電風扇葉片鎖緊螺母的注射模設計【一模兩腔】【側抽芯】【說明書+CAD+PROE】,一模兩腔,側抽芯,說明書+CAD+PROE,電風扇,葉片,螺母,注射,設計,說明書,仿單,cad,proe 南京理工大學泰州科技學院 畢業設計(論文)外文資料翻譯 系　　部： 機械工程系 專 業： 機械工程及自動化 姓 名： 周峰 學 號： 05010154 (用外文寫) 外文出處：WORCESTER POLYTECHNIC INSTITUTE 附 件： 1.外文資料翻譯譯文；2.外文原文。 指導教師評語： 譯文比較正確地表達了原文的意義、概念描述基本符合漢語的習慣，語句較通暢，層次較清晰。翻譯質量良。 簽名： 年 月 日 注：請將該封面與附件裝訂成冊。 附件1：外文資料翻譯譯文 熱等靜壓合并過程的發展和 解決鋁鑄件浸滲的熱處理過程的成本效益 由于A356（7％硅，鎂0.4％）鋁合金鑄件的形狀復雜性和良好的強度重量比，在汽車行業越來越多的使用這些部件。然而，這些零件的應用受到鑄造條件的限制，被應用于一些機械性能較差的行業。這些較差的機械性能源于合金鑄態條件的兩個基本問題。第一個問題是這些鑄造合金凝固的不均勻。這種不均勻的原因是內冷卻模具的不一致導致合金基體不均衡分散粗糙形成沉淀。這又導致在鑄態條件下產生較差的拉伸性能。第二個問題是鑄態組織中所固有的孔隙度。這孔隙度分為兩個不同的種類，縮孔和氣孔的孔隙度?？紫堵适且簯B(tài)金屬體積大于固態金屬體積收縮所造成的。氣孔是高溶解度的液氫和鋁熔體中的氫因為溫度降低蒸發所造成。孔隙度會影響鑄造的延展性，斷裂韌性和疲勞性能。幸運的是，在鑄造行業，這些問題的內在鑄條件可緩解鑄造加工。解決熱處理的其次是精煉過程，完善微觀結構和改進合金的機械和物理性能。浸滲可以消除鑄造中的孔隙。對鋁合金鑄件開始加熱溶解合金基體的熱處理，稱為固溶處理，或固溶。 擴散退火采用高溫熱處理溶解第二階段的沉淀物，是使初級階段改變共晶硅相的形態均勻牢固的解決辦法。如A356 ，析出的Mg2Si 。為了防止Mg2Si顆粒再次沉淀，采用快速淬火的解決方案。淬火的鑄件還能保證維持固溶步驟和結果的均勻化。為了達到最大強度的沉淀硬化或時效熱處理。人工時效發生在稍高溫， 165 ℃ ，而自然時效發生在室溫。均一實現前面的步驟確保分散的顆粒統一成型在時效階段。人工時效，以達到最大強度認為的鑄造韌度為T6 ，而自然時效使鑄件的韌度指定T4。熱等靜壓，簡稱HIP，通常是完成熱處理之前一種消除鑄件孔隙的方法。熱等靜壓是對鑄件加壓氣體，這適用于靜力表面的鑄造,升高溫度，以推動物質流動。占主導地位的精密機器鑄造過程中是初始階段的熱等靜壓過程塑性流動。由于鑄件長時間在高溫和壓力下,使機械裝置的機制產生變化，首先是蠕變，然后擴散蠕變機制（Nabarro-Herring，科布爾蠕變）?？偟男Ч恰昂附印钡墓铝⒖紫秲鹊蔫T造[Atkinson]。由于時間密集性質的熱等靜壓過程中，一些變異的原始過程已經制定，最大限度地返回熱等靜壓過程，同時盡量減少過程的時間和成本，是生產鋁鑄件的關鍵。液體熱等靜壓（LHIP）使用不可加熱的液體加壓媒體[Chandley]。指導原則在制造過程后指出，靜壓工藝大多數用于加壓和減壓空氣等可壓縮氣體。在熱等靜壓過程中，鑄件浸在鹽水和整個鹽水壓力容器通過液體沖壓非?？?。通過這種方法，最快的只要幾秒，而不是那個需要幾個小時的熱等靜壓的過程。此外，這過程可被整合成一個連續鑄造過程[Chandley] 。然而，最大壓力鑄造的A356在熱等靜壓過程持續約只有三十一秒[Romano et al.] ，它不允許任何前面所提到的蠕變機制發生。瑞達公司已采取另一種辦法來降低熱等靜壓工藝鋁鑄件的成本。該Densal過程是一個專有的熱等靜壓進過程，專門定制的熱等靜壓工藝技術規格和硬件專門為鋁鑄件。溫度和壓力擴散蠕變機制隨時間在變化。據估計，Densal過程降低的熱等靜壓鋁鑄件成本多達70%[ Mashl等] 。不過，進一步提高Densal過程經濟性是有可能的。由于相似過程的溫度解決[Mashl et al.]方案熱處理和Densal 過程中，結合這兩個過程甚至可能會產生進一步削減熱等靜壓及熱處理鋁鑄件的成本。這樣做的原因是制定和評估的可行性，這種合并 Densal+固溶過程。 將其中包括這兩個大部分已完成的工作文件提出發表。每個文件是一個獨立的工作，摘要，引進，程序，結果和討論，結論和參考節。第一份文件列為第2章介紹了實驗結果相結合的過程Densal和解決熱處理對一些鋁硅鎂商業鑄件。第二份文件，第3章，介紹了成果的理論能源計算相結合過程中的個別過程Densal其次是以后的熱處理。 應用鋁鑄件的汽車行業合并熱等靜壓（HIP）/解決熱處理過程關鍵是盡量減少生產成本和熱處理時間。一個完整合并過程是在相同的時間和物力下，使生產部分單獨的生產過程和熱等靜壓后的熱處理提高效率。在這項研究中，有一個實驗組合工藝設計和實施生產設施。工業生產鋁鑄件合并的過程，是通過拉伸和疲勞試驗和顯微鏡檢查并量化的結果。樣品在比較疲勞和拉伸強度進行了傳統熱等靜壓和熱處理，以及樣品在非靜壓T6條件下。結果表明：根據鑄件的疲勞性能適合獨立的熱等靜壓和熱處理工藝合并過程批量生產。此外，與組合工藝相比，只要鑄件制作時進行熱處理，就能改善疲勞壽命的一個數量級。這一研究表明比較任何拉伸性能所造成的加工路線無明顯差異的。此外，微觀的比較鑄件孔隙率的加工路線以外的加工無顯著差異，這只是非熱等靜壓樣品。樹枝狀孔隙度和樹枝狀結構的樣本，解決方案同一時間是相同的。實驗相結合的方法也顯示這些的生產試驗可以節省大量的時間。 鋁鑄造是一個廉價的生產方法，零件形狀復雜性，優良的強度重量比和良好的耐腐蝕性。由于這些原因在汽車行業鋁鑄件的使用率正在上升。但是，大多數的鋁合金鑄態條件下許多應用上不顯示所必需的的力學性能，因此需要隨后的熱處理，以優化合金的結構[ 1 ]。此外，隨著越來越多地強調鋁鑄件的周期性應用，如汽車懸架系統，最大限度地提高部件疲勞壽命的熱處理變得越來越重要。浸滲或消除鑄件內在的孔隙度，對零件的疲勞抗性十分重要，鑄造毛孔往往是疲勞限制的原因。 [ 2-6 ] 。迄今為止，微觀結構雖然通過熱處理和疲勞兩個獨立的處理方法性能的優化致密得到完善。在大多數情況下硅鋁合金，熱處理表現出來的往往固溶的一步過長，緊隨其后的快速淬火和隨后控制成型時間[ 1,7 ]。根據國際ASM，大多數硅鋁合金在T6條件下熱處理可以提快18 小時實現[ 1 ]。共晶硅新技術的改進可以大大降低解決熱處理時間，但浸滲的步驟仍需要以改善鑄件的疲勞性能[ 9 ]。為此，熱等靜壓（HIP）前進行熱處理工藝已被證明是一種有效的手段，增加疲勞壽命的重要應用部分。 通過消除收縮鑄造中的氣孔。與同一個非熱等靜壓樣本相比，可見熱等靜壓部件疲勞壽命多增加了一個數量級[ 2-6 ]。HIP過程包括鑄件與加壓氣體給予靜水壓力元件[ 10,11 ]。同時高溫高壓，使氣孔收縮或消除。初步浸滲在鑄造時通過獨立的塑性流動開始。然后，控制高溫和壓力的時間，通過擴散發生蠕變機制完成浸滲[ 10,11 ] 。該鏡以下顯示的影響等靜壓致密。毛孔，標有箭頭，非熱等靜壓樣品（圖1 ）被熱等靜壓樣本（圖2 ）排除。 圖1. 鑄造鋁硅鎂合金在T6條件;箭頭顯示孔隙 圖2. 鑄造鋁硅鎂合金在熱等靜壓 T6條件;沒有跡象表明孔隙度 目前，熱等靜壓是一個獨立的處理方法，它會增加鑄件制造成本。為了盡量減少這種鋁鑄件成本，瑞達公司已開發出一種專利過程稱為Densal。Densal 優化了熱等靜壓過程和鋁鑄件專門硬件，代表著降低這一過程成本的進步[6]。 在當前生產鑄件過程中最具成本效益的的是Densal方法的應用，其次是T6熱治療[6] ，雖然Densal是一個增值過程，但仍然使用它控制時間和能量。 由于熱等靜壓周期和固溶吸收部分熱處理周期的峰值溫度相似，進一步整合兩個過程可以節省大量的時間和能量。