紅外遙控電路設計論文資料,紅外,遙控,電路設計,論文,資料 天津工程師范學院 學生畢業設計（論文）中期報告 系別 電子系 班級 應電041 學生 姓名 陳春秀 指導 教師 葛穎 課題名稱：紅外遙控發射接收電路設計 簡述開題以來所做的具體工作、取得的進展及下一步主要工作： 1、 開題以來所做的具體工作和取得的進展或成果 在圖書館和網上收集相關資料，學習了單片機理論，在此基礎上，對單片機有了一個整體的認識，基本完成了前面理論部分的學習。經過查閱大量的相關資料，現在已經對紅外遙控的原理有了一個清晰深入的了解，對單片機控制系統及其原理進行了詳細分析，并對單片機的接口電路都進行了詳細的了解。 現在正在完成相關電路的制作及相關程序的編寫，并解決在此過程中所遇到的問題，收集制作過程中的相關資料，為畢業論文的撰寫準備資料。 2、存在的具體問題 在制作過程當中要不斷的對程序進行修改，由于對單片機編程掌握不是很熟練，在實際調試過程中有一定的困難。關于紅外遙控發射機接收電路設計設計資料掌握不全面，因此在實際的電路制作、調試以及相關程序的編寫中存在一定的困難。 3、下一步的主要研究任務，具體設想與安排 繼續電路制作以及相關程序調試，得出結果。制作出實用的由單片機控制的紅外遙控發射機接收電路，即可完成遙控發射通過掃描按鍵，每按下一個鍵，即產生具有不同的編碼數字脈沖，這種代碼指令信號調制在40KHZ的截波上，激勵紅外光二級管產生具有脈沖串的紅外波，通過空間的傳送到受控機的遙控接收器。在接收過程中，紅外波信號通過接收頭轉換為40KHZ的脈沖信號，送到解碼與接口電路，從而完成相應的遙控功能。 根據掌握的畢業設計的相關資料以及在調試過程中所遇問題的解決的相關資料，著手撰寫論文。 學生簽字： 2007年5月18日 指導教師的建議與要求： 指導教師簽字： 2007年5月18日 注：本表格同畢業設計（論文）一同裝訂成冊，由所在單位歸檔保存。 天津工程師范學院 畢業設計（論文）任務書 2006 年 10月 15日 題 目 （包括副標題） 紅外遙控電路設計 教師姓名 葛穎 系 別 電子工程 職 稱 講師 學生姓名 陳春秀 班 級 應電041 學 號 21 課題成果形式 論文█ 設計說明書□ 實物█ 軟件□ 其它□ 1．畢業設計（論文）課題任務的內容和要求（如原始數據、技術要求、工作要求等）： 1、畢業設計主要內容 1．紅外遙控電路設計； 2．2006 年11月9日完成開題報告； 3．畫出標準電路原理圖（電子板），給出測試點電壓或電流； 4．2007年5月10日完成中期報告； 5．制作實際電路（手工焊接），描述硬件電路特性； 6．本專業英語譯文3000字符以上（內容自選、應與畢業設計題目密切相關）； 7．撰寫畢業設計論文（10000字以上）； 8．2007年6月1日提交畢業論文初稿； 9．根據學院的具體要求，完成畢業答辯相關事宜。 2．畢業設計（論文）工作進度計劃： 周 次 工作內容 2006年10月15 日 2006年11月9 日 第一周 第二周 第三周 第四周 第五周 第六周 第七周 第八周 下達畢業設計任務書 開題報告 查閱相關資料，確定設計方案；、 設計電路 設計電路方案確定 提交中期報告、購買電子元器件 焊接電路、軟件編程、調試電路 修改畢業論文、畢業論文預答辯 撰寫畢業論文、提交畢業論文初稿 準備答辯，對設計內容進行總結，弄懂各部分的原理及系統的 工作過程，寫出畢業答辯的發言稿，做到心中有數，應對畢業答辯。 教研室（學科組）主任簽字： 畢業設計（論文）開題報告 題目：紅外遙控電路設計 系 別： 電子工程系 班 級： 應電041班 學生姓名： 陳春秀 指導教師： 葛穎 2006年11月9日  開題報告填寫要求 1．開題報告作為畢業設計答辯委員會對學生答辯資格審查的依據材料之一，應在指導教師指導下，由學生在畢業設計工作前期完成，經指導教師簽署意見、專家組及系主任審查后生效； 2．開題報告必須用黑墨水筆工整書寫或按教務處統一設計的電子文檔標準格式（可從教務處網頁上下載）打印，禁止打印在其它紙上后剪貼； 3．畢業設計的開題報告應包括以下內容： （1）主要技術指標； （2）工作思路； （3）課題的準備情況及進度計劃； （4）參考文獻。 4．開題報告的撰寫應符合科技文獻規范，且不少于2000字；參考文獻應不少于15篇，包括科技期刊、教科書、專著、外文等。 5．開題報告正文字體采用宋體小四號，1.5倍行距。附頁為A4紙型，左邊距3cm，右邊距2cm，上下邊距為2.5cm，字體采用宋體小四號，1.5倍行距。 畢業設計（論文）開題報告 課題題目 紅外遙控電路設計 課題類型 工程設計 課題來源 自擬 成果形式 實作 同組同學 無 開題報告內容（可另附頁） 畢業設計開題報告： （后接附頁） 指導教師意見（課題難度是否適中、工作量是否飽滿、進度安排是否合理、工作條件是否具備等） 指導教師簽名： 月 日 專家組及系里意見（選題是否適宜、各項內容是否達到畢業設計（論文）大綱要求、整改意見等） 專家組成員簽字： 教學主任（簽章）： 月 日 附件：開題報告 紅外遙控電路設計 （一）研究的現狀和發展趨勢 隨著當今世界經濟的快速發展和信息化時代的來臨，各種各樣的電子產品陸續出現在我們的生活中。而我所要設計的紅外遙控發射機就屬其中。紅外遙控廣泛應用于家庭、銀行、證券、郵電、賓館、醫院、學校、企業、商店等相關行業的大廳，以及單位會議室、門衛等場所。在多媒體教學系統的使用、開發和研制中，經常遇到同時使用多種設備，如：數字投影機、DVD、VCD、錄像機、電視機等，由于各種設備都自帶遙控器，而且不同的設備所遵循的紅外傳輸規約也不盡相同，操縱這些設備得使用多種遙控器，給使用者帶來了諸多不便。我想通過這次畢業設計，實做出一個用途這么廣泛的紅外遙控電路。希望在此過程中，通過實踐系統學習51單片機編程，深入了解紅外遙控電路的制作和設計過程等相關知識。 （二）主要任務以及主要技術指標 紅外遙控是目前使用最廣的一種遙控手段。紅外線遙控裝置具有體積小、功耗低、功能強、成本低等特點。在家庭生活中，錄音機、音響設備、空調采電都采用了紅外遙控系統。利用紅外傳輸控制指令，基于和單片機的編程設計，借助單片機強大靈活的控制功能發出脈沖編碼，組成一個遙控系統。 遙控范圍：4—6米 顯示可控制的通道： 接收靈敏可靠，抗干擾能力強 控制用電器（燈具）電流最高為2A 紅外遙控系統由發射和接收兩大部分組成，系統采用編/解碼專用集成電路和單片機芯片來進行控制操作。設計的電路由如下的幾個基本模塊組成：直流穩壓電源，紅外發射電路，紅外接收電路及控制部分。 系統框圖如圖1所示。 按鍵部分 單片機 89C2051 發射部分 電源 3V 圖1 紅外遙控電路框圖 （a）發射電路框圖 5V 接收部分 單片機 89C51 顯示部分 控制部分 電源 9V 圖1 紅外遙控電路框圖 （b）接收電路框圖 （三）研究線路與關鍵技術 紅外遙控的特點是不影響周邊環境的、不干擾其他電器設備。由于其無法穿透墻壁，故不同房間的家用電器可使用通用的遙控器而不會產生相互干擾；編解碼容易，可進行多路遙控。 發射電路，利用遙控發射利用鍵盤，每按下一個鍵，即產生具有不同的編碼數字脈沖，這種代碼指令信號調制在40KHz的載波上，激勵紅外光二極管產生具有脈沖串的紅外波，通過空間的傳送到受控機的遙控接收器。 在接收過程中，紅外波信號通過光學濾波器和光電二極管轉換40KHZ的電信號，此信號經過放大，檢波，整形，解調，送到解碼與接口電路，從而完成相應的遙控功能。 （四）、題的準備情況及進度計劃； 2006年10月15日 2006年11月9 日 第一周 第二周 第三周 第四周 第五周 第六周 第七周 第八周 下達畢業設計任務書 開題報告 查閱相關資料，確定設計方案；、 設計電路 設計電路方案確定 提交中期報告、購買電子元器件 焊接電路、軟件編程、調試電路 修改畢業論文、畢業論文預答辯 撰寫畢業論文、提交畢業論文初稿 準備答辯，對設計內容進行總結，弄懂各部分的原理及系統的 工作過程，寫出畢業答辯的發言稿，做到心中有數，應對畢業答辯。 