購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814

黑龍江工程學院本科生畢業設計 致 謝 在本文即將完成之際，首先感謝我的指導老師王永梅老師，從選題到設計的展開到設計的完成，一直得到王老師的支持和鼓勵，她淵博的學識、嚴謹?shù)闹螌W(xué)態度都給我留下了深刻的印象。通過這次的設計，我更深刻地了解了機械設計、機械制造的各方面知識，對汽車設計有了全新且比較全面的深刻認識，達到了前所未有的高度，并鍛煉了獨立思考解決問題的能力。再次向王老師表示衷心的感謝！ 感謝幫助我的所有老師和同學，他們在設計過程中給我提出了寶貴建議和CAD的指導。感謝宿舍的朋友一直以來對我的關心和支持。感謝汽車工程系所有老師和同學的幫助和勉勵。同窗之誼，終生難忘！ 感謝我的家人多年來對我無微不至的關懷、始終如一的支持，感謝他們對我的鼓勵和生活上的諸多照顧，感謝他們督促我接受良好的教育。 最后，向參加設計審閱、答辯的專家和老師表示感謝。 8 附 錄A 外文文獻 The structural characteristics of non-independent suspension on both sides of the wheel is an integral frame connected by the wheels together with the adoption of flexible suspension bridge hanging in the frame or body of the following. Non-independent suspension has a simple structure, low cost, high strength, easy maintenance, driving changes in the small front wheel alignment advantages, but because of its comfort and handling stability are poor, largely in the modern car is no longer in use more used in trucks and large passenger on. Independent suspension on each side of the wheel is individually through the elastic suspension is hanging in the frame or body below. The advantages are: light weight, reduced body shocks, and improve adhesion of the wheels on the ground; available small soft spring stiffness, improve vehicle comfort; can reduce engine position, car center of gravity is reduced, thereby improve the car's driving stability; about beating the wheel alone, independent of each other, can reduce the body's tilt and vibration. However, there are complex independent suspension, high cost and maintenance problem of inaccessibility. Modern cars are mostly used independent suspension, according to the different structure, independent wishbone suspension can be divided into longitudinal arm, multi-link, candle and McPherson suspension and so on. Arm Suspension means the horizontal plane in the car wheel independent suspension swing, according to the number of how many arm is divided into wishbone and single-arm suspension. Single-Arm has a simple structure, roll center height, with a strong anti-roll capability advantages. But with the increased speed of modern vehicles, roll center is too high will cause the wheel tread beats changes, tire wear increased, and in a sharp turn around the wheel vertical force when the transfer is too large, resulting in increased rear extraversion. Reduce rear-wheel cornering stiffness, resulting in a serious condition high-speed drift. Single-wishbone independent suspension in the rear suspension on a multi-application, but can not meet the requirements of high speed, the current limited application. Multi-link suspension are combined by the root pole position change control of the wheel suspension. Multi-link can wheel around the axis line with the vehicle at an angle within the swing