這一組合的提議本來就有困難。首先，由于高壓所固有的熱等靜壓的過程，快速淬火的熱等靜壓目前不可行。其次，即使晶體合金改進，通常是熱等靜壓容器溫度保持時間不夠長來完整固溶。本研究是調查的可行性相結合的商業 Densal /解決熱處理的過程。為此，將制定和實施一項實驗相結合的過程。其次，將進行調查影響工業鑄件合并過程的微觀結構和拉伸強度和疲勞性能。試驗結合熱等靜壓/解決熱處理的可行性的制造程序已經開發出來。這一方法是改進當前熱等靜壓部分，完全解決熱處理的熱等靜壓容器使其能夠滿足從固溶溫度。鑄造過程中的合并過程經過相同的獨立解決熱處理將影響鑄件表面溫度。 具體來說，鑄件的溫度將提高到溶化溫度，持續一段時間，然后通過傳統的水淬使溫度迅速下降。同時進行的固溶浸滲。在同一時間提高鑄件的溫度，圍繞鑄件的氣體壓力也將上升到一定數值。這壓力保持的時間為標準Densal保壓時間，而不是對整個固溶時間。當解決方案的溫度保持和剩余的固溶時間完成時，壓力將減少。其中有一個重要問題需要加以解決，以確定采用熱等靜壓爐的可行性合并方法是否有足夠力量去克服該容器絕熱冷卻時壓力過大而可能產生的泄露?？紤]到傳熱之間的鑄件和加壓氣體, 這個問題變得日趨重要。運行壓力容器等靜壓加壓氣體和鑄件的傳熱比率大約是100W/m2k[ 12 ]。但是，如果能夠保持爐的鑄造固溶溫度，Tsolution,而容器內的壓力減少，那么剩余鑄件可以在該容器開始Tsolution。然后鑄件被轉移到浸泡爐繼續解決熱處理或在特殊情況下，水淬。 參考書目 [1] H.V. Atkinson, S. Davies, Fundamental Aspects of Hot Isostatic Pressing: An Overview, Metallurgical and Materials Transactions A, Vol. 31A, December 2000,pp. 2981-3000. [2] H.V. Atkinson, B.A. Rickinson, Hot Isostatic Processing, Adam Hilger, Bristol, UK,1991. [3] Q.G. Wang, D. Apelian, D.A. Lados, Fatigue Behavior of A356-T6 Aluminum Cast Alloys. Part I. Effect of Casting Defects, Journal of Light Metals 1, 2001, pp. 73-84. [4] C.S.C Lei, W.E. Frazier, E.W. Lee, The Effect of Hot Isostatic Pressing on CastAluminum, Journal Of Metals, November 1997, pp. 38-39. [5] J.C. Hebeisen, B.M. Cox, J. Turonek, R. Stack, The Effect of Densal Processing on the Properties of a Cast Aluminum Steering Knuckle, SAE Technical Publication,2002. [6] S.J. Mashl, J.C. Hebeisen, D. Apelian, Q.G. Wang, Hot Isostatic Pressing of A356 and 380/383 Aluminum Alloys: An Evaluation of Porosity, Fatigue Properties and Processing Costs, SAE Technical Publication #2000-01-0062. [7] M.M. Diem, S. Mashl, R. Sisson, Cost Effective Densification of Critical Application Aluminum through Simultaneous Densal? and Solution Heat Treatment. Part 1 Testing Industrial Castings, TBA. [8] C.R. Brooks, ASM Handbook, vol. 4, ASM International, Materials Park, OH, 1991,pp. 823-879. [9] S, Shivkumar, C. Keller, D. Apelian, Aging Behavior in Cast Al-Si-Mg Alloys,American Foundrymen’s Society Transactions, Vol. 90, No. 179, pp. 905-911. [10] D. Apelian, S. Shivkumar, S. Sigworth, Fundamental Aspects of Heat Treatment of Cast Al-Si-Mg Alloys, American Foundrymen’s Society Transactions, vol. 89, No. 137, pp. 727-742. [11] C, Bergmann, HIP Quenching in 2000 Bar Argon Gas, Metal Powder Report, October 1990, pp. 669-671. [12] F.T. Wall, Chemical Thermodynamics,W. H. Freeman and Company, San Francisco , CA, 1958. 附件2：外文原文（復印件） Development of a combined hot isostatic pressing and solution heat-treat process for the cost effective densification of critical aluminum castings The use of A356 (7%Si, 0.4%Mg) aluminum castings in the automotive industry is ncreasing due to the high shape complexity and the good strength-to-weight ratios that an be obtained with these parts. However, these parts in the as-cast condition are restricted in the applications in which they can be employed due to poor mechanical properties. These poor mechanical properties stem from two fundamental issues of the alloy in the as-cast condition. The first issue with these castings is caused by inhomogeneity in the casting alloy during solidification. This non-uniformity is caused by inconsistent cooling within the mold and leads to an uneven dispersion of