現場車削提升機制動盤裝置以及工藝設計,現場車削提升機制動盤裝置以及工藝設計,現場,車削,提升,晉升,機制,裝置,以及,工藝,設計 河南理工大學萬方科技學院 本科畢業設計（論文）中期檢查表 指導教師： 牛振華 職稱： 講師 所在院（系）： 機械與動力工程系 教研室（研究室）： 題 目 現場車削提升機制動盤裝置以及工藝 學生姓名 梁利彎 專業班級 08機設2班 學號 0828200015 1、 選題質量： 1、選題符合專業培養目標，充分利用了機械設計方面的知識，并且綜合訓練了大學四年學習的專業知識，再次鞏固加深了大學所學到的知識，為以后在工作實踐當中利用所學知識解決問題打下了堅實的基礎; 2、題目的難度適宜，主要利用刀具的現場加工對已工作的制動盤進行切削校正在加工; 3、題目的工作量較大，在設計的過程中要充分了解工種道具的基本性能，重點是對現場車削制動盤刀架的設計，同時需要計算臨時驅動機構的減速比等等; 4、題目與我們?nèi)蘸蟮墓ぷ鲗嵺`緊密相連，讓我們在機械產品設計方面得到了鍛煉。 二、開題報告完成情況： 開題報告已完成。 3、 階段性成果： 1、初步構思，形成提綱; 2、已搜集大量資料，形成基本設計思路; 3、已經對設計思路進行初步的整理和完善。 4、 存在主要問題： 1、論文的層次有些亂，需要進行調整; 2、論文的語言口語化; 3、論文各部分的銜接性不夠; 4、還不能對專業用語進行靈活地運用。 五、指導教師對學生在畢業實習中，勞動、學習紀律及畢業設計（論文）進展等方面的評語 指導教師： （簽名） 年 月 日 2 河南理工大學萬方科技學院 本科畢業設計（論文）開題報告 題目名稱 現場車削提升機制動盤裝置以及工藝 學生姓名 梁利彎 專業班級 08機設-2班 學號 0828200015 一、 選題的目的和意義： 礦井提升機是煤礦，有色金屬礦生產過程中的重要設備。提升機的安全、可靠、有效高速運行，直接關系到企業的生產狀況和經濟效益。礦井提升系統具有環節多、控制復雜、運行速度快、慣性質量大、運行特性復雜的特點，且工作狀況經常交替轉換。一旦提升機的行程失去控制，沒有按照給及速度曲線運行，就會發生提升機超速、過卷事故，造成楔形罐道、箕斗的損壞，影響礦井正常生產，甚至造成重大人員傷亡，給礦井生產造成重大的經濟損失。 所以提升機調速控制系統的研究一直是社會各界人士共同關注的一個重大課題。提升機的制動系統在很大程度上決定了提升機能否實現平穩、安全、可靠地運行。 盤式制動器：它是近20 年來移植到礦井提升機上的新型制動器，具有慣量小、動作快、靈敏度高、制動力矩可調性好、通用性好、結構簡單、維修調整便等優點，盤式制動器有很多零件是通用的，并且不同的礦井提升機可配不同數量相同型號的盤式制動器。目前大都采用盤式制動器，特別是在多繩磨擦提升機上，幾乎全部采用盤式制動器。 意義： 1. 使專業基礎課程中所獲得的理論知識在實際的設計工作中綜合地加以應用; 2. 能夠掌握設計計算的基本原理和方法,提高設計計算的能力； 3. 夠熟練應用有關參考資料、計算圖表、手冊; 4. 熟悉有關的國家標準和部頒標準; 5. 能夠掌握設計計算的基本原理和方法,提高設計計算的能力. 6. 熟練應用CAD制圖，規范圖紙模板； 樹立正確的設計思想，以便更好的適應以后的工作。 二、 國內外研究綜述： 國內目前運用的較多的是油壓塊式閘制動系統和油壓盤式閘制動系統。盤式制動器是靠碟形彈簧產生制動力， 而靠油壓松閘；制動狀態時，利用碟簧組的彈簧力進行上閘制動。當油壓力降低為零時(上閘過程)，碟簧預緊產生的彈簧力通過碟簧中置推動軸及磨損補償螺柱作用于閘瓦上，施加的正向彈簧力使閘瓦與制動盤貼合產生制動正壓力，從而可以制約制動盤的旋轉趨勢。油缸的壓力容腔充油升壓(松閘過程)，當油液壓力逐步升高至工作壓力時，與閘瓦相連的活塞受油壓作用，克服碟簧的預緊力并壓縮碟簧而產生向后位移，活塞通過中空大螺柱、碟簧中置推動軸、閘瓦磨損補償螺柱而帶動閘瓦后移，閘瓦與制動盤之間形成間隙，從而解除了制動盤上作用的制動正壓力。 三、 畢業設計（論文）所用的主要技術與方法： 1. 檢索大量相關資料，對本課題有一個整體的理解和思路。； 2. 篩選搜集的資料，對本課題的國內外研究動態有一個大致了解，自己形成一個設計大綱。書寫開題報告、文獻綜述和外文翻譯； 3. 根據課題進行工藝計算和結構設計； 4. 固定管板式換熱器的主要部件強度計算、設計以及附件結構的選擇； 5. 繪制設計圖、裝配總圖和部件圖； 6. 書寫畢業論文。 四、 主要參考文獻與資料獲得情況： [1] 潘英．礦山提升機機械設計[M]．徐州：中國礦業大學出版社，2001 [2] 許福玲，陳曉明．液壓與氣壓傳動[M]．北京：機械工業出版社，2004 [3] 方慎權．煤礦機械[J]．徐州：中國礦業大學出版社，1986 [4] 馬天平，張子哲，倪華英，李利芳．液壓盤式制動器的性能特點及應用[J]．太原重型機械集團．冶金設備．2002年12月第6期 [5] 孫素娟．提升機盤形閘現狀及碟形彈簧試驗分析.唐山洞北能源職業技術學院[J]．煤炭技術．2006年6月，第25卷第6期 [6] 成大先，姬奎生．機械設計手冊[M]．北京:化學工業出版社，2002 [7] 麻健,李勇忠．提升機新型液壓制動系統[M]．煤礦機械，1999 五、 畢業設計（論文）進度安排（按周說明） 第1～5周 畢業實習，完成實習報告，收集資料，完成開題報告。 第6～10周 總體方案設計，初步完成設計計算，外文翻譯。 第11～13周 完成總裝圖和零件圖的繪制和設計說明書。 第14～15周 修改和完善，準備畢業答辯。 六、 指導教師審批意見： 指導教師： （簽名） 年 月 日 3 河南理工大學萬方科技學院本科畢業論文 本科畢業設計（論文） 中英文對照翻譯 院（系部） 萬方科技學院機械與動力工程系 專業名稱 機械設計制造及其自動化 年級班級　 機設08-2班 學生姓名 梁 利 彎 指導老師 牛 振 華 2012年5月 ENGINE MECHANICAL Operation Main Components and Classification of the Engine The automotive engine is essentially a heat mobiles are internal combustion engines. Princiole of Operation The spark-ignition engine is an internal-combustion engine with externally supplied in ignition .The gasoline engine is a kind of spark-ignition engines. The four-stroke-cycle gasoline engine cycle is spread over four pistion strokes. The first stroke in your engine is called the intake stroke. Instead of opening the intake valve after you have drawn the poston down . you will find it better to open the intake valve as the piston starts down . This allows the air to draw fuel in the entire time the piston is moving down. Remember , the intake stroke starts with the piston at the top of the cylinder(intake valve open and exhaust valve closed)and stops with the piston at the bottom of its travel . This requires one half turn of the crankshaft. As the crankshaft continues to move , the piston is forced up through the cylinder . If you keep both valves closed , the fuel mixture will be squeezed , or compressed , as the piston reaches the top .This is called the compression stroke . It , too , requires a half turn of the crankshaft . The compression stroke serves to break up the fule into even smaller particles . This happens due to the the sudden swelling and churning of the mixture as it is compressed . When the air fule mixture is subjected to a sudden sharp compression force . its temperature rises .This increase in temperature makes the mixture easier to ignite and causes it to explode with greater force , As the piston reaches the top of its travel on the compression sroke , it has returned to the pro[er position to be pushed back down by the explosion. Remember , the