干冰清洗機——行走系統,干冰,清洗,行走,系統 ANYANG INSTITUTE OF TECHNOLOGY 畢 業 設 計 說 明 書 干冰清洗機 The washing and spraying type machine for vegetable 系（院）名稱： 機械工程系 專業班級： 06機械設計與制造及其自動化14班 學生姓名： 張 志 勇 指導教師姓名： 梁 博 指導教師職稱： 講 師 2008年 5 月 干冰清洗機的行走系統 專業班級：06機制14班 學生姓名：張志勇 指導教師：梁 博 職 稱： 講 師 摘 要 本設計論述了研制自動化連續型干冰清洗機的必要性和可行性。干冰可以分為葉狀類干冰和根莖類干冰，葉類干冰表面殘存有塵土、有機肥、及殘存的化學農藥、微生物等，且葉類干冰本身比較嫩脆，容易折段壓潰，而根莖類干冰表皮強度較好，有的還要求去皮食用，不存在表皮損傷問題。我們針對葉狀類類干冰和根莖類類干冰這兩種干冰物理性質的不同，分別設計了QX-J型根莖類干冰清洗機和QX-Y型葉狀類干冰清洗機，并介紹了其工藝流程和整體結構。QXJ型根莖類干冰清洗機采用滾筒方式清洗，QX-Y型葉狀類干冰清洗機的工藝流程為浸泡清洗 -- 噴射清洗 -- 超聲波清洗 -- 噴淋清洗 -- 出菜。 利用高于20KHZ的超音頻電能的超聲波，能通過換能器轉換成高頻機械振蕩而傳入到清洗液中。超聲波在清洗液中疏密地向前輻射，使液體移動，并產生數萬計的微小氣泡，這些氣泡在超聲波縱向傳播的負壓區形成、生產、迅速閉合稱為空化現象。在空化現象中氣泡閉合時形成超過1000個大氣壓的瞬時高壓，連續不斷產生的瞬時高壓就像一連串小爆炸不斷地轟擊物體表面，使物體表面及縫隙中污垢迅速剝落，這種空化侵蝕作用就是超聲波清洗的基本原理。 關鍵詞： 自動化 浸泡 噴淋 超聲波清洗 水處理 The washing and spraying type machine for vegetable Abstract This design expounds the necessity and feasibilities to develop the automation continuous type wash, vegetables are divided into leaf form type vegetables and rhizome type vegetable. The surface of the leaf type vegetables and rhizome type vegetable. The surface of the leaf type vegetables remains to have dust, orangic fat. Chomical agriculture chemical and microorganism. And it is fresh and flat, getting easy to be rolled over .The epidermis of the rhizomes type vegetables intensity better. More of them require to unskin eating. So it does not exist the epidermis problem of damaging, we directed against the differences of physical properties of leaf form type vegetables and rhizome type vegetables to design model QX-J wash for leaf form type vegetables and QX-Y for rhizome type vegetables and introduces their technological process and whole structure. Model QX-J rhizome type vegetables wash machine adopt cylinder. And the processes of the Model QX-Y leaf form type wash machine is immersion washing—spray washing—ultrasonic wave washing—spray washing—bringing the vegetables out. The height frequently effect ultrasonies which are more than 20 KHZ are translates the mechanical vibrational via the exchanged energy organ and transmitted into the intermedium.Nonstopped vibration of ultrasonic made the liquid moved forward in the intermedium and can give birth to ten thousands of little air bubble. It is called for around-the-clock that the air bubbles form, develop and shut up rapidly in the pressure region of the track of the ultrasonic moving. The opening of the air bubbles form one thousand of air pressure. The lash of the surface of cleaned object continuous and continuous which likes giving birth to dense explosion on the surface of cleaned object made the grease stain fabled off. The fun dametal is the theory of ultrasonic cleaning. Keywords automize soak gush out and drench ultrasonic washing water treatment 2 安陽工學院本科生畢業設計（論文）課題申報、審核表 系（院）： 機械工程系 填寫時間： 2007 年 12 月 10 日 課題情況 課題名稱 干冰清洗機的行走系統 申報者姓名 梁博 職稱 講師 學位 碩士 課題來源 A.