coarsely formed precipitates in the alloy matrix. This in turn leads to poor tensile properties in the as-cast condition. The second issue inherent in as-cast microstructure is porosity. This porosity is classified as two distinct varieties, shrinkage porosity and gas porosity. Shrinkage porosity is caused by the volume of the liquid metal being greater than the volume of the solid metal. Gas porosity is caused by the high solubility of hydrogen in the liquid aluminum melt and the tendency for the hydrogen to come out of solution as temperature is reduced. Porosity is detrimental to the ductility, fracture toughness and fatigue behavior of the casting. Fortunately, for the casting industry, the issues inherent in the as-cast condition can be alleviated with post casting processing. Solution heat treating followed by aging is employed to refine the microstructure of the alloy and improve mechanical and physical properties. A densification process can eliminate the porosity in the casting. Heat treatment for cast aluminum alloys starts with a thermal process to solutionize the alloy matrix, known as solution heat treatment, or solutionizing. Solution heat treatment uses an elevated temperature heat treatment to dissolve the second phase precipitates, change the morphology of the eutectic silicon phase and make the primary phase a homogeneous solid solution. In the case of A356, the precipitates are Mg2Si. In order to prevent the Mg2Si particulates from again precipitating out of solution, a rapid quench is employed. Quenching the castings also insures that the homogenization that results from the solutionizing step is maintained. To attain maximum strength in the casting a precipitation-hardening or aging heat treatment is employed. Artificial aging takes place at slightly elevated temperatures, 165°C, while natural aging occurs at room temperature. The homogenization attained in the previous steps insures a uniform dispersion of the particulates grown in the aging step. Artificial aging to reach maximum strength deems the temper of the casting as T6, where natural aging gives the casting the temper designation T4. Hot isostatic pressing, or HIP, is typically performed before heat treatment and is a means of eliminating the porosity in castings. HIP surrounds the casting with a pressurized gas, which applies a hydrostatic force to the surface of the casting while at elevated temperature to facilitate material flow. The dominant densification mechanism in the casting during the initial stages of the HIP process is plastic flow. As castings spend additional time at maximum temperature and pressure the dominant densification mechanisms change, first to power-law creep, then to diffusional creep mechanisms (Nabarro-Herring, and Coble creep). The overall effect is the "welding" of isolated porosity within the casting [Atkinson]. Due to the time intensive nature of the HIP process, several variants of the original process have been developed to maximize the returns of the HIP process while minimizing process time and cost for the production of critical aluminum castings. Liquid hot isostatic pressing (LHIP) uses a heated incompressible liquid as the pressurizing media [Chandley]. The guiding principle behind this manufacturing process states that