compression stroke starts with the piston at the bottom of the cylinder(both valves closed)and the stops with the piston at the top of the cylinder . This requires an additional half turn of crankshaft . As the piston reaches the top the compression stroke ,the mixture is broken into tiny particles and heated up . when ignited , it will explode with great force . This is the right time to explode the mixture . A spark plug provides a spark inside the combustion chamber ,The spark produced at the plug is formed by the ignition system. Just imagine that a hot spark has been provided in the fuel mixture . The mixture will explode and , in turn , force the piston down into the cylinder . This gives the crankshaft a quick and forceful push . This is the power stroke , Both valves must be kept closed during the power stroke or the pressure of the burning fuel will squirt out through the valve ports . Remenber , the power storke starts with the piston at the top of ylinder(both valves closed) and stops with the piston at the botton of the cylinder , T his requires another half turn of the crankshaft . When the piston reaches the bottom of the power stroke .the exhaust valve opens . The spinning crankshaft forces the piston up through the cylinder , pushing burned gases out . This is the exhaust stroke . Remenber , the exhaust stroke starts with the piston at the bottom of the cylinder (exhaust valve open and intake valve closed) . It stops with the piston at the top of the cylinder . This requires one more half turn of the crankshaft . If you count the number of half turns in the intake , compression , power , and exhaust storkes , You will find you have a total of four , This gives you two complete turns , or revolutions ,of the crankshaft . When the crankshaft is turning around twice ,it is receiving power only during one half turn , or one fourth of the time . As soon as the piston reaches the top of the exhaust stroke , it starts down on another intake , compression , power ,and exhaust cycle , this cycle is repeated over and over ,Each complete cycle consists of four strokes of the piston , hence the name four-storke cycle. Main Engine Componennts Engine Block The engine block serves as a rigid metal foundation for all parts of engine . It contains the cylinders and supports the crankshaft and camshaft . In older engines ,the valve seats , ports ,and guides are built into the block ,Accessry unis and the clutch housing are boled to it . Blocks are made of either cast iron or aluninum ,The lighter the block(providing it has sufficient strength), the better ,The modern thin-wall casting proces controls core size and placement much more accuratcely than the older casting process .This permits casting the block walls much thinner , reducing the weight of the block .Since the bolck wall thickness is more uniform , block distortion during service less severe . Cylinders The cylinder is a aroud hole formed in the block .It forms a guide guide for the piston and acts as a containner for taking in , compressing ,firing , and the exhausting the air-fuel chareg , Cylinder have been made of both steel and cast iron .Cast iron is by far the most popular. When steel cylinders are desired in an aluminum block, they are installed in the form of cylinder sleeves(round , pipe-like liners ), These sleeves may be eiher cast or pressed into the block ,Some engines use removable cylinder sleeves . When the cylinde becomes won The old sleeves can be pulled out and new sleeves can be pressed in . The sleeves are pressed into oversize cylinder holes ,Cylinder sleeves are widely used in heavy-duty truck and industrial engines ,Sleeves can also be used to be repair a won or cracked cylinder in a cast iron block . Pistons The piston must move down through the cylinder to the cylinder to produce a vacuum to draw a fuel charge into the cylinder . It then travels up in the cylinder and compresses the mixture ,When the mixture is fired , the pressure of the expanding gas is transmitted to the top of piston . This drives the piston back down through the cylinder with great force , transmitting the expanding gas to the crankshaft ,The piston then then travels up through the cylinder and exhaust the burned fuel charge. Pistons are usually made of