參考文獻： 1 李振玉，姚光圻.高頻放大及功率合成技術.北京:中國鐵道出版社,1985年,第一版 2 李錦春,蔡仁明.常用晶體二極管、大功率三極管手冊.北京:人民郵電出版社,1981年,第一版 3 康華光,鄒壽彬.電子技術基礎數字部分第四版.北京:高等教育出版社,2000年,第四版 4 康華光,陳大欽.電子技術基礎模擬部分第四版.北京:高等教育出版社,1999年,第四版 5 楊振江,杜鐵軍,李群.流行單片機實用子程序與應用實例.西安:西安電子科技大學出版社,2002年,第一版 6 鈴木憲次.高頻電路設計與制作.北京:科學出版社,2005年,第一版 7 吳金戌,沈慶陽,郭庭吉.8051單片機實踐與應用.北京:清華大學出版社,2002年,第一版 8 李廣弟,朱月秀,王秀山.單片機基礎修訂本.北京:北京航空航天大學出版社,2001年,第二版 9 第二屆全國大學生電子設計競賽組委會.全國大學生電子設計競賽獲獎作品選編(1994-1995).北京:北京理工大學出版社,1997年,第一版 10 全國大學生電子設計競賽組委會.第四屆全國大學生電子設計競賽獲獎作品選編(1999).北京:北京理工大學出版社,2001年,第一版 11 全國大學生電子設計競賽組委會.第五屆全國大學生電子設計競賽獲獎作品選編(2001).北京:北京理工大學出版社,2003年,第一版 12 全國大學生電子設計競賽組委會.全國大學生電子設計競賽獲獎作品選編(2003).北京:北京理工大學出版社,2005年,第一版 13 高吉祥.高頻電子線路學習輔導及習題詳解.北京:電子工業出版社,2005年,第一版 14 謝自美.電子線路設計·實驗·測試(第二版).武漢:華中科技大學出版社,2000年,第二版 15 譚博學,苗匯靜.集成電路原理以應用.北京:電子工業出版社,2003年,第一版 16 黃智偉.全國大學生電子設計競賽訓練教程.北京:電子工業出版社,2005年,第一版 17 劉征宇,韋立華.最新74系列IC特性代換手冊.福建:福建科學技術出版社,2002年,第一版 18 張俊謨.單片機中級教程(原理與應用).北京: 北京航空航天大學出版社,2000年,第一版 19 張肅文.高頻電子線路第四版.北京:高等教育出版社,2004年,第四版 20 黃永定,唐克學.電子實驗綜合實訓教程.北京:機械工業出版社,2004年,第一版 4 Tianjin University of Technology and Education 畢 業 設 計 專 業： 應用電子技術 班級學號： 應電041班 - 21 學生姓名： 陳春秀 指導教師： 葛穎 講師 二〇〇七年 六 月 天津工程師范學院專科生畢業設計(論文) 紅外遙控電路設計 The design of circuit by infrared control 專業班級：應電041班 學生姓名：陳春秀 指導教師：葛穎 講師 系 別：電子工程系 2007 年 6月 摘 要 隨著科學技術的飛速發展，信息的飛快傳播，紅外遙控在人們的生活中已經成為不可或缺的部分。本文重點介紹了利用單片機AT89S52和AT89C2051實現紅外發射和接收電路的設計方法。發射電路通過對單片機89C2051的編程，再通過紅外二極管產生脈沖傳送到接收器上。接收電路通過單片機AT89S52的控制編程，實現對不同設備的控制。整個電路耗電省、簡單可靠、操作靈活、性能價格比高，較好地滿足了現代生活，生產和科研的需要。 關鍵詞：紅外遙控,發射電路,接收電路,單片機 ABSTRACT With the rapid development of technology, the rapid dissemination of information means that infrared control has become an indispensable component in people’s life. The article highlighted the design method of transmitting and receiving circuit by infrared control which use single-chip microcomputer AT89S52 and AT89C2051. After loading the program to the single-chip microcomputer 89C2051, by the transmitting circuit , the infrared diode turns out impulsion then transfer the single to the receiver. Receiving circuit use single-chip microcomputer AT89S52 which can program to control different equipments. The entire circuit is simple, reliable, flexible operation，high-performance, of high value and low cost, and it can meet the modern life, production and research need. Keywords： infrared control,transmitting circuit, receiving circuit,single-chip microcomputer 目 錄 引言…………………………………………………………………………………… 1 1 設計要求及指標……………………………………………………………………… 2 2紅外遙控系統的設計………………………………………………………………… 3 3紅外收發電路的設計…………………………………………………………………4 3.1 主要芯片——閃電存儲型單片機AT89C51的介紹…………………………… 4 3.2 89C2051 介紹…………………………………………………………………… 6 3.3 系統的功能實現方法…………………………………………………………7 3.4 紅外發射電路………………………………………………………………… 9 3.5 紅外接收電路………………………………………………………………… 9 3.6 軟件設計……………………………………………………………………… 10 4直流穩壓電源的設計…………………………………………………………………14 4.1 直流穩壓電源采用單相橋式整流電路…………………………………………14 4.2 濾波電路…………………………………………………………………………15 4.3 穩壓電路…………………………………………………………………………16 5 LED顯示電路的設計…………………………………………………………………17 6控制部分………………………………………………………………………………19 7 調試結果及其分析……………………………………………………………………21 8 結論……………………………………………………………………………………22 參考文獻…………………………………………………………………………………23 附錄1：發射程序………………………………………………………………………24 附錄2：接收程序………………………………………………………………………29 附錄3：紅外發射接收電路總電路圖……………………………………………………33 