壓縮包已打包上傳。下載文件后為完整一套設計?！厩逦?，無水印，可編輯】dwg后綴為cad圖紙，doc后綴為word格式，所見即所得。有疑問可以咨詢QQ 197216396 或 11970985

畢業設計任務書 課題： 機械式立體車庫 專 業 機械設計制造及其自動化 學 生 姓 名 　 班 級 學 號 指 導 教 師 專 業 系 主 任 　　　 發 放 日 期 年2月 20 日 一、設計內容 課題來源于工程實際。設計一機械式立體車庫，要求立體車庫至少存放20輛車。 設計的主要內容有： 1) 擬定總體方案和控制策略； 2）立體升降機構設計，橫移機構設計，零部件結構設計； 3）繪制總裝圖、部裝圖和零件圖。 1.總體設計 1）確定立體車庫的型式； 2）設計立體車庫的升降和橫移以及存取的傳動方案，繪制傳動原理圖； 3）確定車庫的總體結構，繪制總裝圖。 2.零部件的結構設計 1）選擇動力源； 2) 零部件的設計計算和校核； 3）零部件的結構設計，繪制部裝圖、零件圖； 二、設計依據 1．課題來源：生產實際； 2．產品名稱：機械式立體車庫； 3．結構形式：三層四列。 三、設計要求 1．能滿足快速存放要求，存取方便； 2．運行平穩，工作可靠，結構簡單，裝卸方便，便于維修、調整； 3．盡量使用通用件，以便降低制造成本； 4．便于控制； 5．設計圖樣總量：折合成A0幅面在3張以上；工具要求：應用計算機軟件繪圖；過 程要求：裝配圖需提供手工草圖； 6．畢業設計說明書符合相關要求； 7．查閱文獻資料10篇以上，并有不少于3000漢字的外文資料翻譯； 8．到相關單位進行畢業實習，撰寫不少于3000字實習報告； 9．撰寫開題報告 。 四、畢業設計物化成果的具體內容及要求 1、畢業設計要求 按教務處畢業設計（論文）格式規范統一編排、打印，字數不少于1萬字。 1）畢業設計說明書 1 份 2）傳動原理圖 1 張 3）總裝圖 1 張 4）部裝圖 　　 　　　　　 2 張 5）其它零件圖 　若干張 2、外文資料翻譯（英譯中）要求 1）外文翻譯材料中文字不少于3000字； 2）內容必須與畢業論文課題相關； 3）所選外文資料應是近10年的文章，并標明文章出處。 五、畢業設計進度計劃 起訖日期 工作內容 備 注 2月20日～2月21日 布置任務 2月21日～3月19日 調查研究，畢業實習，方案論證，總體設計 3月20日～4月7日 技術設計（部件設計） 4月7日～5月7日 工作設計（零件設計） 5月8日～5月25日 撰寫畢業設計說明書 5月26日～5月27日 畢業設計預答辯 5月28日～6月6日 修改資料 6月7日～6月8日 評閱材料 6月9日～6月10日 畢業答辯 6月11日～6月15日 材料整理裝袋 六、主要參考文獻： 1. 成大先.機械設計手冊[M]..北京：化學工業出版社，2004. 2. 機械設計手冊編委會.機械設計手冊[M].北京:機械工業出版社，2004. 3. 葉偉昌.機械工程及自動化簡明設計手冊(上冊)[M].北京：機械工業出版社，2001. 4、葉偉昌.機械工程及自動化簡明設計手冊(下冊)[M].北京：機械工業出版社，2001. 5. 饒振綱.行星齒輪傳動設計[M].北京：化學工業　出版社，2003. 6. 劉海江,于信匯.汽車齒輪[M].上海：同濟大學出版社，1997. 7. 鄧定瀛.自動變速器原理與運用[M].重慶：重慶大學出版社，2002. 8. 宋福昌.自動變速器的結構與檢修圖解[M].北京：中國電力出版社，2005. 9. 廖慶.垂直升降式機械立體停車系統的研究[D]. 武漢理工大學學位論文，2005. 10.白玉銘.垂直循環式立體車庫設計研究[D]. 哈爾濱工業大學學位論文，2007. 11.劉平輝.電梯升降式立體車庫曳引力的分析與計算[J]. 科技資訊，2009. 12.鄭鈞宜,李浩.電梯式立體車庫升降系統研究[J]. 中國水運（學術版），2006. 13.段文軍.機械式三維立體車庫機械結構及控制系統設計[D].北京工業大學碩士學位論文，2009. 14.唐義清,譚善文,唐義龍,郝慧鋒,謝武斌.基于單片機控制的機械式立體車庫[D].機械工程與自動化,2006. 15.荊友錄,欒德宇.立體車庫車輛存取機構的設計[D]. 山東:山東交通學院. 七、其他 八、專業系審查意見 系主任： 年 月 日 九、機械工程學院意見 院長： 年 月 日 5 英文原文 THE 6 LAYERS STEREO GARAGE DESIGN BASED ON OMRON PLC Zhuoran Zhang Department of Electrical & Engineering Wuhan Polytechnic University Wuhan, China E-mail: Harry zzr@126.com Zhe Mao, Hailing Wan Department of Electrical & Engineering Wuhan Polytechnic University Wuhan, China E-mail:maozhe998@ sina.com Abstract—with the development of the modern society, the number of the vehicles in these cities has been increasing with an exponential speed; especially the private cars, putting a great pressure on urban transportation and parking slot. This article is mainly concerned about the entire structure, running procedure and electrical system design including hardware and program design ideas for lifting-traversing stereo garage, which will not only shorten the developing period but also orient parking to centralization and automation direction; Owning some reference value. Keywords- Stereo Garage, Omron PLC, Design Insufficient parking slots is resulted from the development of the cities, economy and transportation of the cities, the traditional garages are always making the use of the nature vacancy, in a community, the ratio between parking slots and residents is approximately 1:1, one parking slot for a family at least, in order to solve the contradiction that the parking slots using precious commercial land, the stereo mechanical garages with the advantage of the average parking slot takes of less area have been gradually in front of us. Compared with the traditional underground parking garage, the stereo garages have more advantages. First of all, the stereo garages can save more area. The