axis is horizontal arm and vertical arm of the compromise, choose the right arm with the motor axis into a vertical line of the angle, can be varying degrees of access to wishbone suspension with the advantages of vertical arm, which can meet different performance requirements. Multi-link suspension of the main advantages are: the wheel tread and beating little change before the beam, both cars are in driving, braking status can be carried out by the driver of the Yi Tu smooth transition to its shortcomings in the automotive when the phenomenon of high-speed shaft swing. Mainly in the FR-link drive mode, and around the back axle of the integration (and the middle of the differential rigid connection) for use where, in the past to use more leaf spring support body, and now from the increased driving comfort considerations, multi-use Link back to say that the swing arm type and style, and use a good coil spring ride. Link in the left side of a pair, divided into upper and lower tie rod, as the lateral force transmission (car drivers) body, usually with a horizontal thrust bar again with the composition of the five-link form. Connect one end of the body lateral thrust rod, one end of the connecting axle, its purpose is to prevent the axle (or body) horizontal traverse. When the axle moves up and down because of the rough, the lateral thrust rod will be connected to contacts with the body axis, an art movement arc, through the General Assembly if the swing angle made between the axles and the body produces significant lateral relative motion, and the lower arm principle similar to the horizontal thrust rod longer than should be designed to reduce the swing angle. Link suspension and axle forming an integrated whole, the mass of the spring below, and not the independence movement around the wheel, so to face bumpy road vehicle impact energy generated by relatively large, poor ride comfort. So there arm methods, this approach is the only fixed-axle differential among left and right half shaft in the differential and universal joints located between the wheel and the center of its swing, used between the wheel and the frame Y-connection under the arm. "Y" at one end and a separate rigid wheel, the other two endpoints and the frame to connect and form a rotation axis. According to the rotation axis is parallel with the axle, swing arm type suspension is divided into full drag-type arm and half drag-style swing arm, parallel to the whole drag-style, non-parallel type is called semi-drag. Because comfort is the car one of the most important performance, and comfort with the body's natural vibration characteristics, whereas the body's natural vibration characteristics of a feature associated with the suspension. Therefore, the vehicle suspension is to ensure the comfort of the