資源目錄里展示的全都有，所見即所得。下載后全都有,請放心下載。原稿可自行編輯修改=【QQ：401339828 或11970985 有疑問可加】 Introduction to Locmotive A locomotive is a railway vehicle that provides the motive power for a train,and has nohy detached from their trains, are known as power cars. Traditionally,locomotive hual their trains. Increasingly common these days in passenger service is push-pull operation,where the locomotive push the trains in one direction and are controled from a control cab at the opposite end of the train in the other. Beniefits of locomotives There are many reasons why the motive power for trains has been traditonally isolated in a locmotive,rather than is self-propelled vehicles.these include: Ease of maintenance – it is easier to maintain one locomotive than many self-propelled cars. Safety – it is often safer to locate the train’s power system away from passenger. This was particularly the case for the steam locomtive,but still has some relevance. Easy replacement of motive power – should the locomotive break down, it is easy to replace it with a new one . Failure of the motive power unit does not require taking the whoole train out of service. Efficiency – idle trains do not waste expensive motive power resources. Separate locomotives mean that the costly motive power assets can be moved around as needed. Obsolescence cycles – separating the motive power from the payload-hauling cars means that either can be replaced without affecting the other. At some times, locomotive have become obsolete when their cars are not, or vice versa.. Electric Locomotives The electric locomotive is supplied externally with electric power, either through an overhead pickup or through a third-rail. While the cost of electrifying track is rather high, electric trains and locomotives are significantly cheaper to run than diesel ones, and are capable of superior acceleration as well as regenerative braking, making them ideal for passenger service in densely populated areas. Almost all high speed train systems(e.g..IEC,TGV, bullet train) use electric power, because the power needed for such performance is not easily carried on board. Fot example the most powerfu electric locomotives that are used today on the channel tunnel freight services use 7Mwatts of power. The first known electric locomotive was buit by a Scotsman, Roert Davidson of Aberdeen in 1837 and was powered by galvanic cells. Modern electric locomotive range from small battery-powered machines for use in mines to large main-line locomotives of 6,000 horsepower(4.5MW) or more. In reality most modern locomotives are electricaly driven. Pure electric locomotives take their electrical supply from an external source while diesel-electric locomotives carry their own generating station. Main line electric locomotives first appeared at the beginning of the 20th century.The reason for their introduction was the problem of smoke, especially in tunnlels caused by steam locomotives. In the UK this was the London underground system while in the USA, it was under river tunnles and needs to eliminate smoke in built up areas. Early electric locomotives all relied on external power sourcing. Once up and running they tend to be reliable and efficint, but the supply infrastructure is a large capital expense that does require ongoing maintenance. For this reason only heavily used lines could justify electrification. For suburban lines the reduction in pollution from steam locomotives was a benefit all were aware ofl The world speed record for a wheeled train was set in 1990 ba a French TGV which reached a