traditional ways must be amassed driving path for vehicles, averagely, a car will take up 40m2 If we take multi-layers garage (6 layers) in to consideration, it is possible for 13 cars to park in the area of 50m2, which will save lots of land resources and land construction expenditure. Meanwhile, the stereo garage could guarantee the safety of the people and their cars. If there is anybody in the garage or the cars are not fully stopped, the system controlled by electrical equipment will not run either. It means that, in the scale of the management, the mechanical garage could separate the people and vehicles, which makes it more systematically. Especially for underground garages, install this kind of garage will save a large area of illumination system, so it is also emerge conservation and environment protection. Ⅰ.THE CLASSIFICATION AND IMPLEMENT BACKDROP OF THE STEREO GARAGE A.THE CLASSIFICATION OF THE STEREO GARAGE According to the present development of the stereo garage, the stereo garage is including lifting-traversing, roadway stacking, vertical lifting, vertical circulating, circle level circulation; The concept of the stereo garage is all from automatic logistic material transmitting system. [3]The purpose of the stereo garage is to solve the parking problem in developed cities, that is make use of limited area to park more vehicles so as to save land resources of the cities and manage the static transportation of the urban. This article gives out a way to design lifting-traversing stereo garage based on Omron PLC CP1H, which could extend to solve relevant projects. B. A BRIEF INTRODUCTION TO LIFTING-TRAVERSING STEREO GARAGE. The modularization concept is imported in lifting-traversing stereo garage. It can be designed into two to five layers or half underground type, the number of the slot is from tens to hundreds. This kind of garage is suitable for both above ground and underground, the characteristics could be generalized as less occupation of land, simple structure, flexible configuration, lower cost in construction, decoration and fire protection and short period of construction; Safe and convenient for saving and taking cars; Smoothly operation, lower noise during running. [4] It is also appropriate for commercial, bureau and residential use. The safety equipment mainly is photoelectrical sensors, limiting displacement protector and emergency switch. C. THE ENTIRE FRAME OF THE SYSTEM As the fig. l representing, besides the central controller PLC, the stereo garage system could be divided into three sections: I. Mechanical System; It includes column, beam, carrying board, vehicle frame, hooks and etc. II. Electrical System; this section is the core of this article, which controls the whole system to operate. III. Touching Panel; it is the port from which operators and the system exchanging messages, operators could not only operate the system, but also in the situation of the malfunction, it could let operator enter the manual or debugging mode. Figure 1. The structure of the system Figure 2. Touch Screen (Auto running and Manual) ? THE MAIN HARDWARE OF THE SYSTEM We mainly use the Omron PLC CPH1, on considering the control requirement and the cost, we adopting CP1HX40DR-A PLC, the programming ways are ladder diagram or ST instruction list. The instruction length is 1 to 7 steps per instruction, each I/O relays has 1600 ports, USB 1.1 for communication. The display part, we import