致謝………………………………………………………………………………………34 英文資料及中文翻譯 Radio Receiver A block diagram for a modern radio receiver is shown in Fig..2-4.The input signals to this radio are amplitude-modulated radio waves. The basic electronic circuits include: antenna ,tuner, mixer, local oscillator ,IF amplifier, audio detector, AF amplifier, loudspeaker, and power supply. Fig.2-4 A Block Diagram For Modern Radio Receiver Any antenna system capable of radiating electrical energy is also able to abstract energy from a passing radio wave. Since every wave passing the receiving antenna. Induces its own voltage in the antenna conductor, it is necessary that the receiving equipment be capable of separating the desired signal from the unwanted signals that are also inducing voltages in the antenna. This separation is made on the basis of the difference in frequency between transmitting stations and is carried out by the use of resonant circuits, which can be made to discriminate very strongly in favor of a particular frequency. It has already been pointed that, by making antenna circuit resonant to a particular frequency, the energy abstracted from radio waves of that frequency will be much greater than the energy from waves of other frequencies; this alone gives a certain amount of separation between signals. Still greater selective action can be obtained by the use of additional suitably adjusted resonant circuits located somewhere in the receiver in such a way as to reject all but the desired signal. The ability to discriminate between radio waves of different frequencies is called selectivity and the process of adjusting circuits to resonance with the frequency of a desired signal is spoken of as tuning. Although intelligible radio signals have been received from the stations thousands of miles distant, using only the energy abstracted from the radio wave by the receiving antenna much more satisfactory reception can be obtained if the received energy is amplified. This amplification may be applied to the radio-frequency currents before detection, in which case it is called radio-frequency amplification or it may be applied to the rectified currents after detection, in which case it is called audio-frequency amplification. The use of amplification makes possible the satisfactory reception of signals from waves that would otherwise be too weak to give an audible response. The process by which the signal being transmitted is reproduced from the radio-frequency currents present at the receiver is called detection, or sometimes demodulation. Where the intelligence is transmitted by varying the amplitude of the radiated wave, detection is accomplished by rectifying the radio frequency current. The rectified current thus produced varies in accordance with the signal originally modulated on the wave irradiated at the transmitter and so reproduces the desired signal. Thus, when the modulated wave is rectified, the resulting current is seen to have an average value that varies in accordance with the amplitude of the original signal. Receiver circuit are made up a of a number of stages. A stage is a single transistor connected to components which provide operating voltages and currents and also signal voltages and currents. Each stage has its input circuit