定柱式懸臂起重機結構設計與分析,定柱式,懸臂,起重機,結構設計,分析 ****學院****屆畢業設計說明書 定柱式懸臂起重機結構設計與分析 摘要： 定柱式懸臂起重機是由立柱、回轉臂、懸臂驅動裝置和電動葫蘆組成。立柱下端底座通過地腳螺栓固定在混凝土基礎上，由電機帶動減速機驅動裝置使懸臂回轉，電動葫蘆在懸臂工字鋼上作往返運行作業。它的特點有：自重輕，懸臂長，起重量大，安裝、操作、維修簡單。它們完全獨立，是一種理想的工作崗位起重機，并適用于室外的貨場和裝卸平臺。定柱占地面積小。對于起升凈空非常小的情況下也能獲得最大的起升高度。 本設計從整體設計出發，依次設計計算了2t定柱式懸臂起重機的懸臂和立柱的主要機構部件。選取了螺栓，開式齒輪等主要零部件。設計了符合要求的懸臂結構，并校核了軸承，焊縫強度和轉動軸鍵的強度和剛度等力學性能參數。在設計過程中，運用優化設計的方法，使各個結構盡量達到最合理的布置和選擇。 關鍵詞:定柱式懸臂起重機金屬結構 column?cantilever?crane’s?structure design and analysis Abstract: Slewing cantilever crane is a column, rotating arm, cantilever drive and the composition of electric hoist. Column bottom of the base fixed to the concrete foundation by anchor bolts on the gear driven by the motor drives the cantilever rotary, electric hoist for the cantilever-beam on the run from job . Its characteristics are: light weight, arm length, lifting capacity, installation, operation and maintenance simple. They are completely independent, is an ideal job cranes, and applies to the outdoor yard and loading platforms. Set column small footprint. For lifting the case of very small clearance can get the Maximum lifting height. At the beginning of this design of main mechanism of 0.8t in the column cantilever crane cantilever and the column component calculation.The main parts such as bolts, open gear. Designed to meet the requirements of the cantilever structure, and check the bearing, weld strength and the rotating shaft to bond strength and stiffness and other mechanical properties. In the design process, using the method of optimal design, the structure to achieve the most reasonable layout and selection. Key words: Slewing cantilever crane Metal structure ****學院****屆畢業設計中英文翻譯 Crane Work Needs More Technique The invention of crane has greatly increased people’s work efficiency .People can use crane to handle with huge articles which used to be taken a long time to do, especially in a small are The bridge type hoist crane is required to handle with huge accessory? or?huge device. The birth worldwide industry early post-war years, the crane industry came to an aImost complete standstill. By the end of the decade, however, crane construction had diversified and spread around the world and the industry seemed infused with newfound energy that left it flourishing as never before. Lightweight cranes that arrived on site ready for use came to dominate construction sites as people realised the advantages of not having to dismantle them between jobs. These new designs did away with the need to have other lifting equipment assisting during rigging - a big contrast to the cumbersome rigging of previous designs. But, before all this could happen came the horrors of the Second World War. By 1940 of Europe was completely caught up in the conflict. By the time the war ended, Europe and other parts of the world had been subjected to extraordinary political, economic and social changes that would affect the entire fabric of society, including the construction and crane industries, for many decades to come. In the US, steam locomotives were starting to be replaced by diesel - by 1953 more than 50 per cent of all locomotives would be diesel. During the war the mass production of excavators, scrapers and cranes continued. 1940, for example, saw Thew launch the new 'Lorain Motocrane' series. This consisted of three cranes which, for the first time in history, were mounted on chassis built by the crane manufacturer itselfi The smallest crane, the MC-2, could lift 7.6 tonnes, the MC-2 9.9 tonnes and the MC-3 13.5 tonnes. These cranes were delivered to the army by the thousand, and were also mounted on portals for use as harbour cranes (the MC-4 model). The war had, of course, taken its toll on the number of able-bodied men available to work in the crane industry and there was a serious shortage