speed of 515.3km/h (320mph). While recently designed electrififed railway systems invariably operate on alternating current, many existing direct current sytems are still in use –e.g. in South Africa,Spain,and the United Kingdom(750v and 1500v); Netherlands(1500v); Belgiu, Italy, Poland (3000 v), and the cites of Mumbia and Chicagio (which will be switched to AC by 2025). Early locomotives came in a variety of forms. Generally they were designed to run off the supplied current. so locomotives with a direct current (DC) supply had DC motors while a alterntating current(AC) supplied locomotives with AC motors. AC can be either single or three phase. While the former requies two wire supply, one overhead the other being the track, three phase require three supply wire.Three phase locomotives therefore had two overhead supplies,the track being the third. DC supplies were either overhead or by means of a track level supply, commonly called the third rail. AC traction motors tended to be smaller than DC motors. This often meant electric locomotives with steam engine type cranks. DC motors could be smaller and set up to drive the axles.usually through a gear ,but in some early examples by being part of the axle. Even so, some notable DC electric locomotives had large DC motors driving large driving wheels. One possibility with electric locomotives is that the motor can be used as a generator during braking, feeding electricity back into the supply system; this is called regenerative barking. This is not a new idea, it was one reason for the adoption by some railways of 3 phase AC suppies. Especially in mountainous aresa where the locomotive going down would generate much of the suppy for a locomotive going up. The Swiss railway uses the system; three modern locomotives heading downwards generate enough power to power a single locomotive in its upward journey. Today all eclctric locomotives tend to have drive motors close to the axles, although some still have the motor in the body driving the wheels through internal drive shafts. Modern solid state electrical control systems means the motor does not need to match the supply. This meams multi-voltage cross border locomotives are now quite common. Drive motors are generally DC, but there are 3 phase motors on some locomotives. A small number of electric locomotives can also operate off batery power to enable short journeys or shuting to occur on non-electrified lines or yards. Pure battery locomotives also found usage in mines and other underground workings where diesel fumes or smoke are not safe aand where external electricity supplies could not be used. Battery locomotives are also used on many underground railways for maintenance operations as they are required to operate in areas where the electricity supply has been temmporarily disconnected.. Parts of Electric Locomotive Awynchronoux Motor Modern traction motor type using three phase AC electrical supply and now the favoured deisgn for modern train traction systems . Can be used on DC and AC electrified. railways with suitable control electronics and on diesel-electric locomtives. Axle Brush The means by which the power supply ciruit is completed with the substation once power has been drawn on the locomotive. Current collected from the overhead line or third rail is returned via the axle brush and one of the running rails. Battery All trains are provided with a battery to provide start up current for supplying essential circuitts, such as emergency lighting ,when the line supply fails. The battery is