important parts. Meanwhile, the vehicle suspension as a frame (or body) and the axle (or wheel) to make the connection between the mechanical power transmission, it is important to ensure the safety of motor cars and parts. Therefore, the vehicle suspension components are often incorporated into the car as an important technical specifications of the table, as one of the indicators to measure the quality of cars. Active suspension is developed in the last ten years, a new type of computer-controlled suspension. It brings together mechanics and electronics, technical knowledge, is a more complex high-tech devices. For example, the installation of the French Citroen Sang Diya active suspension, the center of the car suspension system is a microcomputer, the suspension on five kinds of sensors were transmitted to the micro-computer speed, front wheel brake pressure, ride a fixed throttle pedal speed, body vertical amplitude and frequency, steering wheel angle and steering velocity data. Computer continuously receives the data and with pre-set threshold to compare, select the appropriate suspension state. Meanwhile, the microcomputer independent control of each wheel on the implementation of the components only by controlling the hydraulic shock absorber of changes within the tic, which can at any time, any wheels that meet the requirements of the suspension movement. Therefore, Sang Diya car a wide range of driving mode selection, drivers need only flip a deputy on the dashboard in the "normal" or "sport" button will automatically set the car's suspension in top condition, in order to The best comfort. Active suspension control of body movement with the function. When the car when braking or turning the inertia caused by the spring deformation, the active suspension forces will have to confront a force used to reduce the body position changes. 2000 Mercedes-Benz CL models such as Germany-based sports car, when the suspension when the vehicle turning sensor will immediately detect the body's tilt and lateral acceleration. Computer based on the sensor information, and pre-set threshold value of calculations to determine what position once the load will be added to the suspension on how to minimize body tilt. Wishbone independent suspension by upper and lower arm is so long, is divided into equal length wishbone and unequal length wishbone suspension of two. And other long-wishbone suspension in the wheel up and down beats, kingpin inclination to maintain the same, but the wheelbase change greatly (and similar single-Arm), resulting in severe tire wear, is now rarely used. The unequal length wishbone suspension, when properly selected to optimize the length of the upper and lower arm, and through a reasonable layout, you can make changes in tread and the front wheel alignment