from which the signal comes in and its output circuit from which the signal, usually amplified, goes out. When one stage follows another, the output circuit of the first feeds the signal to the second. And so the signal is amplified, stage by stage, until it strong enough to operate the loudspeaker. Radio Waves Radio Waves are a member of the electromagnetic of waves. They are energy-carriers which travel at the speed of light (ν), their frequency(?) and wavelength(λ) being related , as for any wave motion, by the equation ν=?* λ where ν=c=3.0*108 m/s in a vacuum (or air). If λ=300m, then ?=ν/λ=3.0*108 /(3.0*10 2)=106Hz=1MHz. The smaller λ is, the larger ?. Radio Waves can be described either by their frequency or their wavelength. But the former is more fundamental since, unlike λ (and ν ), f does not change when the waves travel form one medium to another. Radio Waves can travel form a transmitting aerial in one or more of three different ways. Surface or ground wave.. This travels along a ground, the curvature of the earth’s surface. Its range is limited mainly by the extent to which energy is absorbed form it by the ground. Poor conductors such as sand absorb more strongly that water, and the higher the frequency the greater the absorption. The range may be about 1500km at low frequencies (long wave, but much less for v. h. f.). Sky wave. This travels skywards and, if it is below a certain critical frequency (typically 30MHz), is returned to earth by the ionosphere. This consists of layers of air molecules (the D,E and F layer), stretching form about 80km above the earth to 50km, which have become positively charged through the removal of electrons by the sun’s ultraviolet radiation. On striking the earth the sky wave bounces back to the ionosphere where it is again gradually refracted and returned earthwards as if by 'reflection '. This continues until it is completely attenuated. Space wave. For v. h . f., u. h. f. and microwave signals, only the space wave, giving line-of sight transmission, is effective. A range of up to 150km is possible on earth if the transmitting aerial is on high ground and there are no intervening obstacles such as hills, buildings or trees. Oscillators Electrical oscillators are widely used in radio and television transmitters and receivers, in signal generators, oscilloscopes and computers, to produce A.C. with waveforms which may be sinusoidal, square, sawtooth etc. and with frequencies from a few hertz up to millions of hertz. Oscillatory circuit When a capacitor discharges through an inductor in a circuit of low resistance, an A.C. flows. The circuit is said to oscillate at its natural frequency which, as we will show shortly, equals, i.e. its resonant frequency f0. Electrical resonance thus occurs when the applied frequency equals the natural frequency as it does in a mechanical system.. In Fig,2-2(a) , a charged capacitor C is shown connected across a coil L.C immediately starts to discharge, current flows and a magnetic field is created which induces an e. m. f. in L. This e. m. f. opposes the current . When C is completely discharged the electrical energy originally stored in the electric field between its plates has been transferred to the magnetic field around L. By the time the magnetic field has