of good crane drivers. At Thew, newcomers were taught crane operations over a two-day course presented by A.C Burch, an experienced mechanic and graduate of the Naval Academy, and L.K Jenkins. These two gentlemen were probably the originators of 'operator training' as we know it today. As they had actually designed the Motocrane, both knew it inside out and were pleased to pass on this knowledge. When the Japanese National Railways committed itself to buying the prototype of a machine designed to remove railway clips, the tide turned. The machine worked splendidly and iVlasuo Tadano toured Japan showing on 35 millimetre film just what it could do. He collected numerous orders for the machine along the way and at the same time seems to have been an early pioneer of the company videos so beloved by today's marketing professionals! Other countries were also building noteworthy cranes. Italy, in particular, was developing into a source of innovative ideas for the industry.In1948 in Legnano,near Milan,Carlo Raimodi built his first slewing tower crane,a classic top slewer The company was originally established in 1863 as a foundry and had, until making its crane debut, built machines and components for the millwright and other industries. There was now a worldwide boom in construction and this attracted the attention of specialist equipment manufacturers, many of whom followed the launch of crane ranges with the introduction of concrete mixing equipment. This combination of equipment was supplied in a variety of forms: Reich, Ibag and Liebherr, for example, supplied cranes and concrete mixing machines designed to be used together. Important slewing tower crane manufacturer. The bridge type hoist crane car consists of protmoted organization，the car frame，the car movement organization，hoisting mechanisms and so on. Its operation structure is composed of reducer，the driving wheel group，the driven wheel group，the transmission shaft and some connect fitting. The core of this structure is the design of the reducer. This bridge type hoist crane is be used to the hydroelectric power station. It is installed in the expanded workshop of Fengman water and electricity station.It is used to installing,examining and repairing the water-turbine generator set and its accessorial equipments.the equipments in the water and electricity station are large?or?medium-size. These equipments have a high request on the load of bridge type hoist crane , so they also have a high request on the capability of the reducer. Grab bridge bridge crane is running on the elevated track, the car driven by the lifting of materials crawl grab a bridge-crane. Bridge laying on both sides along the elevated track on the vertical run, lifting trolley along the bridge in laying the track on the horizontal run, a rectangular scope of work, you can make full use of space below the bridge lifting material from Ground equipment hindered. Grab bridge cranes widely used in power plants, Mei Chang, and other needs of bulk material handling of the occasion, because of the heavy equipment, transportation difficulties installation, testing the quality of their products in general need in the field. Therefore, control equipment requirements for wiring, small size and portability. And the use of fixed-site conditions, also called a random testing equipment manual control functions to ensure the safety of operation. With the lifting of the transport requirements of the mechanical control continuously improve, more and more advanced means of control. At present the domestic bridge crane control system requires people at the scene to control, control methods are backward. In small and medium-sized crane, the most direct control over the use of controllers, car running, Lord, vice hook upgrade, dropped weights and speed Crane