aluminum . Often ,aluminum piston are tin-plated to allow proper break-in when the engine is stared ,Aluminum pistons can be forged ,but they are more commonly cast .Cast iron is a good material for pistons used m a slow-speed engine .It has excellent wear characteristics and will provide good performance . Connecting Rods As the name implies , connecting rods are used to connect protons to the crankshaft .The upper end of the rod oscillates(swings back and forth), while the lower ,or big end ,bearing rotates(turns). Because there is very little bearing movement in the upper end , the bearing area can be reasonably small . The lower end rotates very fast , and the crankshaft bearing journal turns inside the connecting rod . This rotational speed tends to produce heat and wear .To make the rod wear well, a larger bearing area is required. The upper end of the rod has a hole through it for the piston pin ,The botton of the large end of the connecting red must be removed SO the rod can be installed on the crankshaft journal .The section that is removed is called the connecting rod cap. Connecting rods are normally made of alloy steel .They are drop-forged shape and then machined . Crankshaft The engine crankshaft provides a constant turning force to the wheels ,it has through to which connecting rods are attached ,and its function to change the reciprocating motion of the piston to a rotary motion to drive the wheels . Crankshaft are made of alloy steel or cast iron. The crankshaft is held in position by a series of main bearings ,The maximum mumber of main bearings for a crankshaft is one more than the munber of cylinders. It may have fewer main bearings than cylinder .Most engines use pressman insert bearings that are constructed like the connecting rod bearings, But are somewhat larger .In addition to supporting the crankshaft , one of the main bearings must control the forward and backward movement. Flywheel A heavy flywheel is attached to the rear of the crankshaft with bolts ,The function of the flywheel is to smooth out engine speed and keep the crankshaft spinning between power strokes . in some engines , the flywheel also serves as a mounting ,surface for the clutch . The outer rim of the flywheel has a large ring attached with gear teeth cut into it , The teeth of the starter motor engine these teeth and spin the flywheel to crank the engine . When all automatic transmission is used ,the torque converter assembly works with the flywheel. Camshaft The camshaft is used to open and close the valves . There is one cam on the camshaft for each valve in the engine ,Generally only one camshaft is used in most engines . Newer engines are increasingly equipped with two or more camshaft. Valves Each engine cylinder ordinarily has two valves . However , modern engines often use four valves per cylinder(two intake and two exhaust), A few engines used in smaller vehicles have three intake valves per cylinder : two intake valves and one exhaust valves or three intake valves and two exhaust valves . Because the head of an exhaust valve operates at temperatures up to 1300C(704C) ,valves are made of heat-resistant metal . In order to prevent burning ,the valve must give off heat to the valve seat and to the valve guide . The valve must be make good contact with seat and must run with minimum clearance in the guide . Valve Lifters Mechanical valve lifters are usually made of cast iron , The bottom Dart that contacts the camshaft is hardened .Some lifters are hollow to reduce weight .Most valve trains that contain mechanical lifters have some provision for adjusting clearance . Mechanical valve lifters were used in older engines . Hydraulic valve lifters perform the same job as mechanical lifters , However ,hydraulic lifters are self-adjusting , operate with no lifte-to –rocker arm clearance . and uses engine oil under pressure to operate ,Hydraulic lifters are quite in operration . Engine Classification Cycle Classification Engines are often classified according to cycle . Most internal combustion piston engines use a two-or four –stroke cycle .All modern automobile engines use the four stroke cycle engine . The two-stroke cycle engine performs the intake , compression , firing , and exhaust sequence in one revolution of the