collapsed, the energy is again stored in C. Once more C starts to discharge but current now flows in the opposite direction, creating a magnetic field of opposite polarity. When this field has decayed, C is again charged with its upper plate positive and the same cycle is repeated. In the absence of resistance in any part of the circuit , an undamped sinusoidal A.C. would be obtained. In practice , energy is gradually dissipated by resistance as heat and a damped oscillation is produced. Oscillator As the resistance of an LC circuit increases, the oscillation decay more quickly. To obtain undamped oscillations, energy has to be fed into the LC circuit in phase with its natural oscillations to compensate for the energy dissipated in the resistance of the circuit. This can be done with the help of a transistor in actual oscillators. A simple tuned oscillator is shown in Fig.2-2(b). The LC circuit is connected in the collector circuit (as the load) and oscillations start in it when the supply is switched on . The frequency of the oscillations is given by, i.e. then natural frequency of the LC circuit. The transistor merely ensures that energy is fed back at the correct instant from the battery. The current bias for the base of the transistor is obtained through R . AMPLIFIER Introduction The term amplifier is very generic. In general, the purpose of an amplifier is to take an input signal and make it stronger (or in more technically correct terms, increase its amplitude). Amplifiers find application in all kinds of electronic devices designed to perform any number of functions. There are many different types of amplifiers, each with a specific purpose in mind. For example, a radio transmitter uses an RF Amplifier (RF stands for Radio Frequency); such an amplifier is designed to amplify a signal so that it may drive an antenna. This article will focus on audio power amplifiers. Audio power amplifiers are those amplifiers which are designed to drive loudspeakers. Specifically, this discussion will focus on audio power amplifiers intended for DJ and sound reinforcement use. Much of the material presented also applies to amplifiers intended for home stereo system use. The purpose of a power amplifier, in very simple terms, is to take a signal from a source device (in a DJ system the signal typically comes from a preamplifier or signal processor) and make it suitable for driving a loudspeaker. Ideally, the ONLY thing different between the input signal and the output signal is the strength of the signal. In mathematical terms, if the input signal is denoted as S, the output of a perfect amplifier is X*S, where X is a constant (a fixed number). The "*" symbol means? Multiplied by". This being the real world, no amplifier does exactly the ideal, but many do a very good job if they are operated within their advertised power ratings. The output of all amplifiers contain additional signal components that are not present in the input signal; these additional (and unwanted)characteristics may be lumped together and are generally known as distortion. There are many types of distortion; however the two most common types are known as harmonic distortion and inter modulation distortion. In addition to the "garbage" traditionally known as distortion, all