國家、部、省、市科研項目 B.企、事業單位委托 C.自擬課題 D.其它 課題類型 A. 工程設計 B.技術開發與應用 C. 論文 D.其它 難易程度 較難□ 一般□ 較易□ 預計工作量 較大□ 適中□ 較小□ 適合專業 適做人數 課題簡介 該設計是用于干冰、果品清洗機器，我們?cè)O(shè)計的干冰清洗機能夠?qū)崿F(xiàn)自動化連續清洗干冰，除了采用了傳統的浸泡、干冰清洗方式外，還采用國際流行的超聲波凈洗法。它利用液體中聲的空化作用產生微沖流，微沖流在運動過程中小氣泡不斷爆炸，對被清洗干冰表面進行高頻振蕩和沖擊，徹底剝落殘留在干冰、水果表面上的農藥，并能殺滅殘留在其表面的細菌，既不破壞營養，還增加保鮮時間。干冰清洗機的工藝流程為浸泡清洗 -- 噴射清洗 -- 超聲波清洗 -- 干冰清洗 -- 出菜。 目標要求和應具備的基本條件 初步設計由自動進料、自動出料、中間傳送裝置和噴水及其循環利用裝置組成。形成流水線清洗，由水泵出來的水從上下噴頭噴出對在傳送帶上運動的干冰進行清洗。 并完成干冰前預處理、干冰的傳送問題、干冰中殘余農藥的洗怎樣出去。 清洗機的設備裝置為：1、設備組成：根據操作要求分為三個過程：2、浸泡、清洗、瀝干（烘干）；3結構分析：清洗段采用高壓空氣攪拌、高壓水噴射清洗、干冰漂洗及超聲波清洗等；4、各單元應設置物料輸送機構，應考慮各單元之間的聯接；5、清洗廢水的處理，可考慮采用過濾和旋液分離等方式，使清洗廢水可重復利用。 教研室審題意見 主任簽字: 年 月 日 系（院）審題意見 主任（院長）簽字: 年 月 日 備注：本表每題一份，經審核通過的題目方可向?qū)W生公布并選擇，本表系（院）存檔。 畢業設計外文參考文獻翻譯 機械工程 系 2008屆 題 目 干冰清洗機 The washing and spraying type machine for vegetable 學生姓名 張志勇 專業班級 06機制14班 完成日期： 2008 年 3 月 22 日 Contents 1. Abstract ………………………………………………………………………………2 2..ltrasonicCleaning ………………………………………………………………………………2 3. Machining………………………………………………………………………………5 目 錄 1. 摘要……………………………………………………………………………………7 2. 超聲波清洗……………………………………………………………………………9 3. 機械加工………………………………………………………………………………10 Abstract At modern social people the improvements of living standardses, and foreign trade the developments of cause, vegetables process day by day demand increase products day by day, This ask we want and break artificial to wash dish way a traditional one, realize automation and continuity who vegetables wash is by saving a large amount of manpower, material resources soon, Improve the competitiveness of the products. This text it expounds the fact to be continuous type wash the necessity and feasibilities of machine by vegetables to develop automation. Vegetables divide into leaf form type vegetables and rhizome type vegetables, remaining to have dust, organic fat, and remaining chemical agriculture chemical, microorganism,etc.ses surface vegetables type leaf,forms more for being flat and long and thin, getting easy to roll over because it is routed to press at section, rhizomes the type vegetables epidermis intensity better, require and skin and eat also more somes very, Exist epidermis problem of damaging. We directed against leaf form type kinds of vegetables and rhizome type