parameters were within acceptable limits to ensure the car good driving stability. Present unequal length wishbone suspension has been widely used in cars, front and rear suspension, the part of the sports car and the car's rear wheel has adopted this - suspension structure. Suspension role Suspension is an important vehicle in the assembly, it is to frame the flexibility to link with the wheel bearing on a variety of performance cars. In appearance, a car suspension only by a number of rods, cylinders and springs form, but do not think it is very simple, opposite a car suspension is more difficult to achieve the perfect vehicle assembly requirements, this is because both suspension to meet the car's comfort requirements, but also to meet the requirements of its handling and stability, while these two aspects are mutually antagonistic. For example, in order to achieve good comfort, requires much buffer vehicle vibration, the spring must be designed so soft, but, it is easy for the spring soft place car brake "nod", the "rise" and roll about serious adverse tendency is not conducive to the car turn easily lead to vehicle handling and instability. Therefore, if the suspension is poorly designed, will significantly affect the performance of automotive products (such as turning a heavy, swing, tire eccentric wear and affect tire life, etc.). ???? 附 錄B 中文翻譯 非獨立懸架的結構特點是兩側車輪由一根整體式車架相連，車輪連同車橋一起通過彈性懸架懸掛在車架或車身的下面。非獨立懸架具有結構簡單、成本低、強度高、保養容易、行車中前輪定位變化小的優點，但由于其舒適性及操縱穩定性都較差，在現代轎車中基本上已不再使用，多用在貨車和大客上。獨立懸架是每一側的車輪都是單獨地通過彈性懸架懸掛在車架或車身下面的。其優點是：質量輕，減少了車身受到的沖擊，并提高了車輪的地面附著力；可用剛度小的較軟彈簧，改善汽車的舒適性；可以使發動機位置降低，汽車重心也得到降低，從而提高汽車的行駛穩定性；左右車輪單獨跳動，互不相干，能減小車身的傾斜和震動。不過，獨立懸架存在著結構復雜、成本高、維修不便的缺點。現代轎車大都是采用獨立式懸架，按其結構形式的不同，獨立懸架又可分為橫臂式、縱臂式、多連桿式、燭式以及麥弗遜式懸架等。橫臂式懸架是指車輪在汽車橫向平面內擺動的獨立懸架，按橫臂數量的多少又分為雙橫臂式和單橫臂式懸架。單橫臂式具有結構簡單，側傾中心高，有較強的抗側傾能力的優點。但隨著現代汽車速度的提高，側傾中心過高會引起車輪跳動時輪距變化大，輪胎磨損加劇，而且在急轉彎時左右車輪垂直力轉移過大，導致后輪外傾增大。減少了后輪側偏剛度，從而產生高速甩尾的嚴重工況。單橫臂式獨立懸架多應用在后懸架上，但由于不能適應高速行駛的要求，目前應用不多。多連桿式懸架是由根桿件組合起來控制車輪的位置變化的懸架。多連桿式能使車輪繞著與汽車縱軸線成一定角度的軸線內擺動，是橫臂式和縱臂式的折衷方案，適當?shù)剡x擇擺臂軸線與汽車縱軸線所成的夾角，可不同程度地獲得橫臂式與縱臂式懸架的優點，能滿足不同的使用性能要求。多連桿式懸架的主要優點是：車輪跳動時輪距和前束的變化很小，不管汽車是在驅動、制動狀態都可以按司機的意圖進行平穩地轉向，其不足之處是汽車高速時有軸擺動現象。連桿式主要是在FR驅動方式，并且后車軸左右一體化(與中間的差速器剛性連接)的情況下使用的，過去多采用鋼板彈簧支撐車身，現在從提高行車平順性考慮，多使用連桿式和后面要說的擺臂式，并且使用平順性好的螺旋彈簧。連桿在左右兩側各有一對，分為上拉桿和下拉桿，作為傳遞橫向力(汽車驅動力)的機構，通常再與一根橫向推力桿一起組成五連桿式構成。橫向推力桿一端連接車身，一端連接車軸，其目的是為了防止車軸(或車身)橫向竄動。當車軸因顛簸而上下運動時，橫向推力桿會以與車身連接的接點為軸做畫圓弧的運動，如果擺動角度過大會使車軸與車身之間產生明顯的橫向相對運動，與下擺臂的原理類似，橫向推力桿也要設計得比較長，以減小擺動角。連桿式懸架與車軸形成一體，彈簧下方質量大，且左右車輪不能獨立運動，所以顛簸路面對車身產生的沖擊能量比較大，平順性差。因此出現了擺臂方式，這種方式是僅車軸中間的差速器固定，左右半軸在差速器與車輪之間設萬向節，并以其為中心擺動，車輪與車架之間用Y型下擺臂連接?！癥”的單獨一端與車輪剛性連接，另外兩個端點與車架連接并形成轉動軸。根據這個轉動軸是否與車軸平行，擺臂式懸架又分為全拖動式擺臂和半拖動式擺臂，平行的是全拖動式，不平行的叫半拖動式。 由于舒適性是轎車最重要的使用性能之一，而舒適性與車身的固有振動特性有關，而車身的固有振動特性又與懸架的特性相關。所以，汽車懸架是保證乘坐舒適性的重要部件。同時，汽車懸架做為車架(或車身)與車軸(或車輪)之間作連接的傳力機件，又是保證汽車行駛安全的重要部件。