crankshaft. Cylinder Classification The inline engine has its cylinders arranged one after the other in a straight line , They are in a vertical , or near vertical position . Most modern inline engines are four cylinders . A V-type engine places two banks or rows of cylinders at an angle to each other-genre-ally at 60or 90 ,The V-type engine has several advantages: short length , extra block rigidity , a short , heavy crankshaft , and low profile that is conducive to low hood lines , The shorter block permits a reduction in vehicle length with riot sacrifice in passenger room . The horizontal opposed engine is like a V-type engine , except that both banks lie in a horizontal plane . The advantage here is all extrmely low overall height .Which makes this engine ideally suited installations where space is limited . Cooling Classification As you have learned ,engines are either liquid-collde or air-colled . Most vehicles use liquid-colled engines .Air-colled engines are used in limited numbers modern vehicles . Fuel Classification Automobile engines can use gasoline , diesel fule , gasohol(mixture of gasoline and alcohol), alcohol , LNG(liquefied natural gas) ,CNG(compressed natural gas) ,or LPG(liquefied propane gas ) .Gasoline powers the majority of vehicles , but diesel fule is used in some vehicles .Gosohol ,LNG ,CNG ,and LPG are beginning to see wider use .One of the principle differences in these engines is in method of fuel delivery and carburction .Gasoline ,LNG ,CNG ,and LPG utilize the same basic type of engine , but LNG ,CNG ,and LPG utilize a slightly different fule delivery setup .Diesel engines do not use a carburetor or all ignition system . Valve System Operation of Valve system You have seen that the intake valve stroke .Both valves must remain closed during the compression and power stroke ,and the eshaust valve opens during the exhaust stroke , The designer must design a device to open and close the valves at the proper times . The shaft will have an egg-shaped bump called a cam lobe .The cam lobe is machined as an integral part of the shaft .This shaft is called a camshaft . The distance the valve will be raised , how long it will stay open , and how fast it opens and closes can all be controlled by the height and shape of the hole . As you will see later , it is impractical to have the cam lobe contact the end of valve stem . When the camshaft is turn ,the lobes will not even touch the valve stem ,The lifter is installed between the cam lobe and the valve stem . The upper end rides on the lobe and the lower and almost touches the valve stem . The lifter slides up and down in a a hole bored in the head metal that separates the valve stem from the camshaft . You have developed a method of opening and closing the valves .The next problem is how and at what speed to turn the camshafts , Each valve must be open for one storke .The intake valve is open during the intake storke and remains closed during the compression ,power ,and exhaust stroke .This would indicate that the cam lobe must be turn fast enough to raise the valve erery fourth stroke . You can see that it takes one complete revolution of the cam lobe four strokes of the piston . Remember that four srokes of the piston require two revolutions of the crankshaft , the cam shaft must be once , If you are speaking of the speed of the camshaft ,you can say that the camshaft must turn at one-half crankshaft speed . If the crankshaft is turning and the camshaft must turn at one-half crankshaft speed , it seems logical to use the spinning crankshaft to turn the camshaft ,One very simple way to drive the camshaft would be by means of gears and a belt . One gear is fastened on the end of the crankshaft ,and the other is fastened on the end of the camshaft .The large camshaft gear drives the smaller crankshaft gear through the belt . If ,for instance ,the small gear Oil the crankshaft has 10 teeth and the large gear on the camshaft has 20 teeth ,the crankshaft will truth the camshaft at exactly one-half crankshaft speed . VVT-Toyota`s Continuously Variable Valve Timing The most significant and satisfying changes to the Lexus GS line are in the area power train . In the case of GS300 , Lexus breathes new life into last year`s 3.0Lin-line six by introducing