購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
二、The injection and Compression Molding
Injection molding si principally used for the production of the thermoplastic parts, although some progress has been made in developing a method for injection molding some thermosetting materials. The problem of injecting a melted plastic into a mold cavity form a reservoir of melted material has been extremely difficult to solve for thermosetting plastics which cure and harden under such conditions within a few minutes. The principle of injection molding is quite similar to that of die-casting. The process consists of feeding a plastic compound in powdered or granular form from a hopper through metering and melting stages and then injecting it into a mold. After a brief coolling period, the mold is opened and the solidified part ejected. Injection-molding machines can be arranged for manual operation, automatic single-cucle operation, and full automatic operation. The advantage of injection molding are:
(i) a high molding speed adapted for mass production is possible;
(ii) there is a wide choice of thermoplastic materials providing a variety of usefull properties;
(iii) it is possible to mold threads, undercuts, side holes, and large thin sections.
Several methods are used to force or inject the melted plastic into the mold. The most commonly used system in the larger machines is the in-line reciprocating screw.The screw acts as a combination and plasticizing unit.As the plastic is fed to the rotating screw,it passes through three zones as shown: feed,compression, and metering. After the feed zone, the screw-flight depth is gradually reduced,forcing the plastic to compress. The work is converted to heat by shearing the plastic, making it a semifluid mass. In the metering zone, additional heat is applied by conduction from the barrel surface. As the chamber in front of the screw becomes filled, it forces the screw back, tripping a limit switch that activates a hydraulic cylinder that forces the screw forward and injects the fluid plastic into the closed mold.An antiflowback valve prevents plastic under pressure from escaping back into the screw flights.
The clamping force that a machine is capable of exerting is part of the size designation and is measured in tons. A rule-of-thumb can be used to determine the tonnage required for a particular job. It is based on two tons of clamp force per square inch of projected area. If the flow pattern is difficult and the parts are thin,this may have to go to three or four tons.
Many reciprocating - screw machines are capable of handing thermosetting plastic materials.Previously these materials were handled by compression or transfer molding.Thermosetting materials cure or polymerize in the mold and are ejected hot in the range of 375℃～410℃.Thermoplastic parts must be allowed to cool in the mold in order to remove them without distortion.Thus thermosetting cycles can be faster.Of course the mold must be heated rather than chilled,as with thermoplastics.
The importance of Injecting the mold are :
⑴、Plastics have the density small, the quality light, the specific tenacity big, the insulating property good, the dielectric loss low, the chemical stability strong, the formation productivity high and the price inexpensive and so on the merits, obtained day by day the widespread application in the national economy and people's daily life each domain, as early as in the beginning of 1990s, the plastic annual output already surpassed the steel and iron and the non-ferrous metal annual output sum total according to the volume computation.In mechanical and electrical (for example so-called black electrical appliances), domains and so on measuring appliance, chemical, the automobile and astronautics aviation, the plastic has become the metal the good substitution material, had the metal material plastic tendency.
⑵、Take the automobile industry as the example , as a result of the automobile lightweight, the low energy consumption development request, the automobile spare part material constitution occurred obviously has modelled the band steel the change, at present our country automobile plastic accounts for 5% which the automobile was self-possessed to 6%, but overseas has reached 13%, forecast according to the expert, the automobile plastic bicycle amount used will also be able further to increase.On modern vehicles, regardless of is outside installs the assorted items, the internal installation assorted items, the function and the structural element, all may use the plastic material, outside installs the assorted items to have the bumper, the fender, the wheel hub cap, the air deflector and so on; After the internal installation assorted items have in the display board, the vehicle door the board, the vice-display board, the sundry goods box lid, the chair, the guard shield and so on; The function and the structural element have the fuel tank, the radiator header, the spatial filter hood, the fan blade and so on.Statistics have indicated, our country in 2000 automobile output more than 200 ten thousand, the vehicle amounted to 1,380,000 tons with the plastic.Looked from the domestic and foreign automobile plastic application situation that, the automobile plastic amount used already became one of weight automobile production technical level symbols.
