購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。帶三維備注的都有三維源文件，由于部分三維子文件較多，店主做了壓縮打包，都可以保證打開的，三維預覽圖都是店主用電腦打開后截圖的，具體請見文件預覽，有不明白之處，可咨詢QQ:1304139763
摘 要
本次畢業設計的的題目是連桿的工藝工裝及夾具設計。連桿是柴油機的主要傳動件之一，連桿是汽車發動機中的主要傳動部件之一，它在柴油機中，把作用于活塞頂面的膨脹的壓力傳遞給曲軸，又受曲軸的驅動而帶動活塞壓縮氣缸中的氣體。本文主要論述了連桿的加工工藝及其夾具設計。連桿的尺寸精度、形狀精度以及位置精度的要求都很高，而連桿的剛性比較差，容易產生變形，因此在安排工藝過程時，就需要把各主要表面的粗精加工工序分開。逐步減少加工余量、切削力及內應力的作用，并修正加工后的變形，就能最后達到零件的技術要求。
關鍵詞: 連桿；變形；加工工藝；夾具設計
Abstract
The connecting rod is one of the main driving medium of diesel engine, this text expounds mainly the machining technology and the design of clamping device of the connecting rod. The precision of size, the precision of profile and the precision of position , of the connecting rod is demanded highly , and the rigidity of the connecting rod is not enough, easy to deform, so arranging the craft course, need to separate the each main and superficial thick finish machining process. Reduce the function of processing the surplus , cutting force and internal stress progressively , revise the deformation after processing, can reach the specification requirement for the part finally .
Keyword: Connecting rod；Deformination；Processing technology；Design of clamping device
目 錄
摘要···········································································································································Ⅰ
Abstract························································································································Ⅱ
緒論·············································································································································1
1 連桿加工工藝························································································································2
1.1 連桿的結構特點··············································································································2
1.2 連桿的主要技術要求······································································································2
1.2.1 大、小頭孔的尺寸精度、形狀精度···········································································3
1.2.2 大、小頭孔軸心線在兩個互相垂直方向的平行度···················································3
1.2.3 大、小頭孔中心距·······································································································3
1.2.4 連桿大頭孔兩端面對大頭孔中心線的垂直度···························································3
1.2.5 大、小頭孔兩端面的技術要求···················································································4
1.2.6 2-Φ15螺栓孔的技術要求··························································································4
1.2.7 有關2-Φ15孔兩端面的技術要求··············································································4
1.3 連桿的材料和毛坯········································································································4
1.4 連桿的機械加工工藝過程····························································································6
1.5 連桿的機械加工工藝過程分析······················································································7
1.5.1 工藝過程的安排···········································································································7
1.5.2 定位基準的選擇···········································································································8
1.5.3 確定合理的夾緊方法 ·································································································8
1.5.4 連桿兩端面的加工 ·····································································································9
1.5.5 連桿大、小頭孔的加工·······························································································9
1.5.6 連桿2-Φ15螺栓孔的加工· ·······················································································9
1.6 確定各工序的加工余量、計算工序尺寸及公差·························································9
1.7 工時定額的計算 ··········································································································11
1.7.1粗銑連桿大小頭上端面·······························································································11
1.7.2粗銑連桿大小頭下端面·······························································································12
1.7.3粗鏜、半精鏜Φ70H7孔、Φ46H7孔··············································································12
1.7.4精銑連桿大頭Φ70H7孔兩端面·················································································13
1.7.5粗銑、精銑2-Φ15螺紋孔兩端面············································································14
1.7.6銑寬60兩側面···········································································································15
1.7.7銑寬64兩側面···········································································································15
1.7.8鉆、擴、鉸2-Φ15H8螺栓孔并倒角C1、C1.5······················································16
1.7.9鉆2-Φ7孔·················································································································17
1.7.10鉆2-Φ5孔（頭部Φ10，角度90）····································································17
1.7.11精鏜Φ70H7孔、Φ46H7孔并倒角C1····································································18
1.7.12半精鏜、精鏜Φ40H7銅套孔··················································································18
1.8 連桿的檢驗··················································································································19
1.8.1 觀察外表缺陷及目測表面粗糙度···········································································19
1.8.2 連桿大頭孔圓柱度的檢驗·······················································································19
1.8.3 連桿體、連桿上蓋對大頭孔中心線的對稱度的檢驗···········································19
1.8.4 連桿大小頭孔平行度的檢驗···················································································20
2 夾具設計······························································································································21
2.1問題的提出···················································································································21
2.2 夾具設計······················································································································21
結論·········································································································································23
致謝·········································································································································24
參考文獻·································································································································25
VI