the majority of the time spent in the traditional gas HIP process is spent pressurizing and depressurizing the compressible gas media. In the LHIP process, the castings are immersed in the liquid salt bath and the entire salt bath container is pressurized via a hydraulic ram very quickly. By this method, maximum pressure can be reached in seconds rather then the several hours required in the HIP process. Furthermore, this process could be integrated into a continuous casting process [Chandley]. However, time spent at peak pressure for an A356 casting in the LHIP process is only about thirty seconds [Romano et al.], which does not allow any of the previously mentioned timedependant creep mechanisms to occur. Bodycote PLC has taken another approach to reducing the cost of the HIP process for aluminum castings. The Densal? process is a proprietary HIP process that has tailored the HIP process specifications and hardware specifically for aluminum castings. Time spent at temperature and pressure allows diffusional creep mechanisms to take place. It has been estimated that the Densal? process reduces the cost of HIP for aluminum castings by as much as seventy percent [Mashl et al.]. However, further gains in Densal? process economy may be possible. Due to the similarity of the process temperatures of solution heat treatment and the Densal? process, integrating these two processes could yield even further reduction in the cost of HIP and heat treatment for aluminum castings. The purpose of this thesis is to develop and evaluate the feasibility of this combined Densal? + solutionizing process. The bulk of the work completed is included here as two papers to be submitted for publication. Each paper is a stand-alone work with separate abstract, introduction, procedure, results and discussion, conclusion and reference sections. The first paper included as Chapter 2 presents the experimental results of the process combination of Densal? and solution heat treatment on several Al-Si-Mg commercial castings. The second paper, Chapter 3, presents the results of the theoretical energy calculations of the combined process versus the individual processes of Densal?followed by subsequent heat treatment. Aluminum casting represents an inexpensive method of producing parts with high shape complexity, excellent strength-to-weight ratios, and good corrosion resistance. For these reasons the use of aluminum castings in the automotive industry is on the rise. However, most aluminum alloys in the as-cast condition do not display the mechanical properties necessary for many applications, and therefore require subsequent heat treatment to optimize the microstructure of the alloy [1]. Furthermore, with the increased use of aluminum castings in cyclically stressed applications such as automotive suspension systems, maximizing the fatigue life of the heat-treated components becomes increasingly important. Densification, or the elimination of porosity inherent in the castings, is paramount in the production of fatigue-resistant parts, as pores are most often the fatigue-limiting characteristic in the casting. [2-6]. To date, microstructural refinement though heat treatment and fatigue-performance optimization through densification are completed as two independent