kinds of vegetables these two a kind of vegetables the differences of physical properties, Design Model QX-J wash and Model QX－Y leaf form type vegetables washing machine, introduce its technological process and whole structure by rhizome type vegetables separately. Model QX－J rhizome type vegetables wash machine adopt cylinder, the processes of the Model QX-Y washing machine is immiersion washing -- spray washing -- ultrasonic wave washing -- spray washing -- bringing the vegetable out. ltrasonic Cleaning Fundamental Theory and Application Ultrasonic cleaning machine mainly utilize air impacted effect height frequency and vibrational signal, which ultrasonic vibrational case produce，translate mechanical vibrational and transmit into the intermedium via the exchanged energy organ Ultrasonic fardel,nonstopped vibration produce spoke wise and line transmits ted one. can give birth to ten thousands of negative pressured little air bubble. Via the pressure, the air bubble give birth to dense explosin on the surface of cleaned object. The lash the surface of cleaned object around-the-clock continuous continuous, contain another flank that pene trate the cleaned object. All the inside cavithy,blind holke and narrow interstice, that immerge intermedium,will flake off the greasae stain of the claned object surface. The cleaned object will be perfect and very clean. At the same time, ultra is provided with the liquid purpose. The grease stain that have ever been cleaned will be forfended SANYO Introduces the Worlds First Zero-Detergent Electrolyzed Water Cleaning Powered Washing Machine . Allows the option of "Detergent Course" or "Non-Detergent Course" according to the extent and type of dirt? . Tokyo, June 22, 2001---SANYO Electric Co., Ltd., a world leader in Home Appliances announced the sale of the Worlds first Washing Machine using Electrolyzed Water that does not require the use of detergent through the use of Ultrasonic Waves and Electrolysis. Up until now the industry standard and excepted norm of traditional washing machines worked on the principle of using the water from the washing machine's spin function and soap to remove dirt from the clothing. Three years ago SANYO introduced a new type of washing machine that was different from anything ever seen in the washing machine industry: Dirt Removal through the "Ultrasonic Wave Washing Machine". Lathes Lathes are machine tools designed primarily to do turning, facing, and boring. Very little turning is done on other types of machine tools, and none can do it with equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the workpiece. Consequently, more lathes of various types are used in manufacturing than any other machine tool. The essential components of a lathe are the bed, headstock assembly, tailstock assembly, carriage assembly, and the leadscrew and feed rod. The bed is the backbone of a lathe. It usually is made of well-normalized or aged gray or nodular cast iron and provides a heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shaped for all four ways, whereas others utilize one inverted V and one flat way in one or both sets. They are precision-machined to assure accuracy of alignment. On most modern lathes the ways are surface-hardened to resist wear and abrasion, but precaution should be taken in operating a lathe to assure that the ways are not damaged. Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed. The headstock is mounted in a fixed position on the inner ways, usually at the left end of the bed. It provides a powered means of the rotating the work at various speeds. Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears—similar to a truck transmission—through which the spindle can be rotated at a number of speeds. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical drives. Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through which long bar stock can be fed. The size of this hole is an important dimension of a lathe because it determines the maximum size of bar stock that can be machined when the material must be fed through spindle. The tailstock assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location. An upper casting fits on lower one and can be moved transversely upon it, on some type of keyed ways, to permit aligning the tailstock and headstock spindles. The third major component of the assembly is the tailstock and headstock quill. This is a hollow steel cylinder, usually about 51 to 76 mm (2 to 3 inches) in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a handwheel and screw. The size of a lathe is designated by two dimensions. The first is known as the swing. This is the maximum diameter of work that can be rotated on a lathe. It is approximately twice the distance between the line connecting the lathe centers and the nearest point on the ways. The second size dimension is the maximum distance between centers. The swing thus indicates the maximum workpiece diameter that can be turned in the lathe, while the distance between centers indicates the maximum length of workpiece that can be mounted between centers. Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power drive for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm (12 to 24 inches) swing and from 610 to 1219 mm (24 to 48 inches) center distances, but swings up to 1270 mm (50 inches) and center distances up to 3658 mm (12 feet) are not uncommon. Most have chip pans and a built-in coolant circulating system. Smaller engine lathes—with swings usually not over 330 mm (13 inches)—also are available in bench type, designed for the bed to be mounted on a bench or cabinet. Although engine lathes are versatile and very useful, because of the time required for changing and setting tools and for making measurements on the workpiece, they are not suitable for quality production. Often the actual chip-production time is less than 30% of the total cycle time. In addition, a skilled machinist is required for all the operations, and such persons are costly and often in short supply. However, much of the operator's time is consumed by simple, repetitious adjustments and in watching chips being mad. Consequently, to reduce or eliminate the amount of skilled labor that is required, turret lathes, screw machines, and other types of semiautomatic lathes have been highly developed and are widely used in manufacturing. Machining Turning The engine lathe, one of the oldest metal removal machines, has a number of useful and highly desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered. The engine lathe has been replaced in today's production shops by a wide variety of automatic screw machines. All the advantage of single-point tooling for maximum metal removal, and the use of form tools for finish and accuracy, are now at the designer's fingertips with production speeds on a par with the fastest processing equipment on the scene today. Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the engine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used. . Milling With the exceptions of turning and drilling, milling is undoubtedly the most widely method of removing metal. Well suited and readily adapted to the economical production of any quantity of parts, the almost unlimited versatility of the milling process merits the attention and consideration of designers seriously concerned with the manufacture of their product. As in any other process, parts that have to be milled should be designed with economical tolerances that can be achieved in production milling. If the part is designed with tolerances finer than necessary, additional operations will have to be added