VVT-continuously variable valve timing syestem .On the dyne ,VVT shows up as only five additional horsepower and 10 lb-ft of torque . But in the car it meansfuel economy improvements of 1.6 mpg .smoother idle ,California TLEV (transitional tow-emissions vehicle )certification and zero-to 60 mph a half second quicker . Toyota eliminates the compromise of conventional valve timig with the introduction of VVT , By continuously varying intake valve timing (up to 60 crank angle degrees) , Toyota optimizes low-to mid-speed torque , improves fule economy and lowers emissions without having a negative impact on idle . In essence ,the system controls valve overlap ,which means it can climinate it completyly for a glass smooth idle . or maximize it to boost volumetric efficiency ang reduce pumping losses this translates into power ,economy and cleaner running at all engine speeds. The heart of the system is the intake cam pulley , which consists of an inner and outer section ,The inner portion is fixed to the camshaft and nests inside the belt-driven outer pulley via helical spline gears . An electronically controlled hydraulic piston moves the pully halves relative to one another ,causing the cam portion to rotate within the outer pulley. This rotation davances or retarda intake valve timing .A spool valve reacting to signals from the ECU controls hydraulic pressure . VTEC-Honda Variable Valve Timing and Lift Electronic Control By desiging a higher valve lift ,wider valve-timing ,and large valve valve diameter ,it is possible to obtain a higher volumetric efficienvy to copy with higer output engine speeds ,The VTEC is used to improve volumetric effiency from low engine speed to high engine speed .With VTEC, the valve timing and lift can be dajusted at low engine rotation to increase troque and prevent air from being forced back through the intake . VTEC Operation Fig.2-4 shows the VTEC mechanism while operating at low engine speeds . In the low-speed mode the 3 rocker arms are separated and use cams A&B only . At this time the mid rocker arm is in contact with the high speed cam due to the spring force in the lost motion mechanism .It is separated from the primary and secondary rocker arm and thus is not actuating the valve .Fig.2-5shows the VTEC mechanism while operating in the high speed mode . During high speed engine operation the 3 rocker arms are connected and move together due to the 2 hydraulic pistons which have moved over due to increased hydraulic presure. MIVEC-Mitsubishi Innovative Valve timing Elecctronnic Control system The MIVEC dual-intake valve canshaft enables changing betweeen low-speed and high-speed moders(Fig.2-6), resulting in easy operation from low to high rams ,improving the driving experience when staring from a stop light , merging on to the freeway ,or accelerating to overtake another car .In the pursuit of pure driving enjoyment,potentially incompatible goals like fuel economy ,environment-friendiness,and clean driving have all been achieved . Low-speed Mode The difference in the dual-intake valve lift(low lift and medium lift)and enhanced in-cylinder streaming further stabilize combustion without compromising fuel econmy ,emissions ,and torque . High-speed Mode Extending the injection valve opening time and expanding the valve lift range in ,creases intake air mass and achieves output close to best in class . The Grandis is equipped with the 2.4L MIVEC and the Colt is equipped with the 1.3 and 1.5L MIVEC . Electronic Valve Control System An electronic valve control (EVC) system replace the mechanical camshaft ,controling each valve with actuators for inpendent valve with actuators for independent valve timing .The EVC system control the opening and closing time and lift amout of each intake and exhaust valve with independent actuators on each valve .Changing from a mechanical camshaft driven valve into dependently controled actuator valves provide a huge amount of flexibility in engine control strategy .Vehicles utilizing EVC can realize several benefits including : 1) increase engine power and fuel economy. 2) Allows centralized and distributed EVC system to perform at their full potential. 3) Adapts to engines of varied cylinder counts . With all of improved efficiencies and consumer benefi