⑶、Injection of a molding formation as plastic workpiece most effective formation methods because may by one time take shape each kind of structure complex, the size precise and has the metal to inlay a product, and the formation cycle is short, may by mold multi-cavities, the productivity be high, when mass productions the cost isvery inexpensive, easy to realize the automated production, therefore holds the extremely important status in the plastic processing profession.Statistics have indicated, plastic mold composition all molds (including metal pattern) 38.2%, the plastic product gross weight about 32% is uses in injecting the formation, 80% above engineering plastics product all must use the injection formation way production. 4. counts according to the customs, our country in 2000 altogether imported mold 977,000,000 US dollars, in which plastic molding forms altogether 550,000,000 US dollars, occupied for 56.3%,2001 years altogether to import mold 1,112,000,000 US dollars, in which plastic molding forms altogether 616,000,000 US dollars, accounted for 55.4%.From the variety, the import volume biggest is the plastic molding forms.
⑷、Counts according to the customs, our country in 2000 altogether imported mold 977,000,000 US dollars, in which plastic molding forms altogether 550,000,000 US dollars, occupied for 56.3%, 2001 years altogether to import mold 1,112,000,000 US dollars, in which plastic molding forms altogether 616,000,000 US dollars, accounted for 55.4%.From the variety, the import volume biggest is the plastic molding forms.
In compression molding the palstic material as powder or preforms is placed into a heated steel mold cavity,Since the parting surface is in a horizontal plane ,the upper half of the mold descends vertically.It closes the mold cavity and pressures for a predetermined period.A pressure of from 2 to 3 tons square inch and a temperaure at approximately 350F converts the plastic to a semiliquid which flows to all parts of the mold cavity.Usually from 1 to 15 minutes is required for curing,altough a recently developed alkyd plastic will cure in less than 25 secends. The mold is then opended and the molded part removed.If metal insers are desired in the parts,they should be placed in the mold cavity on pins or in the holes before the plastic is loaded.Also, the preforms should be preheated before loading into the mold cavity to eliminate gases,inprove flow,and decrease curing time.Dieletric heating is a convenient method of heating the preforms.
Since the plastic material is placed directly into the mold cavity,the mold itself can be simpler than those used for other molding precesses.Gates and sprues are unnecessary.This also results in a saving in material,because trimmed-off gates and sprues would be a complete loss of the thermosetting plastic.The press require the full attention of one operator.However,several smaller presses can be operated by one operator. The presses are conveniently located so the operator can easilymove from one to the next.By the time he gets around to a particular press again,that mold will be ready to open.the thermosetting plastics which harden under heat and pressure are suitable for compression molding and transfer molding.It is not practical to moid shermoplastic materials by these methods,since the molds would have to be alternately heated and cooled.In order to harden and eject thermoplastic parts form the mold,cooling would be necessary.
Types of molds for compression molding.The molds used for compression molding are classified into four basic types, namely ,positive molds,landed positive mold,flash-type molds,and semipositive molds.In a positive mold the plunger on the upper mold enters the lower mold cavity.since there are no lands or stops on the lower die ,the plunger completely trap the plastic material and descends with full pressure on the charge.A dense part with good electrical and physical properties is produced.The amount of plastic placed in the die cavity must be accurately measured,since it determines the thickness of the part .A landed positive mold is similar to a positive mold except that lands are added to stop the travel of the plunger at predetermined point.In this case,the lands absorb some of the pressure that should be exerted on the parts.The thickness of the parts will be accurately controlled,but the density may vary cansideraby.In a flash-type mold,flash redges are added ti the top and bottom molds.As the upper mold exerts pressure on the plastic,excess material is forced out between the flash ridges where it forms flash.This flash is further compressed.becomes hardened,and finally stops the downard thavel of the upper mold.A slight excess of the plastic material is always chared to ensure sufficient pressurs to produce a dense molded part.This type of mold is widely used because it is comparatively easy to construct and it controls thickness and density within colse limits.The semipositive mold is a combination od the flash type and landed posive molds.In addition to the flash ridges,a land is employed to restrict the travel of the upper mold.