to achieve these tolerances—and this will increase the cost of the part. Grinding Grinding is one of the most widely used methods of finishing parts to extremely close tolerances and fine surface finishes. Currently, there are grinders for almost every type of grinding operation. Particular: cylindrical grinders, centerless grinders, internal grinders, surface grinders, and tool and cutter grinders. The cylindrical and centerless grinders are for straight cylindrical or taper work; thus splines, shafts, and similar parts are ground on cylindrical machinesdesign features of a part dictate to a large degree the type of grinding machine required. Where processing costs are excessive, parts redesigned to utilize a less expensive, higher output grinding method may be well worthwhile. For example, wherever possible the production economy of centerless grinding should be taken advantage of by proper design consideration. Although grinding is usually considered a finishing operation, it is often employed as a complete machining process on work which can be ground down from rough condition without being turned or otherwise machined. Thus many types of forgings and other parts are finished completely with the grinding wheel at appreciable savings of time and expense. Classes of grinding machines include the following either of the common-center type or the centerless machine. Thread grinders are used for grinding precision threads for thread gages, and threads on precision parts where the concentricity between the diameter of the shaft and the pitch diameter of the thread must be held to close tolerances. The internal grinders are used for grinding of precision holes, cylinder bores, and similar operations where bores of all kinds are to be finished. The surface grinders are for finishing all kinds of flat work, or work with plain surfaces which may be operated upon either by the edge of a wheel or by the face of a grinding wheel. These machines may have reciprocating or rotating tables 摘 要 隨著現代社會人們生活水平的提高，以及外貿事業的發展，干冰加工產品的日益需求量日益增大，這就要求我們要打破傳統的人工洗菜方式，實現干冰清洗的機械化和自動化，以節省大量的人力、物力，提高產品競爭力。 本文論述了研制自動化連續型干冰清洗機的必要性和可行性。干冰可以分為葉狀類干冰和根莖類干冰，葉類干冰表面殘存有塵土、有機肥、及殘存的化學農藥、微生物等，且葉類干冰本身比較嫩脆，容易折段壓潰，而根莖類干冰表皮強度較好，有的還要求去皮食用，不存在表皮損傷問題。我們針對葉狀類類干冰和根莖類類干冰這兩種干冰物理性質的不同，分別設計了QX-J型根莖類干冰清洗機和QX-Y型葉狀類干冰清洗機，并介紹了其工藝流程和整體結構。QXJ型根莖類干冰清洗機采用滾筒方式清洗，QX-Y型葉狀類干冰清洗機的工藝流程為浸泡清洗 -- 噴射清洗 -- 超聲波清洗 -- 噴淋清洗 -- 出菜。 關鍵詞 設備 性能 自動化 浸泡 噴淋 超聲波清洗 水處理 超聲波清洗：基本原理及應用 利用高于20KHZ的超音頻電能，通過換能器轉換成高頻機械振蕩而傳入到清洗液中。超聲波在清洗液中疏密地向前輻射，使液體移動，并產生數萬計的微小氣泡，這些氣泡在超聲波縱向傳播的負壓區形成、生產、迅速閉合稱為空化現象。