大眾途觀三軸六檔變速器設計【三維CATIA】,三維CATIA,大眾,途觀三軸六檔,變速器,設計,三維,CATIA 哈爾濱工業大學華德應用技術學院畢業設計 摘要 變速器是汽車傳動系統中重要的部件，主要用來改變發動機傳到驅動輪上的轉矩和轉速，它設計的好壞直接影響到汽車的實際使用性能。本文參考現有變速器參數資料的基礎上進行一定的改進，說明了汽車變速器的設計計算過程，主要內容是參數的選擇和所選零件參數的校核。 　　本文敘述了機械式變速器的功用、要求，在已提供的設計參數基礎上，通過計算分析確定結構方案和主要參數。說明了變速器主要參數的確定方法、齒輪的幾何計算和校核過程、軸的尺寸確定和校核過程和同步器的選用方法。 　　汽車變速器是通過改變傳動比，改變發動機曲軸的轉拒，適應在起步、加速、行駛以及克服各種道路阻礙等不同行駛條件下對驅動車輪牽引力及車速不同要求的需要。 關鍵詞: 變速器;傳動機構;齒輪;離合器;傳動比 Abstract Transmission System is the most important automotive components, mainly used to change the engine driving wheel on the spread of torque and speed, it’s designed to have a direct impact on the actual use of motor vehicles. In this paper, reference information on the existing transmission parameters on the basis of certain improvements on the vehicle transmission design and calculation process, the main contents of the parameters of choice and selected parts of the parameters check. This paper describes the function of mechanical transmission, requested that the provision has been on the basis of the parameters, determined by calculating the structure of the programme and the main parameters. Description of the main parameters of transmission methods, the geometric computing gear and checking process, the shaft size and the identification and verification process for the selection method of synchronization. Calculation includes gear strength, the axis of mild stiffness Automobile transmission is by changing the transmission ratio, the engine crankshaft in turn refused to change and adapt at the start, acceleration, road traffic and to overcome the obstacle of different driving conditions and speed of the drive wheel traction with different demands and needs. Key words: transmission; transmission; gear; clutch; transmission ratio 目 錄 摘要..............................................................................................................I Abstract...............................................................................................................II 第1章 緒論.................................................................................................1 第2章 機械式變速器的概述及其方案的確定..........................................3 2.1 變速器的功用和要求.................................................................3 2.2 變速器結構方案的確定.............................................................3 2.2.1變速器傳動機構的結構分析與型式選擇.........................3 2.2.2.倒檔傳動方案...................................................................8 2.3變速器主要零件結構的方案分析.........................................9 2.3.1齒輪型式............................................................................9 2.3.2換檔結構型式....................................................................9 第3章 變速器主要參數的選擇與主要零件的設計................................12 3.1 變速器主要參數的選...............................................................12 3.1.1 檔數和傳動比.................................................................12 3.1.2 中心距........................................................................ ....14 3.1.3 軸向尺寸.........................................................................14 3.1.4 齒輪參數........................................................................ 15 3.2各檔傳動比及其齒輪齒數的確定.............................................16 3.2.1確定一檔齒輪的齒數.......................................................16 3.2.2確定常嚙合齒輪副的齒數...............................................16 3.2.3確定其他檔位的齒數.......................................................17 3.2.4確定倒檔齒輪的齒數...................................................... 17 3.3 齒輪變位系數的選擇...............................................................17第4章 變速器齒輪的強度計算與材料的選擇....................................,...19 4.1齒輪的損壞原因及形式............................................................19 4.2 齒輪的強度計算與校核...........................................................19 4.2.1齒輪彎曲強度計算..........................................................19 4.2.2 齒輪接觸應力.................................................................20 第5章 變速器軸的強度計算與校核.......................................................24 5.1變速器軸的結構和尺寸............................................................24 5.1.1軸的結構..........................................................................24 5.1.2確定軸的尺寸..................................................................24 5.2 軸的校核..................................................................................25 5.2.1第一軸的強度與剛度校核.................................................25 5.2.2第二軸的校核計算............................................................26 第6章 變速器同步器的設計...................................................................29 6.1 同步器的結構......................................................................... ...29 6.2 同步環主要參數的確定.............................................................39 6.2.1同步環錐面上的螺紋槽.....................................................39 6.2.2錐面半錐角....................................................................30 6.2.3摩擦錐面平均半徑R..........................................................30 6.2.4錐面工作長度b.................................................................31 6.2.5同步環徑向厚度................................................................31 6.2.6鎖止角............................................................................31 6.2.7同步時間t.........................................................................31 第7章 變速器的操縱機構.......................................................................33 結論..........................................................................................................34致 謝.................................................................................................. .....35參考獻........................................................................................................36 - IV -