外文翻譯--萬向節十字軸總成失效分析【中英文文獻譯文】,中英文文獻譯文,外文,翻譯,萬向節,十字,總成,失效,分析,中英文,文獻,譯文 外文文獻 Cross-axis gimbal assembly Failure Analysis The main function of joints in different axis passing between the rotating shaft torque, it has been widely used in various types of truck axle shaft connected between the cross section, usually in the course of cross-axis universal joint of the Needle Roller Bearings for rotary movement is not, but for the rotation of the swing movement, the load cycle changes submitted. Based on the heavy-duty vehicle WX0082 Cross-axis gimbal assembly of less than life pieces of the failure mode of failure, failure, structural parameters and materials used and the performance of finite element analysis and other methods to conduct a comprehensive comparative analysis of product performance a design improvement. ? 1. Oblique imprint The author of a company from the provision of three packs of the three packs of Service returned failure cases observed that the cross-axis oblique journal imprint is relatively serious, bearing rings also produce the inner wall of the imprint, but the depth of cross-axis than the light. By the analysis of joints installed on the bearing assembly, when the total space bearing a larger circle, the needle easily skewed, with the result that journal have a cross-axis tilt angle with the axis of the embossing, the embossing depth of the expansion of more deep, the needle will not be able to spin, thus increasing frictional resistance, exacerbated by the extension of indentation. The total circumference of its appropriate space should be controlled in the range of 0.1 ~ 0.4mm inside, JB/T3232 in a given space for a total circumference of not more than 0.5mm. 2. Fatigue spalling Shaft angle in the use of a smaller state, universal joint assembly of the needle bearing journal diameter and cross-axis angle in the framework of repeated smaller swing, when the cross-axis with the bearing radial clearance with the wear and tear expansion will lead to concentration of load, the load will be large local indentation fatigue prematurely in order to develop into a large area off the fatigue. Especially in the cross-axis the first axis, the stress concentration due to the impact of parts of their set was almost all the chamfering eat, severe high temperature sintering under a state of the phenomenon. Because users do not use lubricants or as a result of time added on the universal joints bearings sealed properly, resulting in early loss of oil-bearing materials as well as the dust temperature intolerance, lip oil seals in the winter cold weather aging cracks under so that the early loss of grease. In addition, the universal joint assembly less oil in operation due to high temperature generated, so that shaft bearings and killed, resulting in a broken needle and the damage to seals and dust jacket, traces of ferrule surface ablation, the failure mode of both failure mode is non-normal. 4. Needle failure I lapsed from the universal joint assembly observed in the sample found that the majority of needle point of the surface there are Ma, Ma Hang, and large-scale fatigue spalling, a small number of needle head was broken, a small number of needle from the needle about 1.5mm Department head Ma Hang, and the existence of a larger phenomenon of bite wounds, the majority of needle fracture fracture from here, this occurrence of the main bearing structure and the size parameters and the circular design of the total gap. 5. Gasket failure Gasket is the first universal joint assembly of the components failure, the form of gasket failure nylon fracture and wear pads. I carefully analyzed samples gasket failure found that the outer gasket has obvious cracks, gasket has cracks and debris outside. Obviously, the gasket is the gasket by the external force resulting in rise of the local stress concentration, once the gasket external damage to the axial force will be borne by the rest of the pads to bear, the bear pads per unit area will increase the power, the entire pad tablets to be broken. Hence the need for well-designed shape and bearing structure pads. At the same time, each gasket failure due to damage and wear has been associated with failure, the gasket material must be selected high strength and wear resistance of materials. 