在空化現象中氣泡閉合時形成超過1000個大氣壓的瞬時高壓，連續不斷產生的瞬時高壓就像一連串小爆炸不斷地轟擊物體表面，使物體表面及縫隙中污垢迅速剝落，這種空化侵蝕作用就是超聲波清洗的基本原理。 SANYO 首先介紹世界沒有洗滌劑，將電解水作為動力的洗衣機，根據范圍和灰塵的類型可以選擇用洗滌濟或不用洗滌濟進行清洗。 SANYO 電氣股份有限公司－－世界在家庭用具的領導人于2001 年6月22 日在東京宣布首先使用超聲波和電解水而不需要洗滌濟的洗衣機出售。 直到現在，工業標準和傳統習慣都是利用水在洗衣機里的旋轉運動，肥皂可從衣服上除去灰塵和污垢。3年以前SANYO提出了不同于任何過去的清洗機的的一種洗衣機： 超聲波清洗機。 車床 車床主要是為了進行車外圓、車斷面和鏜孔等工作而設計的機床。很少有車削在其他類型機床上進行，任何機床都不如車床用來車削那樣方便。因?yàn)檐?chē)床還能夠用于鉆孔和鉸孔，他們的多功能性允許工件再一次裝夾中完成幾種加工。因此，在生產加工中各種車床的使用比其他機床要多。 車床的基本部件有：床身、主軸箱組件、尾架組件、拖板組件、絲杠和光杠。 床身是車床的支架。它通常是由經過良好正火或失效處理的灰鑄鐵或球墨鑄鐵制成。床身提供了堅固的剛性框架，所有其他基本部件都安裝在床身上。通常在床身上部有內外兩組縱向排列的平行導軌。一些生產廠家對四條導軌都采用導軌頂尖朝上的方式（三角形導軌），而另一些制造廠對一組或兩組導軌都采用一個三角形導軌和一個平行導軌。導軌需要精加工以保證其直線度精度。為了抵抗磨損和擦傷，大多數現代化機床都是經過表面淬硬的。但是在機械加工時還得謹慎小心以免導軌遭到破壞，導軌的任何不精確度常常意味著整臺機床的精度遭到破壞。 主軸箱安裝在內側導軌的固定位置上， 通常在床身的邊端。 它提供動力以使工件在不同速度下旋轉。主軸箱基本上由安裝在精密軸承中的空心主軸和一系列變速齒輪—— 類似于卡車變速箱——所組成。通過變速齒輪主軸，可以在很多轉速下旋轉。大多數車窗提供8支8種轉速，轉速通常按等比級數排列。而且在現代機床上全部轉速都可通過扳動到2到4個手柄得到。一種不斷漸增的趨勢是通過電的或機械的裝置提供無級變速。 由于機床的精度在很大程度上取決于主軸，因此，主軸具有較大的結構尺寸，通常安裝在預緊后的重型圓錐滾子軸承或球軸承中。主軸上有一個貫穿全長的通孔，通過該孔長棒料可以進料。這個孔的大小是車床上一個非常重要的尺寸，因?yàn)楫?dāng)原材料必須通過主軸孔供料時，它決定了能夠被加工的棒料毛坯的最大尺寸。 尾架組件基本上包括三個部分。底板和床身內側導軌配合，并且能夠在導軌上縱向滑動。底板上有一個可使整個尾架組件在任意位置上夾緊的裝置。尾架體安裝在底板上，可以沿某種類型的鍵槽在底板上橫向移動，使尾架能與主軸箱中的主軸對正。尾架的第三個部分是尾架套筒。它是一個中空的圓柱體，直徑通常約為51至76毫米（2到3英尺）。通過手輪和螺桿，尾架套筒可以在尾架體中移入和移出幾寸。 車床的規格用兩個尺寸來表示。第一個稱為最大加工直徑。這是在車床上能過旋轉的工件的最大直徑，它大約是車床中心連線與導軌上最近點連線距離的2倍。第二個規格是兩頂尖之間的最大距離。車床床面上最大加工直徑表示在車床能車削的工件最大直徑，而兩頂尖之間的最大距離則表示在兩頂尖之間能夠安裝的工件的最大長度。 普通車床是生產加工中最常用的車床類型。它們是具有前面所描述的所有部件的重載機床，并且除了復合支架以外，所有的刀具運動都有機驅動。它們通常的規格尺寸是：床面上最大加工直徑為305至610毫米（12至4英寸），兩頂尖之間的距離為610至219毫米（24至48英寸）。但是床面上最大加工直徑大刀270毫米（50英寸），兩頂尖之間的距離達到3658毫米（12英尺）也并不少見。這些車床大部分都有切削盤和一個安裝在內部的冷卻液系統。小的普通車床——床面最大加工直徑通常不超過30毫米（13英寸）——被設計為臺式車床，床身被安裝在工作臺或柜子上。 盡管普通車床的應用多種多樣，且非常有用，但是由于更換和調整刀具以及對工件進行測量要花費很多時間，它們并不適合在大批量生產中應用。通常實際的生產時間總少于全部生產循環時間的30%。另外，需要熟練的技術工人來進行所有操作，而這些技工的工資很高并且常常雇傭不到。然而操作者的大部分時間卻花費在簡單的重復調整和觀察切削的產生上。因此，為了減少或不再雇傭這些熟練工人，六角車床、螺絲車床和其他種類的半自動和自動車床已經被成功地開發出來，并且已經在生產中獲得廣泛應用。 機械加工 車削 普通車床作為最簡單的金屬切削機床中的一種，有許多有用的和為人們所需要的特性。今天這些車床被主要地用于小工廠中，用來進行小批量生產而非大批量生產。 在今天的生產車間中，普通車床已經被各種各樣的自動車床所代替，諸如自動仿形車、六角車床和自動螺絲車床。用單刃刀具去除大部分的金屬余量，然后用成型刀具獲得表面光潔度和精度這種加工方法的優點，現在用在設計人員的手指尖上的生產速度等同于今天工廠中使用的最快的加工設備的速度。 普通車床的加工偏差主要取決于操作者的熟練程度。設計工程師必須認真地確定由一個熟練的操作者在普通車床上生產試驗零件所用的公差。在把試驗零件重新設計為生產零件時，應該選用經濟的公差。 銑削 除了車削和鉆削，銑削無疑是最廣泛應用的金屬切削方法。銑削非常適合于也易于應用在任何數量的零件的批量生產中。銑削過程的幾乎不受限制的多種使用性能，值得設計人員在他們的產品生產中認真考慮和選擇。 正如和其他加工種類一樣，需要銑削的零件應該設計好在銑削加工中可以獲得的經濟公差。如果零件的設計公差比需要的公差小，那么，為了獲得這個較小的公差，就需要增加一些額外的操作——這將會增加工件的成本。 磨削 磨削是廣泛使用的零件精加工方法之一，用來獲得極小的公差和較好的表面光潔度。目前，幾乎存在適合所有磨削操作的磨床。零件獨特的設計特征在很大程度上決定了需要采用的磨床的種類。當生產成本太高時，就值得對零件進行重新設計，以便采用一種即便宜又具有高生產率的磨削方法進行加工。