amplifiers generate a certain amount of noise (this can be heard as a background "hiss" when no music is playing). More on these later. All power amplifiers have a power rating, the units of power are called watts. The power rating of an amplifier may be stated for various load impedances; the units for load impedance are ohms. The most common load impedances are 8 ohms, 4 ohms, and 2 ohms (if you have an old vacuum tube amplifier the load impedances are more likely to be32 ohms, 16 ohms, 8 ohms, and maybe 4 ohms). The power output of a modern amplifier is usually higher when lower impedance loads (speakers) are used (but as we shall see later this is not necessarily better). In the early days, power amplifiers used devices called vacuum tubes (referred to simply as "tubes" from here on). Tubes are seldom used in amplifiers intended for DJ use (however tube amplifiers have a loyal following with musicians and hi-fi enthusiasts). Modern amplifiers almost always use transistors (instead of tubes); in the late 60's and early 70's, the term "solid state" was used (and often engraved on the front panel as a "buzz word"). The signal path in a tube amplifier undergoes similar processing as the signal in a transistor amp, however the devices and voltages are quite different. Tubes are generally "high voltage low current" devices, where transistors are the opposite ("low voltage high current"). Tube amplifiers are generally not very efficient and tend to generate a lot of heat. One of the biggest differences between a tube amplifier and a transistor amplifier is that an audio output transformer is almost always required in a tube amplifier (this is because the output impedance of a tube circuit is far too high to properly interface directly to a loudspeaker). High quality audio output transformers are difficult to design, and tend to be large, heavy, and expensive. Transistor amplifiers have numerous practical advantages as compared with tube amplifiers: they tend to be more efficient, smaller, more rugged (physically), no audio output transformer is required, and transistors do not require periodic replacement (unless you continually abuse them). Contrary to what many people believe, a well designed tube amplifier can have excellent sound (many high end hi-fi enthusiasts swear by them). Some people claim that tube amplifiers have their own particular "sound". This "sound" is a result of the way tubes behave when approaching their output limits (clipping). A few big advantages that tube amplifiers have were necessarily given up when amplifiers went to transistors. What are Amplifier Classes? The Class of an amplifier refers to the design of the circuitry within the amp. There are many classes used for audio amps. The following is brief description of some of the more common amplifier classes you may have heard of. Class A: Class A amplifiers have very low distortion (lowest distortion occurs when the volume is low) however they are very inefficient and are rarely used for high power designs. The distortion is low because the transistors in the amp are biased such that they are half "on" when the amp is idling. As a result, a lot of power is dissipated even when the amp has no music playing! Class A amps are often used for "signal" level circuits (where power is small) because they maintain low distortion. Distortion for class A amps increases as the signal approaches clipping, as the signal is reaching the limits of voltage swing for the circuit. Also, some class A amps have speakers connected via capacitive coupling. Class B: Class B amplifiers are used in low cost, low quality designs. Class B amplifiers are a lot more efficient than class A amps, however they suffer from bad distortion when the signal level is low (the distortion is called "crossover distortion"). Class B is used most often where economy of design is needed. Before the advent of IC amplifiers, class B amplifiers were common in clock radio circuits, pocket transistor radios, or other applications where quality of sound is not that critical. Class AB: Class AB is probably the most common amplifier class for home stereo and similar amplifiers. Class AB amps combine the good points of class A and B amps. They have the good efficiency of class B amps and distortion that is a lot closer to a class A amp. With such amplifiers, distortion is worst when the signal is low, and lowest when the signal is just reaching the point of clipping. Class AB amps (like class B) use pairs of transistors, both of them being biased slightly ON so that the crossover distortion (associated with Class B amps) is largely eliminated. Class C: Class C amps are never used for audio circuits. They are commonly used in RF circuits. Class C amplifiers operate the output transistor in a state that results in tremendous distortion (it would be totally unsuitable for audio reproduction). However, the RF circuits where Class C amps are used employ filtering so that the final signal is completely acceptable. Class C amps are quite efficient. Class D: The concept of a Class D amp has been around for a long time, however only fairly recently have they become commonly used. Due to improvements in the speed, power capacity and efficiency of modern semiconductor devices, applications using Class D amps have become affordable for the common person. Class D amplifiers use a very high frequency signal to modulate the incoming audio signal. Such amps are commonly used in car audio subwoofer amplifiers. Class D amplifiers have very good efficiency. Due to the high frequencies that are present in the audio signal, Class D amps used for car stereo applications are often limited to subwoofer frequencies, however designs are improving all the time. It will not be too long before a full band class D amp becomes commonplace. Other classes: There are many other classes of amplifiers, such as G, H, S, etc. Most of these are variations of the class AB design, however they result in higher efficiency for designs that require very high output levels (500W and up for example). At this time I will not go into the details of all of these other classes as I have not studied them all in detail. Suffice to be aware that they exist for now. 無線電接收機 圖2-4為無線電接收機的方框圖,輸入信號為調幅無線電波。它的基本組成包括天線、調諧回路、混頻器、本振電路、中放放大器、檢波器、音頻放大器、喇叭、電源等。 任何天線系統既能輻射無線電波又能接收無線電波。任何經過天線的無線電波均能在天線中感應電壓，因此，接收機必須能夠從天線所收到的所有信號中分離出有用信號。這個分離過程是根據發射端發射的信號頻率不同，利用調諧回路完成的。調諧回路能夠有效地從眾多頻率中選擇出某一個特定頻率。通過天線調諧回路對某一特定頻率地諧振，可以使天線從這一特定頻率中吸收的能量比從其他平頻率中吸收的能量大得多，這樣，就從某種程度上實現了信號的分離。進一步的選擇作用可以通過接收機中的某些經過適當調諧的諧振回路實現，以這種方式進一步去除了有用信號以外的其他信號。