processes. In the case of most Al-Si alloys, the heat treatment manifests itself as an often lengthy solutionizing step, followed immediately by a rapid quench and a subsequent controlled age [1,7]. According to ASM International, heat treatment can take upward of eighteen hours to achieve a T6 condition for most Al-Si alloys [1]. Novel techniques of eutectic silicon modification do significantly reduce the solution heat treatment time, but densification steps are still required to improve the fatigue performance of the casting [9]. To this end, hot isostatic pressing (HIP) performed before the heat treatment process has proven to be an effective means of increasing the fatigue life of critical application parts by eliminating the shrinkage and gas porosities inherent in the casting. HIPed parts can see as much as an order of magnitude increase in fatigue life when compared to identical un-HIPed samples [2-6]. The HIP process surrounds the castings with a pressurized gas that imparts a hydrostatic stress on the component [10,11]. This compressive stress, in tandem with elevated temperature, shrinks and heals potential stress-intensifying pores. Initial densification occurs within the casting through time independent plastic flow. Then, under the conditions of time at elevated temperature and pressure, complete densification occurs via diffusional creep mechanisms [10,11]. The micrographs included below show the effects of HIP densification. The pores, marked with arrows, in the un-HIPed samples (Figure 1) are eliminated in the HIPed sample (Figure 2). Figure 1 – Cast Al-Si-Mg alloy in T6 condition; arrows show porosity Figure 2 – Cast Al-Si-Mg alloy in HIPed T6 condition; no evidence of porosity Currently, HIP is an independent process that increases the manufacturing cost of castings. In order to minimize this cost for aluminum castings, Bodycote PLC has developed a proprietary process known as Densal?. Densal?optimizes the HIP process and hardware specifically for aluminum castings and represents an advancement in the cost reduction of this process [6]. One of the most cost-effective current process for the production of critical application castings is the Densal? process followed by T6 heat treatment [6], yet it remains that while Densal? is a value-added process, costs in both time and energy are incurred from its use. Due to the similarity of the peak temperature in both the HIP cycle and the solutionizing soak portion of the heat treat cycle, further integration of the two processes could save significant time and energy. There are difficulties inherent in this proposed combination. First, rapid quenching from the HIP vessel is currently not feasible due to the high pressure inherent in the HIP process. Secondly, even with eutectic-modification of alloys, the time at dwell temperature in the HIP vessel is usually not long enough for complete solutionizing. The goal of this study is to investigate the feasibility of a combined commercial Densal?