work needs more technology. Construction of tower cranes are the main vertical transportation equipment and also a measure of construction companies and equipment strength of the important logo, in today's increasingly competitive construction market, to meet the construction needs of many construction companies have bought the tower crane. With the tower crane at the construction site of the widely used by the tower crane accident also caused more and more to people's lives and property brought about great losses. According to national statistics, the departments concerned, the tower crane accident rate reached 2.77 percent. Its security problem is still the urgency of the construction Loose training, testing and oversight requirements for the people who work around construction cranes have fostered a false sense of security in our industry. The recent deadly tower-crane collapse at a congested New York City building site should be a wake-up call for us to question and step up our current safety practices. Training and testing is king when it comes to safety. But the construction industry is putting unqualified personnel in the seats of construction cranes, even with today's testing. In many places, no experience is necessary after passing a standardized test. One week of study will give some people enough knowledge to pass a certification examination, and then they can jump into the cab of a crane. Imagine that a commercial airline pilot had the same training as a certified crane operator. How would you feel the next time you decided to fly? In California, it takes more hours of training to wield a pair of scissors in a hair salon than to operate potentially dangerous lifting machinery. How does this make sense? Riggers and signal persons also need standard training and testing to ensure safety under the hook. Employers usually allow any craft to signal a crane on a jobsite, despite best practices that require only qualified people do so. How is it then that uncertified and untrained people are allowed to signal and rig under the hook of a licensed or certified operator? Tower cranes are particularly risky as urban sites become more congested, and the risk of a catastrophic event is very high during climbing operations. Yet most tower-crane climbing crews are trained in a non-traditional manner, via secondhand knowledge that has been passed down over time. The problem with this type of hand-me-down knowledge is that it changes over the years, leaving out small-but-important details along the way. This "osmosis" of knowledge leads crews to develop their own tricks for climbing cranes, often forsaking basic safety in an attempt to save time and energy. In many cases, there are no safety devices or alarms to warn of a serious problem. Climbing crews are subjected to pressures that affect safety-critical decision-making. It is not uncommon for climbs to continue with damaged or leaking hydraulic systems, out-of-adjustment or jammed guide rollers, often working in the dark and for extended hours. This "MacGyver" method of climbing, where every jump becomes a new adventure, should not be the norm. Climbing-frame designs vary among manufacturers, but the operational steps are similar in principle. The climbing process is relatively straightforward, with a mixture of physical work and technical procedure. It is not complex; it is more about knowing the proper sequence of what needs to be done and then following the steps, one by one, making sure each step has been successfully completed before moving onto the next. It is essential that everyone know exactly what is going on and what the dangers are at every stage. When these needs are satisfied, crane operations should be carried out in strict accordance with the manufacturers' instructions, engineering principals