畢業設計（論文）
設計（論文）題 目 階梯圓桶落料拉深復合模具設計
學 生 姓 名
指 導 教 師
20XX年 1 月 4 日
學院（系） 數控技術 專業
畢 業 設 計論 文 任 務 書
一、題目及專題：
1、題目 沖壓模具設計
2、專題 階梯圓筒落料拉深模具設計
二、課題來源及選題依據
課題來源：企業開發研制產品需要。
選題依據：根據學生所學專業及教學大綱要求，結合相關企業實際生產需要及設計模式，促使學生將所學專業基礎知識及專業知識具體應用到實踐中，培養其理論聯系實際的能力。
三、本設計（論文或其他）應達到的要求：
1．根據零件的使用條件、技術要求、形狀和尺寸，確定該零件的冷沖壓工藝方案（包括排樣圖）；
2．選擇各工序沖壓設備，填寫沖壓工藝過程卡；
3．設計本工序的工裝設備（模具）；
4．繪制全套模具圖（工序圖、排樣圖、裝配圖和零件圖）；
5．撰寫設計計算說明書一份，字?jǐn)?shù)約10000字符。
四、接受任務學生：
班 姓名
五、開始及完成日期：
自20 年 11 月 05 至 20 年1月04日
六、設計（論文）指導（或顧問）：
指導教師 簽名
簽名
教研室主任
〔學科組組長研究所所長〕 簽名
院長(系主任) 簽名
年 月 日
摘要
此次畢業設計是由XX老師親自指導，設計一副簡單的復合模具，經過數個月的設計，基本完成此次設計的任務。此副模具主要是階梯圓筒形零件的設計，采用落料﹑拉深兩道工序相結合的復合模，本人經查閱相關書籍﹑資料以隊此副模具所用到的相關公式﹑數據做出了一個準確的依據。
此副模具的設計一共分為四章，和其他模具的設計一樣，首先第一章是對零件進行了工藝分析，接著對工藝方案進行了比較，最終確定采用先落料拉深后切邊的工藝方案，然后畫工序圖﹑經過計算選擇沖壓設備。第二章是選擇沖模類型以及結構形式，接著是一些模具設計的相關數據計算。第三章是對模具凸模﹑凹模加工工藝過程以及加工工藝方案的確定，最后填寫凸凹模加工工藝規程卡以及編制凸模數控加工程序。第四章是設計總結﹑謝辭以及參考文獻。
本人在設計過程中得到了其他同學的大力支持，并有XX老師的息心指導，在此表示誠懇的感謝。由于本人水平有限，此次設計難免還存在一些缺點和錯誤，懇請閱讀者批評指正。
目 錄
第1章 沖壓工藝設計······························1
1.1 零件的工藝分析····································1
1.2 制定沖壓工藝方案·································3
1.3 畫工序圖··········································4
1.4 初選沖壓設備······································6
1.5編制沖壓工藝卡·····································8
第2章 沖壓模具設計·····························10
2.1 沖模類型及結構形式·······························10
2.2 模具設計計算·····································10
第3章 模具主要零件加工工藝設計·················14
3.1 制定凸凹模加工工藝過程···························14
3.2 填寫凸凹模加工工藝規程卡·························16
3.3 編制凸?；虬寄?shù)控加工程序·······················19
第4章 設計總結·································21
致謝············································22
參考文獻········································23
汽車開發周期從40個月縮短到4個月。
一、
1、模具在工業發展中的地位
