購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814

無錫職業技術學院畢業設計說明書 乘客電梯的PLC控制 摘要：國民經濟的飛速發展, 現代化程度日益提高,高層建筑愈來愈多, 電梯也隨之增多, 電梯產品在人們物質文化生活中的地位得到了提高,成為重要的運輸設備之一。國內傳統的電梯控制一是由繼電器、接觸器構成。它不僅存在著可靠性差、成本高、故障率高等缺點,而且在層數增加時,配線變化給制造及安裝帶來諸多不變。若用PLC 控制就解決了以上的不足。 本設計就以PLC作為工具對升降電梯的各種操作進行控制。先對四層電梯的硬件部分作分析，看需要什么樣的開關，電機，信號燈等。然后，畫出它的控制面板圖，再根據控制面板圖估計一下I/O點數，這樣可以確定所選機型，然后在軟件設計，寫出流程圖，梯形圖，寫出語句。最后是進行調試，看看此程序是否可行。 關鍵詞：PLC控制系統 電梯 繼電器 接觸器 PLC control of passenger Elevator Abstract: The rapid development of the national economy, the increasing degree of modernization, more and more high-rise buildings, elevators also will be increased, Elevator products in people's material and cultural life of the status has been enhanced to become one of the important transport equipment. Traditional domestic elevator control from the first relay, a contactor. It is not only poor in the reliability, high cost, high failure rate shortcomings, but also in layers increases, changes to the wiring and installation of manufacturing has brought many unchanged. If the control by PLC to address the above shortcomings. the design of the PLC as a tool to the elevators for various operating control. Elevator on the first four parts of the hardware analysis, the need to see what kind of switches, motors, lights, etc.. Then, the control panel draw maps, plans, under the control panel is estimated to I / O points, so certain selected models, and then softwaredesign, write flowchart, ladder diagram, write statements. Finally,debugging and look at the feasibility of this procedure. Key words: PLC control system Elevator relay contactor