and governmental laws. But industry stakeholders and lawmakers need to step up their lax standards to protect the public. New York City residents, who have seen their homes turned into dust and debris, would be shocked at the way the industry deals with these issues. That's why the industry needs standardized training, testing and oversight for this work, including a practical assessment of competence. Technicians should have model-specific training directly from the manufacturer, along with a level of practical experience. Inspectors, too, should be required to have specific technical training. They should be independent from all aspects of installation and maintenance to allow for objective decisions. Key personnel on erection crews should have standard training and testing. 第 9頁 第 9頁 起重機工作需要很多科技 起重機的出現大大提高了人們的勞動效率，以前需要許多人花長時間才能搬動的大型物件現在用起重機就能輕易達到效果，尤其是在小范圍的搬動過程中起重機的作用是相當明顯的。 戰后的前幾年，世界性的工業誕生了，起重機行業幾乎完全停止。然而到這個年代末，起重機的建造變得多元化并傳播到世界各地，它的前所未有的蓬勃發展似乎整個工業注入了新能源。輕型起重機投入到工作地點并準備作為主要機械，因?yàn)槿藗円庾R(shí)到了在工作間不用拆除他們的的優點。這些新的設計也不再需要其他起重設備協助操縱——相比以前在安裝前要進行繁瑣的設計。但是，在這一切之前發生了恐怖的第二次世界大戰。到1940年，歐洲完全陷入了戰爭中。到戰爭結束后的幾十年來，歐洲和世界其他地區發生了巨大的政治，經濟和社會變化，將影響整個社會結構，包括建造業和起重機行業。在美國，蒸汽機已開始改為柴油機——到1953年超過百分之五十的機車將使用柴油機。戰爭期間，挖掘機，鏟運機和起重機的大規模生產在繼續。例如1940年，看到Thew推出新的'Lorain Motocrane'系列。這其中包括三種起重機，是歷史上首次自身安裝了底盤的起重機。最小的MC - 2 ，起重量達7.6噸， MC – 2起重量為9.9噸，MC – 3起重量為13.5噸。這些起重機許多被用于軍隊，有的還安裝在港口用作港灣式起重機（在MC - 4型） 。當然，這場戰爭已經削弱了能在起重機行業工作的健壯的男人的數量，并且優秀的起重機司機嚴重短缺。在Thew ，一位畢業于美國海軍學院的經驗豐富的技工A C Burch和L K Jenkins進行了為期兩天的起重機業務課程的教授。這兩位紳士好比是我們今天所知的“經營者培訓”的創始人。他們實際上已設計了動力起重機，都深深地了解起重機，并很高興傳授這方面的知識。 當日本國家鐵路公司致力于采購一種旨在搬動鋼軌扣板的原型機，潮流逆轉。該設備工作極為出色。iVlasuo Tadano環游日本，用35毫米的電影展示該設備的強大用途。沿路上，他獲取了大量訂單。同時，他好像成為當今市場營銷專家所寵愛的公司影像傳播的先驅！ 其他國家也在大力發展起重機。特別是意大利，逐漸發展成為該行業的創新基地。1948年Carlo Raimodi在米蘭附近的Legnano，首次建造了回轉塔式起重機，一種經典的頂端回轉起重機。公司最初成立于1863年，在生產起重機之前，是一間鑄造廠并為技工和其他行業生產機械設備。當時全球建筑業空前繁榮，吸引了專業設備制造商的注意。其中許多公司在推廣起重機后，推出了混凝土攪拌設備。提供了多種不同組合，例如，Reich，Ibag和Liebherr設計開發了起重機與混凝土攪拌設備一起使用的組合。 橋式起重機小車運行機構設計主要包括起升機構、小車架、小車運行機構、吊具等部分。其中的小車運行機構主要由減速器、主動輪組、從動輪組、傳動軸和一些連接件組成。橋式起重機是水電站橋式起重機，安裝于豐滿水電站擴建工程廠房?jī)?nèi)，用于水輪發電機組及其附屬設備的安裝和檢修工作。水電站內設備一般都是大中型設備，對橋式起重機的載荷要求較高，所以對減速器性能要求較高。 橋式抓斗起重機是橋架在高架軌道上運行，由起重小車帶動抓斗抓取物料的一種橋架型起重機。橋架沿鋪設在兩側高架上的軌道縱向運行，起重小車沿鋪設在橋架上的軌道橫向運行，構成矩形的工作范圍，就可以充分利用橋架下面的空間吊運物料，不受地面設備的阻礙。橋式抓斗起重機廣泛應用于電廠、煤廠等需要散料裝卸的場合，由于該設備笨重，運輸安裝困難，對其產品質量檢測一般需要在現場進行。所以要求控制設備接線方便，體積小便于攜帶。又由于使用現場條件不動，還要求檢測設備有隨機手動控制功能，以保證運行時的安全。隨著對起重運輸機械控制要求的不斷提高,控制手段也越來越先進。目前國內的橋式起重機控制系統都需要人在現場進行控制，控制方式都比較落后。在中小型起重機中, 大都采用控制器直接控制大、小車運行, 主、副鉤提升、下降重物及調速。 塔式起重機是建筑施工垂直運輸?shù)闹饕O(shè)備，也是衡量一個建筑施工企業裝備實力的重要標識，在當今競爭日益激烈的建筑市場，為滿足施工需要，很多施工企業都購置了塔式起重機。隨著塔式起重機在施工現場的廣泛使用，由塔式起重機引發的傷亡事故也越來越多，給人民的生命財產帶來重大損失。據國內有關部門統計資料表明，塔式起重機的事故率已達2.77%。其安全問題仍然是建筑施工中的憂患。 松散的培訓，測試和監督的要求, 周圍的建筑起重機給這些工作的人樹立了一種虛假的安全感，在我們的行業。最近塔式起重機倒塌在一個繁忙的紐約市建筑地盤應敲響警鐘，提醒我們問題的存在，并加強我們目前安全的做法。 當談到安全問題時，訓練和測試是關鍵。不過，建造業是把不合格人員放在建筑起重機的駕駛位上，甚至沒有通過今天的測試。在許多地方，沒有任何經驗必須合格的通過標準化的測試。一周的學習將給予一些人足夠的知識足以通過認證考試，然后他們可以跳轉到的起重機的駕駛室。 想象一下一個商業航空公司飛行員和一個認證的起重機操作員有相同的訓練。你會如何感覺，下一次你決定要坐飛機？在加利福尼亞州，掌握一對剪刀在頭發沙龍比操作有潛在危險的起重機械需要更多的時間訓練。如何，這是否合理？ 裝配工人和發信號的人也需要標準的培訓和測試，以確保安全下鉤。雇主通常允許任何工人發信號指揮起重機上工地 ，盡管最佳做法是需要合格的人這樣做。怎么能允許那么無證和未受過訓練的人來代替有工作證或經核證的操作者呢？ 塔式起重機是特別危險的，尤其是在市區用地變得更加擁擠時。攀登行動更是一個風險的行動，其災難性非常高。然而，大多數塔式起重機攀登員的訓練，在一個非傳統的方式，通過二手知識已流傳一段時間。問題與這種類型的現成的知識是，多年來，留下來的非常少，但最重要的細節卻丟失了。這種“滲透”的知識，導致操作者只能發展自己的技巧攀登起重機，往往放棄基本的安全，企圖以節省時間和能源. 在許多情況下沒有安全裝置或警報來提醒嚴重的問題的存在。攀登人員容易遭受到影響安全性至關重要的決策所帶來的壓力。攀登時，使用損壞或泄漏的液壓系統，沒有任何的調整，這并不鮮見。在黑暗中工作和延長工作時間是時有發生的。這種攀登方法，其中的每一次攀登都會成為新的冒險，不應該作為規范被采納。 攀爬架的設計，在制造商之間存在不同，但設計的步驟在原則上是相似的。攀登過程中是相對比較明了的，配合著的體力勞動和技術程序。這是并不復雜，它是更多地了解知道正確的序列需要做什么，然后按照下列步驟，一個又一個，確保每一步在做下一步前成功完成。這是十分重要，每個人都清楚的知道事情進展的怎么樣，在每一個階段存在什么樣的危險。 當這些需要得到滿足，起重機作業應進行嚴格按照有關制造商的指示，工程原則和政府的法律。但業內人士和國會議員，要加強他們的寬松標準，以保障公眾利益?？吹阶约旱募覉@變成了塵埃和碎片的紐約市居民，會對處理這些問題的方式感到震驚。 這就是為什么業界需要規范的培訓，測試和監督，其中包括一個實際的評估能力。技術人員應該隨著實際經驗的提升，直接從制造商哪里獲得標準訓練。視察員同樣也也須有具體的技術培訓。他們應獨立于安裝和維修的各方面，這由客觀決定。架設的關鍵人員應該有標準的訓練和測試.