因此，汽車懸架往往列為重要部件編入轎車的技術規格表，作為衡量轎車質量的指標之一。 　　主動懸架是近十幾年發展起來的、由電腦控制的一種新型懸架。它匯集了力學和電子學的技術知識，是一種比較復雜的高技術裝置。例如裝置了主動懸架的法國雪鐵龍桑蒂雅，該車懸架系統的中樞是一個微電腦，懸架上的5種傳感器分別向微電腦傳送車速、前輪制動壓力、踏動油門踏板的速度、車身垂直方向的振幅及頻率、轉向盤角度及轉向速度等數據。電腦不斷接收這些數據并與預先設定的臨界值進行比較，選擇相應的懸架狀態。同時，微電腦獨立控制每一只車輪上的執行元件，通過控制減振器內油壓的變化產生抽動，從而能在任何時候、任何車輪上產生符合要求的懸架運動。因此，桑蒂雅轎車備有多種駕駛模式選擇，駕車者只要扳動位于副儀表板上的“正?！被颉斑\動”按鈕，轎車就會自動設置在最佳的懸架狀態，以求最好的舒適性能。 主動懸架具有控制車身運動的功能。當汽車制動或拐彎時的慣性引起彈簧變形時，主動懸架會產生一個與慣力相對抗的力，減少車身位置的變化。例如德國奔馳2000款CL型跑車，當車輛拐彎時懸架傳感器會立即檢測出車身的傾斜和橫向加速度。電腦根據傳感器的信息，與預先設定的臨界值進行比較計算，立即確定在什么位置上將多大的負載加到懸架上，使車身的傾斜減到最小。 雙橫臂式獨立懸架按上下橫臂是否等長，又分為等長雙橫臂式和不等長雙橫臂式兩種懸架。等長雙橫臂式懸架在車輪上下跳動時，能保持主銷傾角不變，但輪距變化大(與單橫臂式相類似)，造成輪胎磨損嚴重，現已很少用。對于不等長雙橫臂式懸架，只要適當選擇、優化上下橫臂的長度，并通過合理的布置，就可以使輪距及前輪定位參數變化均在可接受的限定范圍內，保證汽車具有良好的行駛穩定性。目前不等長雙橫臂式懸架已廣泛應用在轎車的前后懸架上，部分運動型轎車及賽車的后輪也采用這—懸架結構。 懸架作用 　　懸架是汽車中的一個重要總成，它把車架與車輪彈性地聯系起來，關系到汽車的多種使用性能。從外表上看，轎車懸架僅是由一些桿、筒以及彈簧組成，但千萬不要以為它很簡單，相反轎車懸架是一個較難達到完美要求的汽車總成，這是因為懸架既要滿足汽車的舒適性要求，又要滿足其操縱穩定性的要求，而這兩方面又是互相對立的。比如，為了取得良好的舒適性，需要大大緩沖汽車的震動，這樣彈簧就要設計得軟些，但彈簧軟了卻容易使汽車發生剎車“點頭”、加速“抬頭”以及左右側傾嚴重的不良傾向，不利于汽車的轉向，容易導致汽車操縱不穩定等。因此，如果懸架結構設計不當，就會大大影響汽車產品的使用性能(如轉向沉重、擺振、輪胎偏磨、影響輪胎使用壽命等)。 SY-025-BY-2 畢業設計（論文）任務書 學生姓名 王萌 院系 汽車與交通工程學院 專業、班級 車輛工程B07-2 指導教師姓名 王永梅 職稱 講師 從事 專業 車輛工程 是否外聘 □是■否 題目名稱 礦用越野車懸架系統的設計 一、設計（論文）目的、意義 　 礦用越野車在我國應用較廣，其中懸架是礦用越野車的的主要部件，其設計的成功與否決定著車輛的行駛平順性和操縱穩定性、舒適性等多方面的設計要求。設計出結構簡單、工作可靠、造價低廉的懸架系統，能大大降低整車生產的總成本，推動汽車經濟的發展。所以本題設計一款結構優良的礦用越野車懸架系統具有一定的實際意義。 二、設計（論文）內容、技術要求（研究方法） （一）設計內容 本設計參考車型為SMV礦用越野車的技術參數，參數如下 總長x總寬x總高(mm) 5500x1800x2100 軸距(mm) 3300 整車整備質量(kg) 4700 滿載質量(kg) 7800 空載前橋軸荷(kg) 2320 滿載前橋軸荷(kg) 2380 空載后橋軸荷(kg) 2380 滿載后拼軸荷(kg) 5420 前簧中心距(mm) 770 前輪距(mm) 1575 后簧中心距(mm) 1000 后輪距(mm) 1575 最高車速(km／h) ≤50 滿載質心高(mm) 1000 確定懸架總體結構，彈性元件設計，導向機構設計，減振器結構設計，主要參數的確定,對主要參數進行強度校核，驗證設計的合理性。 （二）研究方法 1、 參考相關資料，對比各種懸架優缺點，初步確定設計方案。 2、 實地考察相關類型的車，為最終設計方案提供依據。 3、利用Autocad軟件建立礦用越野車懸架二維圖紙。 三、設計（論文）完成后應提交的成果 （一）計算說明部分 完成設計說明書1.5萬字。其中包括懸架總體結構設計，尺寸設計，強度校和部分。 （二）圖紙部分 前后懸架總裝配圖及零件圖一套。 四、設計（論文）進度安排 （1）調研、查閱相關資料、完成開題報告 第1～2周（2月28日～3月13日） （2）確定總體方案 第3～4周（3月14日～3月27日） （3）前懸架設計 第5周 （3月28日～3月3日） （4）后懸架設計 第6周（3月4日～4月10日） （5）零件參數設計 第7～8周（4月11日～4月24日） （6）懸架主要零件強度校核 第9～10周（4月25日～ 5月15日） （7）書寫設計說明書第11～13周（5月16日～5月29日） （8）設計審核、修改設計說明書第14～16周（5月31日～6月19日） （9）畢業設計答辯準備及答辯 第17周（6月20日～6月26日） 五、主要參考資料 [1]龔曙光.ANSYS在應力分析設計中的應用.CAD/CAM計算機輔助設計與制造.2001,(7):70-80 [2]工程中的有限元方法(第3版)．機械工業出版社，2004 [3]黃天澤，黃金陵．汽車車身結構與設計．機械工業出版社，2000 [4]孫桓主編.機械設計.機械工業出版社出版 [5]余志生． 汽車理論[M]，機械工業出版社，1987 [6]陳家瑞主編.汽車構造.人民交通出版社出版 [7]吳鎮著.理論力學.上海:上海交通大學出版社,1997 [8]呂慧瑛.機械設計基礎.北京:清華大學出版社,2002 六、備注 指導教師簽字： 年 月 日 教研室主任簽字： 年 月 日 本科學生畢業設計 礦用越野車懸架系統的設計 系部名稱： 汽車與交通工程學院 專業班級： 車輛工程B07-2班 學生姓名： 王萌 指導教師： 王永梅 職 稱： 講 師 黑 龍 江 工 程 學 院 二○一一年六月 The Graduation Design for Bachelor's Degree Mine off-road Vehicle Suspension System Design Candidate：WangMeng Specialty：Vehicle Engineering Class： B07-2 Supervisor：Lecturer. Wang Yongmei Heilongjiang Institute of Technology 2011-06·Harbin