采用模具生產零部件，具有生產效率高、質量好、成本低、節約能源和原材料等一系列優點，用模具生產制件所具備的高精度、高復雜程度、高一致性、高生產率和低消耗，是其他加工制造方法所不能比擬的。已成為當代工業生產的重要手段和工藝發展方向?，F(xiàn)代經濟的基礎工業。現代工業品的發展和技術水平的提高，很大程度上取決于模具工業的發展水平，因此模具工業對國民經濟和社會發展將起越來越大的作用。1989年3月國務院頒布的《關于當前產業政策要點的決定》中，把模具列為機械工業技術改造序列的第一位、生產和基本建設序列的第二位(僅次于大型發電設備及相應的輸變電設備)，確立模具工業在國民經濟中的重要地位。1997年以來，又相繼把模具及其加工技術和設備列入了《當前國家重點鼓勵發展的產業、產品和技術目錄》和《鼓勵外商投資產業目錄》。經國務院批準，從1997年到2000年，對80多家國有專業模具廠實行增值稅返還70%的優惠政策，以扶植模具工業的發展。所有這些，都充分體現了國務院和國家有關部門對發展模具工業的重視和支持。目前全世界模具年產值約為600億美元，日、美等工業發達國家的模具工業產值已超過機床工業，從1997年開始，我國模具工業產值也超過了機床工業產值。
模具是大批量生產同形產品的工具，是工業生產的主要工藝裝備。
據統計，在家電、玩具等輕工行業，近90％的零件是綜筷具生產的；在飛機、汽車、農機和無線電行業，這個比例也超過60％。例如飛機制造業，某型戰斗機模具使用量超過三萬套，其中主機八千套、發動機二千套、輔機二萬套。從產值看，80年代以來，美、日等工業發達國家模具行業的產值已超過機床行業，并又有繼續增長的趨勢。據國際生產技術協會預測，到2000年，產品盡件粗加工的75%、精加工的50％將由模具完成；金屬、塑料、陶瓷、橡膠、建材等工業制品大部分將由模具完成，50％以上的金屬板材、80％以上的塑料都特通過模具轉化成制品。
2、模具的歷史發展
模具的出現可以追溯到幾千年前的陶器和青銅器鑄造，但其大規模使用卻是隨著現代工業的掘起而發展起來的。
19世紀，隨著軍火工業(槍炮的彈殼)、鐘表工業、無線電工業的發展，沖模得到廣泛使用。二次大戰后，隨著世界經濟的飛速發展，它又成了大量生產家用電器、汽車、電子儀器、照相機、鐘表等零件的最佳方式。從世界范圍看，當時美國的沖壓技術走在前列——許多模具先進技術，如簡易模具、高效率模具、高壽命模具和沖壓自動化技術，大多起源于美國；而瑞士的精沖、德國的冷擠壓技術，蘇聯對塑性加工的研究也處于世界先進行列。50年代，模具行業工作重點是根據訂戶的要求，制作能滿足產品要求的模具。模具設計多憑經驗，參考已有圖紙和感性認識，對所設計模具零件的機能缺乏真切了解。從1955年到1965年，是壓力加工的探索和開發時代——對模具主要零部件的機能和受力狀態進行了數學分橋，并把這些知識不斷應用于現場實際，使得沖壓技術在各方面有飛躍的發展。其結果是歸納出模具設計原則，并使得壓力機械、沖壓材料、加工方法、梅具結構、模具材料、模具制造方法、自動化裝置等領域面貌一新，并向?qū)嵱没姆较蛲七M，從而使沖壓加工從儀能生產優良產品的第一階段。
進入70年代向高速化、啟動化、精密化、安全化發展的第二階段。在這個過程中不斷涌現各種高效率、商壽命、高精度助多功能自動校具。其代表是多達別多個工位的級進模和十幾個工位的多工位傳遞模。在此基礎上又發展出既有連續沖壓工位又有多滑塊成形工位的壓力機—彎曲機。在此期間，日本站到了世界最前列——其模具加工精度進入了微米級，模具壽命，合金工具鋼制造的模具達到了幾千萬次，硬質合金鋼制造的模具達到了幾億次p每分鐘沖壓次數，小型壓力機通常為200至300次，最高為1200次至1500次。在此期間，為了適應產品更新快、用期短(如汽車改型、玩具翻新等)的需要，各種經濟型模具，如鋅落合金模具、聚氨酯橡膠模具、鋼皮沖模等也得到了很大發展。
從70年代中期至今可以說是計算機輔助設計、輔助制造技術不斷發展的時代。隨著模具加工精度與復雜性不斷提高，生產周期不斷加快，模具業對設備和人員素質的要求也不斷提高。依靠普通加工設備，憑經驗和手藝越來越不能滿足模具生產的需要。90年代以來，機械技術和電子技術緊密結合，發展了NC機床，如數控線切割機床、數控電火花機床、數控銑床、數控坐標磨床等。而采用電子計算機自動編程、控制的CNC機床提高了數控機床的使用效率和范圍。近年來又發展出由一臺計算機以分時的方式直接管理和控制一群數控機床的NNC系統。
