing machine, cutting height, etc, in order to maintain good depth of operation condition. 13, is not in conformity with the harvest of crops, otherwise not forced to wear, and early machine crop waste is serious. 7 the combine harvester threshing rice for the inefficient maintenance" 1, threshing room can overload in the harvest, when high-yielding crop and speed of cutting should reduce and control the work load of the rated load operation, to prevent excessive threshing chamber of the causes. 2, the harvest threshing due to lodging crops into the room to increase many weeds in the chamber pressure and threshing threshing adopts the automatic control, depth to reduce indoor excessive threshing straw into. 3, correctly use the regulating handle gib threshing. When lodging at harvest crops, the regulating handle on the open position, make indoor crop threshing, reduce indoor quickly. In the threshing, grain on the small branches shall handle is placed in position, extend the time on threshing indoor crops, increase grain clarity. Usually handle position should be put in standard. 4 and keep cutting grass blades, check the knife cut grass threshing indoor wear and abrasion can make crops or not cut off, retention time long, threshing ungodliness, threshing chamber pressure increases, cut grass dao in reversing or update after wear. 5, conveying chain tightly compressed guide, if be the clearance of crops to easily, cause stress in threshing room greaten, must always keep checking and adjusting, chain and guide the gap with zero. Six, in use as threshing shall, when close room blocked out, after the progress of the engine can work, or forced work to cause damage to the threshing room components. 8 the long inefficient rice harvester crawler maintenance instructions" Rubber pedrail are self-contained combine the important parts in the mechanism, and the price is expensive. Rubber pedrail life depends in large part on work environment and method of use. Must attach importance to the early wear rubber pedrail prevention. The method is as follows: (a), pay attention to the work environment 1, rubber pedrail, diesel engine should be avoided and various oil, grease, etc. Also should avoid with acid, alkali, salt, pesticide, and other chemicals. In this case. Clean, 2, rubber pedrail should avoid the rocks, in sharp steel etc uneven road. When necessary, can be laid wood or other flat object. 3, rubber pedrail should avoid in gravel and gravel road surface are long. This is caused extremely easily rubber surface early wear, if the driving distance, should use loaded vehicles. (2), master correct usage 1, r