screen of WEINVIEW MT6056i series, the screen material is TFT, 5.6 inches, and the resolution is 320x234, with USB2.0 port supporting downloading. The frequency of the CPU is 400 MHz, 128RAM. D.THE SYSTEM STR UCTURE AND FUNCTIONS The mechanical parts cooperating with electrical system are carrying board, hooks and chains. There are 6 slots on each layer besides 7 slots on the top layer, totally 37 slots, the purpose for one slot empty on each layer is that making enough space for carrying board to move. The carrying boards of the first floor only design to traverse, also the top floor carrying boards are only supposed to lift. The other carrying boards among these floors are designed to life and traverse. In this way, this system could achieve the saving and taking from any slots among these 6 layers. In addition, this system has a touch screen system, which switches between auto run and manual debugging mode. Under the auto run mode, it could select a certain slot to accomplish saving and taking behavior, at the same time, monitoring the operation of the system. (Green words "System Running" in auto mode without malfunction). When failure occurs, the system seized and on screen flashing yellow failure code with red backdrop, with the help of the failure code, the professional operator could recognize and eliminate the failures promptly and accurately. On considering more authorities are given in manual debugging mode, to preclude unprofessional persons enter the mode by chance, before enter the mode, there is a cipher verification, in which the sequence could be set by ourselves. This would protect the system from potential dangers. Figure 2 is the graph of system auto running, manual and debugging. Ⅱ. THE COMPOSURE OF THE ELECTRICAL SYSTEM A. STRONG ELECTRICITY SYSTEM The strong power system includes power supply, protection and driving mechanism, here is electronic motors. Installing XJ3-D on the forepart of the power supply wire, which is used to protect phase sequence of the three-phase voltage, so that guarantee the right rotation of the motors. Moreover, the motors on some layers use the same three-phase voltage. B.THE SET OF THE MOTORS There are 6 traversing motors on the first layer, 6 traversing motors for 2 to 5 layers each, and so it is with lifting motors for 2 to 5 layers. The top layers have only 7 lifting motors. After setting the motors, mark every motor. For example, the motor driving the third slot of the second layer, we mark it with "23", the relay before the motor are named KM23. Here series connect all the motors' thermal protection, any motor's problem will stop the system. In this way, it has no influence on the stability of the system, but lowers the cost. At the same time, make it easier to find the problems. (What we need to do is press the thermal protection switch one by one). C .WEAK POWER SYSTEM The weak power system is also the control system, which are mainly the PLC mode and its 5 extended modules, also the sensors. As the figure below, on the right is the input part, DC 24V, on the left, is the output section, AC 220V, to connect with contactors and drive them. These device's functions have close relationships with the entire system's control requirements. On the above of the graph, the protection equipment are emergency switch, installed beside the touching panel, emergency only, trigger it, the system stops; Front and back photoelectrical sensors, which are used to