例如，在有可能的時候，通過對適當?shù)脑O(shè)計方法的考慮，采用無心磨削的方法可以獲得好的經濟效益。 盡管磨削經常被認為是精加工工序，對于那些采用磨削進行粗、精加工的工件，常常用磨削的方法完成整個加工工作，而不用車削或其他加工方法。因而許多種類的鍛件和其他零件的加工都是完全采用砂輪磨削的方法完成的，而且節省時間和費用。 磨床包括以下幾種類型：外圓磨床、無心磨床、內圓磨床、平面磨床和工具磨床。 外圓磨床和無心磨床是用來磨削圓柱形工件或圓錐形工件的。因此，花鍵軸、軸和其他類似的零件是采用普通的外圓磨床，或是采用無心磨床進行加工的。 螺紋磨床用來磨削螺紋量規上的精密螺紋，和用來磨削螺紋的中徑與軸的同心度公差很小的精密零件上的螺紋。 內圓磨床用來磨削精密的孔、汽缸孔以及各種各樣類似的、需要進行精加工的孔。 平面磨床用來對各種平面工件，或者對帶有平面的工件進行精加工。這種平面工件可以采用砂輪的邊或砂輪的端面進行磨削。這類機床上裝有往復式工作臺或回轉式工作臺。 課題分析 1 干冰清洗目的 一般數來,對干冰清洗的目的主要有以下兩個： 一、除去干冰原料表面沾染的泥沙、雜質 干冰原料在其生長、成熟、采摘、貯存、運輸過程中,歷經時間長,歷經工序多,不可避免地會沾染泥沙、雜質等異物,特別是來自地下的果實,如土豆、紅薯等,更是不可避免地與泥土相粘連.這些泥土、雜質的存在,將會對產品的加工質量帶來極為不利的影響.所以必須將這些泥沙、雜質的洗滌除去. 二、去原料表面沾染的農藥和微生物 干冰原料在生長過程中,為了控制病蟲害,常常對干冰要噴射一些農藥,這些農藥的存在會有損于人體健康.另外,干冰表面也會或多或少地沾染各種微生物,這些微生物有可能危害干冰原料和人體健康,因此必須將其除去. 干冰原料清洗目的是去除干冰原料中一切不符合作業要求的物質，尤其是微生物。在清洗前，正常的干冰原料表面上的微生物數量在10000-100000000個/g之間，某些干冰，由于往往粘附著泥土，微生物數量還要高得多。通過正確的清洗工藝，干冰原料的微生物數量會降低到初始數量的2.5-5%左右。 2 清洗工藝及設備設計的要求 在選擇清洗工藝及設備，必須考慮清洗要求達到的洗凈程度。對不同洗凈程度要求的清洗應選擇不同的清洗工藝和設備。洗凈程度要求越高，清洗成本也越高，而且生產成本是以幾何級數遞增的。 在設計清洗工藝及清洗設備時，主要從以下幾個方面進行考慮： 一、可靠性 要求選用的清洗工藝及設備有穩定的清洗質量，能達到所要求的洗凈程度; 二、對待清洗對象的影響 要求在清洗過程中對待清洗對象造成的損傷盡可能小，并且不能對待清洗對象產生新的二次污染; 三、利于自然環境的保護 要求清洗工藝及設備能夠防止或盡可能減少清洗廢液、噪聲、廢氣等對自然環境造成的破壞; 四、效率 要求清洗工藝及設備具有效率高、節約勞動力的特點; 五、良好的作業環境 要求所用的清洗工藝及設備能保持良好的作業環境，使工人的健康和安全得到保證; 六、經濟性 要求采用既能達到洗凈程度要求，成本又低的清洗工藝及要求。 食品加工原料在其成熟階段以及運輸、貯藏過程中常常受塵埃、沙粒及微生物等污染，因此，在加工前必須認真清洗，并清除雜物及不合格部分，以便后道工序加工。 3 常見方案分析 3．1 刷淋式清洗機 刷淋式清洗機通過浸泡、刷洗和噴淋作用能夠有效地提高清洗效果，水槽中的清洗水還能采用蒸氣直接加熱，適用于蘋果、柑桔、梨、番茄等果蔬的清洗。 工作時，物料從進料口進入清洗槽內，在裝有毛刷的刷輥相對向內旋轉作用下，使物料在水的攪動形成的渦動環流中得到清洗，同時由于刷輥之間水流壓力差作用，物料自動向刷輥間流動而被刷洗。刷洗后的物料向上浮起，經翻料斗沿圓弧面移動，受高壓水噴淋沖洗，最后由出料口流出。 3．2 槳葉式清洗機 槳葉式清洗機是通過旋轉的槳葉，攪動浸泡在水中的原料，將物料進行翻滾、摩擦而完成清洗過程，主要適用于質地較堅硬和表面抗損較強的原料。 槳葉式清洗機主要由槽體、槳葉、撈料斗等組成。槽體是一個長方形臥式敞口槽，下部為半圓筒形的空花假底，其下是1-2個漏斗，可收集泥沙雜物。槽體一般用不銹鋼板焊接而成。主軸縱貫槽體，其上按一定間隔安裝有槳葉，相鄰槳葉互相垂直排列，槳葉具有鈍形棱角，可保護原料少受損傷。在槽體末端安有撈料斗，由主軸帶動回轉。 工作時，往槽體中先裝清水，再使主軸旋轉，然后將原料倒入槽體，由于槳葉的轉動，攪動原料，使其翻滾運動，另外，由于槳葉相對于主軸有一定角度，從而推動原料使其向槽體末端移動，在此過程中基本完成了對原料的清洗，至末端由撈料斗撈出，在原料撈出時，清水噴頭噴出清水，完成了對原料的清洗噶過程。而洗下的泥沙雜物則穿過空花假底，聚集于漏斗之中，可定期打開斗底排污閥將其排出機外。 3．4 浸泡式清洗機 浸泡噴洗機是先將原料浸泡于水中，使泥沙雜質在水的浸泡變得松脫，然后受到高壓水流的噴射，使原料表面的附著物沖洗掉而達到清洗的目的。 工作時，先將斜壁水槽中注滿水，再倒入需清洗的原料，經過一定時間浸泡后，開始傳動裝置使輸送帶運轉，輸送帶則帶動原料上行，在噴淋區內高壓水流從噴淋頭直噴向原料，將原料上沾染的泥沙、塵土、雜質沖洗干凈。若原料上沾染了化學試劑，也很容易除去。 浸泡噴洗機結構主要有斜壁水槽、輸送帶、噴淋頭、傳動裝置等組成。輸送帶呈傾斜安裝，與水平面的夾角為25-30度，輸送帶用金屬網制造，以利瀝水，在金屬網上間隔一定距離安裝一根橫條，以便擋住物料下滑。斜壁水槽的斜角與輸送帶的斜角相同，在輸送帶的中部上方裝有多排噴淋頭，輸送帶由傳動裝置帶動運動。 3．5滾筒式清洗機 滾筒式清洗機是借助圓形滾筒的轉動，使原料在其中不斷地翻轉，同時用水管?chē)娚渌鱽?lái)沖洗翻動原料，以達到清洗的目的。該機適合清洗柑橘、橙子、馬鈴薯等根莖類干冰。 滾筒式清洗機的特點是：結構簡單，清洗效率高，工作平穩，不存在力不平衡現象, 對原料的適應性強。 另外由于沿滾筒內壁焊有幾根管子，大大地提高了滾筒的清洗效果。不足之處是整個機械的占地面積大。 針對葉片類干冰的特點, 只有刷淋式清洗機和浸泡式清洗機適合于清洗?，F(xiàn)在針對這兩種方式我們進行對比研究，力爭設計出最佳機構。 12