將不同頻率的無線電波加以區別的能力稱為選頻，將諧振回路的頻率調在有用信號頻率上的過程稱為調諧。 盡管接收的有用信號來自幾千里以外，但如果經過放大，通過天線獲得的信號還是具有令人滿意的效果。放大過程可能應用在對檢波前的射頻電流，這種情況稱為射頻放大；也可應于檢波后，這種情況稱為音頻放大。放大器的應用使令人滿意的接收成為可能，否則，有些太弱的信號不能獲得好的收聽效果。 從射頻信號中重視被傳輸?shù)脑夹盘柕倪^程稱為檢波或解調。如果有用信號在發射時是通過改變信號的振幅（即調幅），則檢波就是通過對射頻電流進行整流完成的。整流電流隨著原始調制信號而變化，從而沖縣了原始的有用信號，這樣，已調波被整流而產生的電流可以被看成隨原始信號幅度變化的平均值電流。 接收機的電路由多級組成。每級由晶體管與提供工作電壓、電流和信號電壓、電流的元件相連構成，每級都有輸入回路，它讓信號進入；有輸出回路，它讓通常是放大后的信號輸出。當一級接一級時，第一級的輸出回路將信號饋送給第二級，信號經過逐級放大，直到足以推動揚聲器。 無線電波 無線電波是電磁波大家族中的一員，它們攜帶能量且以光速在空氣中傳播，它們的頻率與波長相關，即任何電磁波傳播時，有 ν=?* λ 這里，ν=c=3.0*108 m/s（在空氣中），如果λ=300m,則?=ν/λ=3.0*108 /(3.0*10 2)=106Hz.=1MHz。波長λ越小，頻率?越高。 無線電波既能用頻率又能用波長來描述。但前者更常用，因為頻率不像速度，不會因傳播媒介的改變而變化。 從天線電波輻射出去的無線電波通常以三種形式傳播。 （a）地表波或地波。這種波按地球表面的曲度，沿地表面?zhèn)鞑?。它的傳播范圍有限，其能量易被地表面吸收。惡劣的地形條件如沙漠比水面更易吸收能量。頻率越高，能量被吸收得越多。低頻波（長波）的傳播范圍約為1500千米。高頻波的查范圍要小得多。 （b）天波。沿天空傳播，若低于某個關鍵頻率（如30MHZ），會被電離層反射回地面。電離層由空氣分子層組成（包括D、E、F層），位于地球上方80千米到500千米處，它由于太陽紫外線的輻射而失去電子，因而帶正電荷。反射回地面的天波又從地面反射回電離層，并再次被反射回地面，如此反復多次直到能量完成衰減。 (c) 空間波。甚高頻、超高頻和微波只能以空間波的形式才能有效 傳播，空間波也稱視距傳播。如果天線架設很高且沒有障礙阻隔，如高山、建筑物、大樹等，空間波的傳播距離可達150千米 振蕩器 電子振蕩器廣泛用于廣播、電視發射機、接收機、信號發生器、示波器及計算機中，它被用來產生幾赫茲到幾百萬赫茲的各種波形，如正弦波、方波、鋸齒波等。 振蕩電路 在一個低阻的RC 回路中，電容通過電感放電，回路中有交流電流流過，則稱回路發生了振蕩，其振蕩頻率等于，正好等于它的諧振頻率 f0 。當外加信號頻率等于回路的固有振蕩頻率時，回路發生諧振，這也和機械振動系統相似。 再圖2-1（a）中，一個充電的電容和一個電感線圈相連，電容立刻開始放電，電流流過電感并在其中產生磁場和感應電動勢，這個感應電動勢與電流相反。當電容放電完成以后，兩金屬片之間電場中儲存的電場能全部轉變成了電感中的電磁能。 然后，電感對電容反充電，電場能重新儲存在電容中。當電容再次放電，回路電流反相，再電感中產生極性相反的電磁場。然后電感再次放電，電容再次充電，電流再次反相，這個過程不斷重復。 若電路中無電阻，則可獲得無衰減的正弦交流電流。實際上，由于回路損耗電阻的存在，能量會逐漸以熱能的形式消耗掉，產生的 是一個逐漸衰減的振蕩波形。 振蕩器 當振蕩電路的電阻增加，振蕩迅速衰減。為了獲得不衰減的振蕩信號，必須對LC回路饋入能量，以補充因回路電阻而損耗的能量，這在實用振蕩電路中是通過晶體管完成的。 一個簡單的調諧振蕩器如圖2-2（b）所示，LC回路接在晶體管的集電極回路（作為負載），當開關合上時，振蕩開始，振蕩頻率由LC回路的諧振頻率決定。晶體管只是將電源的能量饋給振蕩回路以保證正常的狀態，晶體管的基極偏置電流由電阻R獲得。 放大器 這種放大器是非常常見的，通常來說，這個放大器的目的是用來接收一個信號并使之放大，放大器常常應用在各種電子設備中，用來執行各種功能。各種不同類型的放大器有不同的用途。例如，音頻傳送使用RF放大器，（RF表示音頻）；這樣的放大器用來放大從天線接收來的信號，這篇文章將著重介紹音頻放大器，這種音頻放大器來驅動揚聲器。特殊的，下面討論的是為DJ和音頻放大，大部分的放大器應用于家庭立體聲系統。 簡單來說，放大器的目的是從一個信號源得到一個信號并放大能使它去驅動揚聲器，唯一不同的是：輸出信號是輸入信號的放大。從數學角度來說，如果輸入信號定義為S，則輸出信號為X*S，X為放大系數常量。*代表乘運算。 在現實當中，沒有一種放大器是理想的，在先進的設備中它們能更好的工作。放大器的輸出包含一些輸入信號沒有的訊雜信號，這種訊雜信號被集中到一塊現象統稱為失真。------ 失真的類型很多，最常見的兩種失真是調諧失真和交調失真，額外的無用信號通常被成為失真，所有的放大器都能產生一定量的噪音，更詳細的內容將在以后介紹。 放大器 所有放大器都有一定放大系數，它的基本單位被稱為瓦特。放大器的系數決定了它的負載阻抗，它的基本單位被稱為歐姆。常用的阻抗有8歐姆、4歐姆、2歐姆，當?shù)妥杩关撦d被使用時放大器的放大系數會更高。 在早期，放大器設備是電子管來實現的，電子管很少被使用在DJ中，現代放大器都使用的是晶體管，晶體管和真空放大器在信號傳輸過程中經歷了相似的過程，但他們工作環境有一些區別，電子管一般是高壓低流，而晶體管則相反，電子管的效率不是很高，并且會發熱，電子管放大器與晶體管放大器的一個最大的區別是真空放大器在音頻輸出上要求更高，高品質的音頻傳輸器是很難設計的，設計起來更困難，更昂貴。晶體管放大器比電子管放大器更有實用價值，因為它具有高效、小而耐用，沒有音頻的傳輸是必須的，晶體管不需要周期性替換，與人們所通常認為不同的是，好的電子管放大器能產生高品質的聲音，有些人認為電子管有他們獨特的“聲音”。這個“聲音”是當他們達到極限時產生的結果。晶體管放大器代替了電子管放大器是有很大益處的。 放大器的種類 放大器的種類通常是按照放大電路來設計的，在音頻放大有許多種類，下面簡要介紹常用放大器的種類 A類 A類具有非常低的失真，盡管他們效率非常低，很少用在高效率放大器中。它的失真很低是因為當空載時放大器工作在放大區的中點，結果，許多能量在無信號輸入時已經被消耗掉了，因為A類放大器具有低失真的特性，所以常常當在放大器的前級，作為在電路中信號到達電壓擺動的極限時，A類放大器的失真產生了消波，A類放大器是通過電容偶合連接揚聲器的。 B類 B類放大器通常被使用在廉價、低品質設計中，比起A類放大器，B類放大器有更高的效率，然而，當信號弱時會產生交迭失真，B類常常用在經濟型電路中。在IC放大器出現之前，B類放大器一般用在收音機電路，便攜式收音機以及對音質要求不高的電路中。 AB類 AB類在家庭立體聲和相似放大器最常用的一種放大器，AB類放大器綜合了A類B類放大器的優點。它具有B類放大器的高效率和A類放大器的低失真?？朔薆類弱信號失真和A類的削波失真。AB類放大器使用的是一副晶體管，它都處于低導通狀態，這樣更大消除了交迭失真。 C類 C類放大器常常不用在音頻電路中。她們通常用在RF電路中。C類放大器工作在具有大失真的晶體管電路中，C類放大器使用在帶濾波的RF電路從而使信號在最后完整的接收，C類放大器的效率是很高的。 D類 D類放大器的概念已經出現很長時間了，盡管到目前才被普遍使用。在快速發展以后，隨著高容量、高效率現代半導體設備的出現，普通人使用D類放大器也成為了現實。D類放大器可應用與把音頻信號調制到高頻信號，這種放大器通常用在輔助低音頻信號，這種D類放大器具有很好的效率。使