detect people or unidentified objects breaking into the system, if this happens, the system would stop then response with photoelectrical failure, the goal is to protect the people and the vehicles. The phase sequence protection has been illustrated before; Over current protection normally activated under the motor stuck; All the margin switches series connected, cult the main power when any carrying board exceed the limiting position. Limit switches including up ones and down ones or left and right limit switches. In order to achieve the controlling requirements, the level limit switches are installed on the both side of the each slot frame, while the vertical limit switches are installed on the chain which attached to the motor. It is necessary to point out that the first layer only installed down and left right limit switches, the top layer only installed up switches these switches could sense the position of the carrying boards, helping to finish the lifting and traversing control; Hook position sensors is to fix the vehicles and sense the slot empty or not. The output points"00 04 05 06 07" are to select different phase for each layer, so control the motors' rotation ways. Figure 3. PLC Modules (Segment) There are other 4 extended modules, which only give more I/O ports to the system, similar to this main part. Ⅲ. OPERATION PROCEDURE A. TAKING PROCEDURE As far as the first layer concerned, it is only designed to traverse, so as to make space to upper layer's carrying boards to move downward. So do the other layers, which are designed to traverse. When traversing meet the requirements, lifting mechanism will run to put the carrying board down, finishing the saving and taking procedure. During the procedure the photoelectrical sensors are open and will behave as fore part has explained. In figure 2A, is the taking condition, at this time "Loading" will flash until the taking procedure finishes. When we enter "51", the system will distinguish whether the operation is a taking or a saving according to the hook of the 51 slot. Then prints the message responded to the state of the hook on the screen, the operator could confirm the operation or cancel it. On confirming, the 51 carrying board will wait for its downward boards to finish the traversing move then moving down. In addition, a timer is added to this control module in order to preclude level limit switches malfunction, resulting into the traversing move time up. If the time for traversing move exceeds the set time, the system will warn the operator "traversing move time up" which displays on the screen, the operator could check out the failure. The up limit switches are used to sense whether the carrying boards are stopped at their routine slots, which the level switches can't finish. Maybe one carrying board stuck between two layers. Only do all the upper layers' carrying boards stop at their routine slots, the selected carrying board's lifting move is activated. A timer is also set into the lifting control, with the same function as traversing timer. The elevator carries the vehicle down to the ground, release the hook, now the photoelectrical signal shut down, and waiting for the owners to take their vehicle. On driving away the vehicle and operator's confirming the photoelectrical signal resumes, the carrying board back to its slot from the down way. Figure 4. The flowchart of the taking and saving procedure B. SAVING PROCEDURE The saving