6. Cross-axis fracture Cross shaft fracture is usually a serious overloading the user under the premise of the factors or unusual conditions occur, as joints in the design of the Department of full compliance with the standards of universal joints JB/T8925-2008 static torsional strength safety factor of 2.5 times the provisions of However, OEMs fault occurred during the three packs of the proportion of the total failure still accounts for 2% ~ 5% of such cases is sudden, but inevitable, universal joints and therefore the static torsional strength of match, we must maximum output torque in the engine 3 times more specific in order to avoid overloading caused the emergence of sudden failure. 7. Metallographic test analysis Cases of failure to carry out physical and chemical analysis, respectively, in the cross shaft, ferrule and needle selection of the typical characteristics of the location of the site, cutting under the specimen and along the vertical cross-section metallographic sample preparation, the microstructure-level qualified. To determine the cross shaft, ferrule and the center needle hardness, respectively, by micro-hardness of various parts of a gradient distribution of Vickers hardness measured, and its basically in line with the hardness of the hardness distribution. Check the cross-axis universal joints, a test piece of the outer ring and a number of needle samples in 50% hydrochloric acid aqueous solution heated to 70 ~ 80 ℃, heating of about 1h, check for hot acid found in various parts use burn phenomenon exists. This burn is to determine universal joints sealed as a result of poor performance and fat loss properties of the oil well, resulting in fever bearing universal joints burn too soon after the failure of the parts. 中文翻譯 萬向節十字軸總成失效分析 萬向節的主要作用是在不同軸線上的軸之間傳遞旋轉轉矩，它被廣泛應用于各類卡車的傳動軸聯接軸節叉之間，通常在使用過程中萬向節十字軸上的滾針軸承不是作旋轉運動，而是作旋轉擺動的運動，其載荷呈交變的周期變化。本文是通過對重型載車用WX0082萬向節十字軸總成壽命不足失效件的失效形式、失效原因進行分析。 分析結果如下： 1.斜壓印 從某公司三包服務處提供的三包退回失效件中觀察到，十字軸軸頸斜壓印情況比較嚴重，軸承套圈內壁也產生相應的壓印，但深度要比十字軸輕。經分析，安裝在萬向節總成上的軸承，當軸承圓周總間隙較大時，滾針易產生歪斜，致使十字軸軸頸產生與軸線傾斜一定角度的壓印，當壓印深度擴展較深時，滾針就不能自轉，因此使摩擦阻力增大，加劇壓痕的延伸。其合適的圓周總間隙應控制在0.1～0.4mm范圍內，JB/T3232中給定的圓周總間隙為不超過0.5mm。 2.疲勞剝落 在傳動軸擺角較小的使用狀態下，萬向節總成上的滾針軸承內徑與十字軸軸頸在較小角度范圍內反復擺動，當十字軸與軸承徑向游隙隨著磨損而擴大時，會導致產品載荷集中，載荷大的地方就會過早地產生疲勞壓痕，從而發展成為大面積的疲勞剝落。特別是在十字軸軸頭處，由于應力集中影響，其受載部位的倒角幾乎全部被啃掉，嚴重時會在高溫狀態下出現燒結現象。 3.缺油燒蝕 由于在使用過程中用戶不按期加注潤滑油或由于萬向節上的軸承密封不好，導致軸承早期失油以及防塵罩材料不耐低溫，油封唇口在冬季寒冷氣候下產生老化裂紋，使?jié)櫥缙诹魇?。另外，萬向節總成在運行中因缺油而產生高溫，使軸承與軸徑咬死，致使?jié)L針折斷以及密封和防塵外罩損壞，套圈表面有燒蝕痕跡，這種失效形式均屬于非正常失效形式。 4.滾針失效 從萬向節總成失效樣品中觀察發現，大多數滾針表面都存在麻點、麻坑和大面積疲勞剝落，少數滾針頭部被折斷，少數滾針在離滾針頭部1.5mm左右處存在較大麻坑和啃傷現象，滾針斷裂大部分也是從此處斷裂，這種情況的發生主要與軸承結構尺寸參數及圓周總間隙設計有關。 5.墊片失效 墊片是萬向節總成中首先失效的部件，墊片失效形式為尼龍墊片斷裂和磨損。仔細分析失效墊片樣品發現，墊片的外圍有明顯的裂紋，墊片外圍有裂紋及碎片。很明顯，墊片外圍是墊片受漲力致使應力集中的地方，一旦墊片外圍破壞，其軸向力將全部由余下的墊片承受，墊片單位面積上承受的力將增加，整個墊片將被破壞。因此需要設計合理的墊片形狀和軸承結構。同時，由于墊片每次失效破壞都伴隨著磨損失效，所以墊片材料必須選取強度和耐磨性較高的材料。 6.十字軸斷裂 十字軸的斷裂一般是在用戶嚴重超載前提下或異常因素條件下發生，因?yàn)槿f(wàn)向節在設計時完全遵循部標準JB/T8925-2008中萬向節靜扭強度安全系數2.5倍的規定，但在主機廠三包期內發生的故障比例仍占總故障的2％～5％，此種情況雖然是突發性的，但也不可避免，因此對萬向節的靜扭強度匹配，必須在發動機最大輸出扭矩的3倍以上才能避免特殊超載引起的突發性故障的出現。 7.金相檢驗分析 對失效件進行理化分析，分別在十字軸、套圈和滾針的典型部位選擇特征位置，切割下試件，并沿縱截面制取金相試樣，其金相組織級別合格。為確定十字軸、套圈及滾針的心部硬度，用顯微硬度計分別對各零件進行了維氏硬度梯度分布測定，其硬度也基本符合硬度分布規律。取萬向節的十字軸、外圈各一試件及數個滾針試件，在50%鹽酸水溶液中加熱至70～80℃，加熱約1h，作熱酸洗檢查，結果發現各零件在使用過程中都存在燒傷現象。這種燒傷現象判斷是由于萬向節密封性能差失油及油脂性能不好，導致萬向節軸承發熱后各零件燒傷過早失效。