隨著計算機技術的發展，計算機也逐步進入模具生產的各個領域，包括設計、制造、管理等。國際生產研究協會預測，到2000年，作為設計和制造之間聯系手段的圖紙將失去其主要作用。模具自動設計的最根本點是必須確立模具零件標準及設計標準。要擺脫過去以人的思考判斷和實際經驗為中心所組成的設計方法，就必須把過去的經驗和思考方法，進行系列化、數值化、數式化，作為設計準則儲存到計算機中。因為模具構成元件也干差萬別，要搞出一個能適應各種零件的設計軟件幾乎不可能。但是有些產品的零件形狀變化不大，模具結構有一定的規律，放可總結歸納，為自動設計提供軟件。如日本某公司的CDM系統用于級進模設計與制造，其中包括零件圖形輸入、毛坯展開、條料排樣、確定模板尺寸和標準、繪制裝配圖和零件圖、輸出NC程序(為數控加工中心和線切割編程)等，所用時間由手工的20%、工時減少到35小時；從80年代初日本就將三維的CAD／CAM系統用于汽車覆蓋件模具。目前，在實體件的掃描輸入，圖線和數據輸入，幾何造形、顯示、繪圖、標注以及對數據的自動編程，產生效控機床控制系統的后置處理文件等方面已達到較高水平；計算機仿真(CAE)技術也取得了一定成果。在高層次上，CAD／CAM／CAE集成的，即數據是統一的，可以互相直接傳輸信息．實現網絡化。目前．國外僅有少數廠家能夠做到。
3、模具的發展趨勢
（1）模具軟件功能集成化
模具軟件功能的集成化要求軟件的功能模塊比較齊全，同時各功能模塊采用同一數據模型，以實現信息的綜合管理與共享，從而支持模具設計、制造、裝配、檢驗、測試及生產管理的全過程，達到實現最佳效益的目的。如英國Delcam公司的系列化軟件就包括了曲面/實體幾何造型、復雜形體工程制圖、工業設計高級渲染、塑料模設計專家系統、復雜形體CAM、藝術造型及雕刻自動編程系統、逆向工程系統及復雜形體在線測量系統等。集成化程度較高的軟件另外還包括：Pro/ENGINEER、UG和CATIA等。國內有上海交通大學金屬塑性成型有限元分析系統和沖裁模CAD/CAM系統；北京北航海爾軟件有限公司的CAXA系列軟件；吉林金網格模具工程研究中心的沖壓模CAD/CAE/CAM系統等。
（2）模具設計、分析及制造的三維化
傳統的二維模具結構設計已越來越不適應現代化生產和集成化技術要求。模具設計、分析、制造的三維化、無紙化要求新一代模具軟件以立體的、直觀的感覺來設計模具，所采用的三維數字化模型能方便地用于產品結構的CAE分析、模具可制造性評價和數控加工、成形過程模擬及信息的管理與共享。舉個例子如Pro/ENGINEER、UG和CATIA等軟件具備參數化、基于特征、全相關等特點，從而使模具并行工程成為可能。另外，Cimatran公司的Moldexpert，Delcam公司的Ps-mold及日立造船的Space-E/mold均是3D專業注塑模設計軟件，可進行交互式3D型腔、型芯設計、模架配置及典型結構設計。澳大利亞Moldflow公司的三維真實感流動模擬軟件MoldflowAdvisers已經受到用戶廣泛的好評和應用。國內有華中理工大學研制的同類軟件HSC3D4.5F及鄭州工業大學的Z-mold軟件。面向制造、基于知識的智能化功能是衡量模具軟件先進性和實用性的重要標志之一。如Cimatron公司的注塑模專家軟件能根據脫模方向自動產生分型線和分型面，生成與制品相對應的型芯和型腔，實現模架零件的全相關，自動產生材料明細表和供NC加工的鉆孔表格，并能進行智能化加工參數設定、加工結果校驗等。
（3）模具軟件應用的網絡化趨勢
隨著模具在企業競爭、合作、生產和管理等方面的全球化、國際化，以及計算機軟硬件技術的迅速發展，網絡使得在模具行業應用虛擬設計、敏捷制造技術既有必要，也有可能。美國在其《21世紀制造企業戰略》中指出，到2006年要實現汽車工業敏捷生產/虛擬工程方案，使汽車開發周期從40個月縮短到4個月。AA