process is based on taking procedure, so they are familiar; the only difference is the hook move. Ⅳ. SOFTWARE PROGRAMMING AND PROGRAMMING ENVIRONMENT A.SOFTWARE PROGRAMMING ENVIRONMENT AND ITS LANGUAGE In this system, we choose Omron CX-ONE 3.0 to program the PLC. The language for programming is classic ladder diagram. On considering the stereo garages are installed in different condition and requirement of different users, the scale of the stereo garages should be flexible, for example different layers or slots. In order to meet the different scales requirements, the program is modularized, only need to change the I/O ports, the logical relations in the ladder diagram are fixed. In this way, it is not only with highly compatibility but also shortens the period to develop relevant designs and make it easier to debugging and repair. B.MODULARIZED PROGRAM Conditional jumps are widely used in the programming; the entire program consists of different modules, on certain conditions, the program jumps. As illustrated before, there are only two movements for a carrying board, lifting or traversing, beside the boards of first and top layers. The condition for the fifth could traverse is all the upper layers slots' up limiting switches closed. Then "Traverse OK" is activated, and then the program will make analysis of the operation until meet set conditions, the program jumps. For the lifting movements are always with the downward movements, so program the downward standards, the system will run. The entire program is programmed with this method, above the passage, is only a traversing OK and vertical move OK module. Similarly, modules of a fixed slot, for example slot "21". "21 Traversing Move", "21 Vertical Move"; for whole system, "Emergency Stop and Protection", "Button Select", "System Monitor" and "Debugging" modules, which cooperate with each other to accomplish the control and monitor. Figure 5. Monitoring and Display module (Segment) Fig. 5 is the segment program of the monitoring module, all the motors' protection series connected, so are the phase sequence protection and margin switches. Any of them change; PLC will transfer messages to the screen, which displays. Meanwhile, cults off the main KM, the system stops. Ⅵ.A BRIEF SUMMARY This paper introduces lift shifting type six floors of three-dimensional garage design method based on Omron CP1HX40DR-A controller, completing the requirements of three-dimensional garage for city vehicle management toward the direction of automation and centralization. This design can be used to restore occupied pavement, reduce preempting, and ensure safety, in addition that it could reduce traffic congestion time, reducing the injury. On this basis, the problem has been thoroughly eliminated, including various vehicles disorderly stopping and parting in disorder, and the appearance of parking places with dirty, disorderly and poor, thus protecting vehicles away from lost, being damaged and stolen. Finally, the road is giving back to the vehicles and pedestrians, the lawn to the green space, the environment of the neat civilization life to the modern metropolis. The development cycle has been greatly shortened, based on the design about three-dimensional garage design of PLC controller. This is also a kind of inevitable of the electrification, digital and automation advancement. The thoughts and methods of this design can be applied to other scale garage and relevant problems of design. REFERENCES [1] [1] Huo Gang. Application and programmer of the CP1HPLC. China Machine Press [M], 2009.1 [2] [2] Omron Power program. Omron Corporation (China), 2008 [3] [3] BoSen Ren.General situation of Chinese mechanical parking equipment. Celebrated manufacturers of parking equipment and peripherals directory [J] :PP5-7 [4] [4] Lekang Yu Dongxiao Zuo.The development of mechanical parking. [J] Technology and management of construction machinery. 