變壓器墊板沖壓工藝及模具設計【硅鋼片鐵芯】【E墊片】【鐵心片】【山型墊片】【沖孔落料復合?！?/h1>
變壓器墊板沖壓工藝及模具設計【硅鋼片鐵芯】【E墊片】【鐵心片】【山型墊片】【沖孔落料復合模】,硅鋼片鐵芯,E墊片,鐵心片,山型墊片,沖孔落料復合模,變壓器墊板沖壓工藝及模具設計【硅鋼片鐵芯】【E墊片】【鐵心片】【山型墊片】【沖孔落料復合?！?變壓器,墊板,沖壓,工藝,模具設計,硅鋼片,墊片,鐵心
變壓器墊板沖壓工藝及模具設計
摘 要
本設計的題目為變壓器墊板沖壓工藝及模具設計,體現了薄板類沖裁零件的要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了本人沖壓模設計的基礎知識，為設計更復雜的沖壓模具做好了鋪墊和吸取更深刻的經驗。
本設計運用沖壓成型工藝及模具設計的基礎知識，首先分析了沖裁件的沖壓工藝性，為確定沖裁工藝方案做好了準備；然后計算沖裁力和模具刃口尺寸，便于選取壓力機及確定工作零件的尺寸和結構；最后分析了制件的特征，確定模具的設計參數、設計要點及推件裝置的選取。
本沖裁件上孔為規則形狀的孔,為了便于沖孔凸模的加工，所以在設計時把沖孔凸模設計成直通式,然后,將其鉚接在凸模固定板上。此外,該制件的尺寸較大,為保證凹模的加工精度,在設計時應將其設計成凹模組件。為了方便制件的取出，本副模具采用倒裝結構形式,同時,為了簡化模具結構采用彈性推件裝置。
關鍵詞 沖壓模,倒裝復合,凹模組件,彈性推件
EVAPORATOR BACK PLATE RAMMING CRAFT AND
MOLD DESIGN
ABSTRACT: The title of the design for lining stamping process and die design, reflects the type of sheet metal stamping parts requirements, content and direction of the design of a certain significance. Parts of the mold through the design, I have further strengthened the foundation for stamping die design knowledge, for the design of more complex stamping die to do a good job of paving the way and learn from the experience even more profound.
The use of the design process and die stamping forming the basis of design knowledge and analysis of the first blanking of the stamping process, to determine blanking of the programme prepared for and then calculating punching power and size Die Cutting Edge, For selected press and determine the size and structure of parts of the last parts of the characteristics of the design parameters established mold, design features and pushing the select pieces of equipment.
Blanking of the rules on the shape of the non-hole hole, in order to facilitate the processing punch punching, punching in the design of the punch designed as a straight-through processing, and then, riveting in its punch fixed board. In addition, the larger the size of the parts, to ensure the accuracy of processing die, the design should be designed to die components. To facilitate the removal of parts, the Vice-use flip-die structure, at the same time, in order to simplify the structure adopt a flexible mold push pieces of equipment.
KEY WORDS: stamping die, flip-composite, die components, flexible pieces of pushing
2