/solution heat treat process. This will be accomplished by designing and implementing an experimental combined process. Next, the effects of the combined process on the microstructure and tensile and fatigue properties of industrial castings will be investigated. A manufacturing procedure has been developed to test the feasibility of a combined HIP/solution heat treatment. The process modifies current HIP hardware to allow full solution heat treatment in the HIP vessel as well as the ability to quench from the solutionizing temperature. The thermal profile that a casting is subjected to during the combined process will be identical to that seen by a casting undergoing the independent solution heat treatment. Specifically, the temperature of the castings will be raised to the solution temperature, maintained for a certain dwell time, and then rapidly dropped via a traditional water quench. Going on concurrently to the solutionizing however will be the densification process. At the same time as the temperature of the casting is raised, the pressure of the gaseous media surrounding the casting will also rise to a prescribed value. This pressure will be only be maintained for the length of the standard Densal? dwell time and not for the entire solutionizing time. Pressure will be reduced while solution temperature is maintained and the remainder of the solutionizing time will be fulfilled. One of the major questions that needed to be addressed to determine the feasibility of this combined process was whether the HIP furnace used had the sufficient power to overcome the adiabatic cooling that occurs in the vessel when the pressurized is vented. This issue becomes increasingly important when the heat transfer between the castings and the pressurized gas is considered. The operating pressure in the HIP vessel insures that this rate of heat transfer between the pressurized gas and the castings is on the order of ~100 W/m2 K [12]. However, if the furnace can maintain the casting at the solutionizing temperature, Tsolution, while the pressure within the vessel is reduced, then the vessel can be opened with the castings remaining at Tsolution. This would then allow the castings to either be transferred to a soak furnace to continue the solution heat treatment or in special cases, water quenched. References [1] H.V. Atkinson, S. Davies, Fundamental Aspects of Hot Isostatic Pressing: An Overview, Metallurgical and Materials Transactions A, Vol. 31A, December 2000,pp. 2981-3000. [2] H.V. Atkinson, B.A. Rickinson, Hot Isostatic Processing, Adam Hilger, Bristol, UK,1991. [3] Q.G. Wang, D. Apelian, D.A. Lados, Fatigue Behavior of A356-T6 Aluminum Cast Alloys. Part I. Effect of Casting Defects, Journal of Light Metals 1, 2001, pp. 73-84. [4] C.S.C Lei, W.E. Frazier, E.W. Lee, The Effect of Hot Isostatic Pressing on CastAluminum, Journal Of Metals, November 1997, pp. 38-39. [5] J.C. Hebeisen, B.M. Cox, J. Turonek, R. Stack, The Effect of Densal Processing on the Properties of a Cast Aluminum Steering Knuckle, SAE Technical Publication,2002. [6] S.J. Mashl, J.C. Hebeisen, D. Apelian, Q.G. Wang, Hot Isostatic Pressing of A356 and 380/383 Aluminum Alloys: An Evaluation of Porosity, Fatigue Properties and Processing Costs, SAE Technical Publication #2000-01-0062. [7] M.M. Diem, S. Mashl, R. Sisson, Cost Effective Densification of Critical Application Aluminum through Simultaneous Densal? and Solution Heat Treatment. Part 1 Testing Industrial Castings, TBA. [8] C.R. Brooks, ASM Handbook, vol. 4, ASM International, Materials Park, OH, 1991,pp. 823-879.