usually connected across the DC control supply circuit. Circuit Breaker An electric train is almost always provied with some sort of circuit breaker to isolate the power supply when there is a fault, or for maintenance. On AC systems they are usually on the roof near the pantograph. There are two types-the air blast circuit breaker and the vacuum circuit breaker or VCB. The air or vacuum part is used to extinguish the arc which occurs as the two tips of the circuit breaker are opened. The VCB is popular in the UK and the air blast circuit breaker is more often seen on the continent of Europe. Converter Generic term for any solid state electronic system for converting alternating current to direct current or vice versa. Where an AC supply has to be converted to DC it is called a rectifier and where DC is converted to AC it is called an inverter. The word originated in the US but is now common elsewhere. Cooling Fans To keep the thyristors and other electronic power systems cool, the interior of a modern locomotive is equipped with an air management system, electronically controlled to keep all systems operating at the correct temperature. The fans are powered by an auxiliary inverter producing 3-phase AC at about 400 volts. DC link Used on modern electronic power systems between the single phase rectifier and the 3-phase inverter. It is easier to convert the single phase AC from the overheak line to the 3-phase required for the motors by rectifying it to DC and then inverting the DC to 3-phase AC. Inverter Electronic power device mounted on trains to provide alternating current from direct current. Popular nowadays for DC railways to allow three phase drive or for auxiliary supplies which need an AC supply. Line Breaker Electro-mechanical switch in a traction motor power circuit used to active or disable the circuit the circuit. It is nomally closed to start the train and remains closed all the time power is required. It is opened by a command from the driving controller,no-volts detected, overload detected and (were required) wheel spin or slide detected. It is linked to the overload and no-volt control circuits so that it actually functions as a protective circuit breaker. Master Controller Driver’s power control device located in the cab. The driver moves the handle of the master controller to apply or reduce power to the locomotive or train. Motor Blowers Traction motors on electric locomotives get very hot and to keep their temperature at a reasonable level for long periods of hard word, they are usually fitted with electric fans called motor blowers. On a modern locomotive,they are powered by an auxiliary 3-phase AC supply of around 400 volts supplied by an auxiliary inverter. Rectifer A converter consisting of thyristors and diodes which is used to convert AC to DC. A modern locomotive will usually have at least two, one for the power circuits and one or more for the auxiliary circuits. Synchronous Motor Traction motor where the field coils are mounted on the drive shaft and the armature coils in the housing, the inverse of normal practice.Favoured by the French and used on the high speed TGV Atlantique trains, this is a single-phase machine controlled by simple inverter. Now superseded by the asynchronous motor. Transformer A set of windings with a magnetic core used to step down or step up a voltage from one level to another.The voltage differences are determined by the proportion of windings in the input side compared with the proportion on the output side. An essential requirement for locomotives and trains using AC power, where the line voltage has to be stepped down before use on the train. Equipment Layout Ventilation System Equipment layout and ventilation systems 設備布置和通風系統設計 Equipment layout and design of the ventilation system 電力機車簡介 機車是為列車提供驅動力，而自身并沒有效裝載能力的車輛；他的唯一目標是沿著軌道牽引列車。通常自帶動力的車輛不被視為機車，在客運方面自帶動力的車輛用得越來越普遍，但是很少用在貨運。自帶驅動力的車輛以驅動列車的車輛，通常它們不視為機車，因?yàn)樗鼈兙哂杏行аb載能力，并且很少從列車上摘掛，它們稱之為動車。 一般來說，機車牽引列車?，F(xiàn)今在客運業務上拖拉式運營方式越來越常見，采用這種運營方式的特點是：機車在一端牽引列車，然而卻由在另一端的司機室控制。 機車的優點： 在一般情況下,為什么將為列車提供驅動力的機車和車輛是分開的，而不是車輛自帶動力的原因包括以下幾點： 1． 易于維修—維修一臺機車和維修自帶動力的車輛相比要容易。 2． 安全—通常將列車牽引動力裝置安裝在遠離乘客的地方比較安全，這一點對于蒸汽機車來說顯得相當重要，但是有時會仍然會出現一些不如意的情況。 3． 易于更換動力—如果動力裝置損壞，用一個新的來更換它即可，這樣地來顯得比較容易，從而一個動力裝置產生故障時不至于整臺機車無法工作。 4． 效率—當列車空載運行時可以將機車從列車上摘卸下來。機車再去執行其它牽引業務，這意味著不但可以降低列車運營成本，還可以提高機車的使用效率。 5.將機車和車輛分離開來意味著當機車出現故障時，只需更換機車就可以這樣就可以不影響列車的運營。在有些情況下車輛比機車先報廢，如果機車和車輛不可摘掛，那么即使機車完好也得跟著報廢，這樣就意味著浪費和成本高，然而機車可以從列車上摘下來，只需更換車輛即可，這樣五來大大的降低了成本提高了經濟效益。 電力機車 電力機車是通過接觸網或第三軌由外部提供電能。盡管電氣化鐵道的造價相當高，然而運營成本卻比內燃機車低，良好的加速性能和可再生制動，使得它們在繁忙干線地區成為客運業務的理想選擇。幾乎所有的高速鐵路都采用電力牽引（例如ICE，TGV），由于具有如此高的性能，機車所需要的電能是不容易得到提供。例如應用在海底隧道貨運業務的現今最大功率的機車的功率高達7MW。 第一臺電力機車由Scotsman和Robert Davidson于1837年設計并生產，該電力機車由電流單元提供動力。 現代電力機車包括從由蓄電池提供能量的用于礦山的機車到功率高達6000馬力(4.5M)甚至功率更高的干線電力機車。 事實上，現代許多機車它們是電力驅動的，純電力機車是從外部獲得電能，然而內燃電力機車它們卻自帶發電裝置。 干線電力機車第一次出現在20世紀初，電力機車的誕生是由于蒸汽機車產生在運行過程產生的煙霧給駕乘帶來不便和不安全，特別是在隧道。在英國引入電力機車的是由于地鐵系統的需要。然而在美國引入電力機車卻是由于河底隧道這樣一個特殊的工作環境下采用內燃牽引無法滿足要求。 早期電力機車全都依靠外部提供電能，盡管它們運行可靠和效率高，但是建造接觸網是一筆相當大的投資，并且需要不斷維護?；诖?，電氣化鐵道僅僅在繁忙干線采用。在市郊采用電氣化鐵道可以減輕由蒸汽機車燃燒所帶來的粉塵污染。 世界列車最高運行速度紀錄由法國TGV在1990年創立。速度高達515.3千米每小時(320mph)。 然而，近來所設計的電氣化鐵道幾乎都采用交流制，當然許多已有的直流供電制仍然在用，例如：南非，西班牙，英國（750V和1500V），挪威（1500V），安哥拉，意大利，波蘭（3000V），芝加哥和Mumbai（它們將由2025轉換成交流供電制）。 早期的機車有各種型式。通常它們設計成與供電制相匹配的機車。于是采用直流供電制的電氣化鐵道的鐵路系統，電力機車的牽引電機為直流電機。采用交流供電制的電氣化鐵道的鐵路系統，電力機車的牽引電機為交流電機。交流可以是單相，也可以是三相，單相需要兩根導線，一根是接觸網，另一根是鋼軌。三相需要三根導線，因此三相電力機車有兩根接觸網，鋼軌作為第三根。 直流供電可以用接觸網或鋼軌供電，通常稱之為第三軌。 交流牽引電機體積比直流牽引電機的體積小。通常這就意味著直流電機可以做得體積小些。安裝驅動軸，通常采用齒輪傳動。但是在早期也有采用軸的。即便如此，一些著名的直流電力機車采用直流電動機驅動車輪。 采用電力機車作為牽引動力的一種可能就是在制動期間電動機可作為發電機并把發出的電能反饋給接觸網，這種被稱之為再生抽動。這是一個新的想法，這就是三相交流供電制為什么要采用的原因。特別是在山區，機車下坡時產生的能量以供機車使用。瑞士鐵路采用這種系統。三個下程供給一個上程。 現今，所有電力機車都趨于將驅動電機安裝在靠近車輪軸的位置，盡管仍有些電力機車將驅動電機安裝在車體內通過傳動裝置來驅動車輪。 現代實體狀態電控系統的采用意味著電機并不需要和供電制相匹配。因而在今天，多電壓等級的機車已相當普遍。通常驅動電機是直流電機，但是在一些機車上也有三相驅動電機。 蓄電池機車在礦場和由內燃機產生的煙是一個不安全隱患的其它地下作業和外部電能不可獲得的情況下利用。蓄電池機車在許多地鐵系統當供電被暫時切斷而需要維修作為維修作業車。 電力機車的各組成部分: 異步電動機 現代牽引電機主要采用三相牽引電機,并被廣泛應用于現代列車牽引系統.采用適當?shù)目刂齐娮友b置后,三相牽引電機可以用在直流或交流制的電氣化鐵道和內燃機車. 電池 所有的列車都備有電池以提供起動電流和為一些裝置提供電源,例如當接觸網供電失敗時的緊急照明,通過電池是和直流控制供電裝置相連. 斷路器 電力機車通常備有一定型式的空氣斷路器以將從接觸網隔離,當機車發生故障,或者需要維修時。在交流制供電式中，斷路器通常安裝在機車頂部靠近受電弓的一側。現有兩種類型的斷路器：空氣斷路器和真空斷路器（VCB）。空氣或真空是用來滅當斷路器的兩連接端分開時產生的電弧。真空斷路在英國用得比較多，而空氣斷路器在歐洲大陸用得比較廣泛。 逆變器 將交流轉變成直流稱之為整流，將直流轉變成交流稱之為逆變。逆變這一詞起源于美國，但是現在這一學術用語在其它地方也被用。 冷卻風扇 為了冷卻整流裝置和其它電子裝置，現代機車都裝有空氣管理系統，電子控制裝置使所有的系統都運行在允許的溫度范圍內。風扇由一臺產生400伏電源的三相交流的輔助逆變裝置供電。 直流連接器 在三相和單相整流器中，直流連接器用在現代電子電源系統中。通過將交流電整流成直流，然后將直流逆變成三相交流，很容易將從接觸網獲得的單相交流電轉變成所需要的三相交流電。 線路斷路器 在列車上安裝電力電子器件可將直流電轉換為交流電。當今采用直流供電制的鐵路系統也廣泛采用三相牽引電機和一些輔助設備也采用三相交流電。 電子機械開關 安裝在牽引電機上電子機械式開關以斷開和接通牽引電機電路，通常情況下開關是閉合的。它受牽引控制器的指令控制，而并非電壓檢測傳感器的控制。它和過載檢測裝置和非電壓控制電路相連接以便在發生過載時切斷電機電路以保護牽引電機。 司機控制器 驅動力控制裝置安裝在司機室。司機移動司機操縱手柄以提高或減小機車牽引力。 牽引電機冷卻風機 電力機車上的牽引電機很容易發熱，牽引電機在長時間滿負荷運行式?jīng)r下，為了使其溫升在允許的范圍內，通常給牽引電機安裝有風扇稱之為冷卻風機。在現代機車上，風扇由一臺產生400伏左右電源的三相交流輔助逆變裝置供電。 整流器 整流器由將交流轉換為直流的可控硅和二極管組成。通?，F(xiàn)代電力機車至少有兩個整流器，一個用于主電路的整流，一個用于輔助電路的整流。 同步電動機 牽引同步電機是 勵磁線圈安裝在驅動軸上 電樞線圈安裝在定子上的電機, 這和通常的電機剛好相反。這種電機在廣泛應用在法國用于高速列車用得由法國和它采用了高速的TGV大西洋列車 這是一種由簡單逆變器控制的單相電機?，F(xiàn)在已被異步電動機取代了 。 變壓器 變壓器是由鐵芯和繞組組成且將電壓由一個等級升高或降低到另一個等級的設備。變壓器的輸出電壓由輸入側和輸出側繞組匝數之比決定。變壓器作為電力機車不可缺少的設備其將從接觸網的電壓變換成機車在牽引工況下所需電壓。