1999 1:PP 30-32 [5] [5] Fuen Zhang ? Younai Wu.Principle ? design ? set up and maintenance of AC variable speed elevator. [M] China Machine Press 1999 中文譯文 基于歐姆龍可編程序控制器的6層立體車庫設計 Zhuoran Zhang 電氣工程 武漢理工大學 武漢，中國 電子郵件：Harry zzr@126.com Zhe Mao, Hailing Wan 電氣工程 武漢理工大學 武漢，中國 電子郵件：maozhe998@sina.com 摘要： 隨著現代社會的快速發展，許多城市的車輛數量正在一直以指數的速度快速增加，特別是私家車。這些情況對這些城市交通和停車造成了巨大的壓力。這篇文章主要內容是關注立體車庫的整個結構，運行程序和電氣系統的設計等方面，其中包括硬件方案的設計思路，以及提升立體車庫整體性能。這不僅將能縮短立體車庫的開發周期，也促進停車場向集中化和自動化方向發展,對立體車庫設計有一定的參考價值。 關鍵詞：立體車庫，歐姆龍PLC，設計 停車位不足是導致城市經濟和交通的發展放緩的主要原因之一，而傳統車庫的一直使用是導致停車位不足的重要因素。在一個社區中停車位和居民家庭比例約為1:1，也就是一個家庭中至少有一個停車位，而為了解決這一矛盾而使用寶貴的商業用地是不可取的。在停車場中立體機械車庫的主要優勢就是相同車位的停車場需要的占地面積較少，這一優勢已經逐步在我們面前展現出來。相比與傳統的地下停車場車庫，立體車庫有更多的優勢。首先，立體車庫可以節省更多的占地面積。以傳統的方法停車的停車場必須考慮車輛的行駛軌跡問題，而平均一輛車需要至少40平方米進行停車操作。如果我們考慮使用地是多層的立體車庫（6層），有可能停放在該區域的車輛可達13輛，而占地面積僅為50平方米，這將節省大量寶貴的土地資源和土地建設成本。同時，立體車庫能保證他人和汽車的安全。如果在車庫有任何人活動或汽車沒有完全停止，電氣設備的控制系統將無法正常運行。這意味著，在規模的機械車庫管理時可實現人車分離，這使得立體車庫更自動化，特別是對于地下車庫。安裝這種車庫的地下停車場將省去大面積的照明系統，因此它的出現可以節約大量的能源并可以保護周邊的環境免遭破壞。 Ⅰ.立體車庫的背景分類與實現 A.立體車庫的分類 根據現在立體車庫的發展，可將它分為巷道堆垛式立體車庫，垂直升降式立體車庫，垂直循環式式立體車庫，圓形水平循環式立體車庫等。立體車庫的概念是從自動化的物料傳送系統演變而來。[3]立體車庫的使用目的是為了解決停車難的問題，尤其在發達的城市中，這是為了使有限的區域內停放更多的車輛，以節省發達城市的土地資源的靜態交通管理系統。本文提出了一個簡單的方式來設計基于歐姆龍可編程序控制器CP1H的立體升降車庫，這可以擴展到解決相關項目的立體車庫設計難題。 B.簡要介紹了升降橫移立體車庫 模塊化設計在進口的升降橫動立體車庫設計中是很重要的。它可以設計為兩到五層或半地下型車庫，車位的數目可以從幾十到幾百個。這種車庫合適于地上和地下建造車庫的特點，它的優點可概括為占用土地少，操作簡單，結構配置靈活，建設成本更低，裝飾防火和建設周期短，安全方便存儲汽車;使操作更為順暢，降低運行時的噪音。[4]這也是適用于商業，辦公室和住宅的使用。立體車庫的安全設備主要是光電傳感器，限制位移保護和緊急開關等。 C.整個系統的框架 由圖l表示，除了中央控制器PLC，立體車庫系統還可以被分為三個部分：一，機械系統，它包括柱，梁，承載板，車架，吊鉤等。二，電動系統，這部分是本文的核心，它控制整個系統的正常運作。三， 觸摸面板，它是用戶和系統交換消息的設備，用戶不僅操作該系統，還可以在故障的情況下讓操作員輸入命令或進入調試模式。 圖1。系統的結構 圖2。 觸摸屏（自動運行和手動） ?該系統的主要硬件 我們主要使用歐姆龍可編程序控制器CPH1，在考慮控制要求和硬件成本的問題上，我們采用CP1H-X40DR-A PLC的編程方法可使用梯形圖或ST指令列表。指令的長度是1到7的步驟指令，每個I/O繼電器有1600個端口，使用USB 1.1接口進行通信。顯示部分，我們使用屏幕型號是WEINVIEWMT6056i系列型號，屏幕材質為TFT，尺寸大小為5.6英寸，使用USB2.0端口，屏幕支持的分辨率為320X234，下載程序的CPU的頻率是400 MHz，運行內存為128RAM。 D.該系統的結構和功能 機械零件中與電氣系統合作的是承載板、掛鉤和鏈條。各層上除了7層以外有六個插槽,一共有37個插槽、在每一個階層上都有一個空的位置的目的是擁有足夠的空間來使裝載板移動。承載板的一層設計用來來回移動,同樣頂樓承載板也應該僅用來提升。另一個承載板在這些樓層中是為了提升和橫移。通過這種方式,該系統可以實現節約和降低其中6層中的任何空位。 此外，該系統還具有的觸摸屏系統，其中系統還可以在自動運行和手動調試模式之間切換。 在自動運行模式下，它可以讓用戶選擇某個位置的停車位完成保存的行為，同時還可以監測系統的運行。 （系統顯示綠字“系統運行”，表示系統在自動模式下無故障，可正常運行）。當系統發生故障時，系統檢測后并在屏幕上顯示為閃爍的黃色和故障代碼，用紅色背景，借助故障代碼，專業的操作員可以識別故障代碼并及時準確地消除故障。上述考慮情況現在越來越多的部門在手動調試的模式進行停車，以排除非專業人士進入該模式的機會，所以在此之前，輸入模式并有一個密碼驗證，該序密碼可以由自己設定。這將保護系統免受潛在的危險，方便維修人員維修。 圖2是曲線圖，系統自動運行和手動調試。 II.對電氣系統的分類 強電系統 高效的動力系統包括電源系統，保護系統和驅動機制，這就是電機。安裝XJ3-D對早期的電源配線，可以用來保護的三相的相序電壓，使保證電機的右旋轉。此外，這也使每些層上使用的電動機擁有相同的三相電壓。 電機的布置 在第一層上有6個橫動電機，在2到5層有6個橫動電機，因此在2到5層有起重電機，頂層部分只有7臺起重電機。布置完成后，對每個電機進行標記。例如，電動機在第二層的第三個時隙時，我們把它標記為“23”，電機前的繼電器命名KM23。在此系列連接所有的電動機都進行熱保護，任何電機的問題都會導致系統出現問題。在這運行方式下，它具有的系統穩定性并沒有受影響，但這也可以使整個系統的建造成本大大降低了。同時，維修人員可以更容易地找到問題。（我們需要做的是將每個熱保護開關一個一個地連接）。 弱電系統 弱電系統也就是控制系統，主要包括PLC模塊和5個擴展模塊和傳感器模塊。如下圖所示，右邊是輸入部分，電壓為直流24V，在左側為輸出部分，電壓為交流220V，并把他們連接起來。 這些設備的控制要求與整個系統的功能有密切的關系。在上述的曲線圖中，上述的保護設備安裝緊急開關，旁邊觸摸面板安裝有緊急觸發裝置，按下后系統將迅速停止。正面和背面安裝有光電傳感器，這是用于檢測人或不明物體闖入自動車庫系統，如果發生這種情況時，系統將會停止然后響應光電響應失敗，我們的目標是保護人和車輛的安全。相序保護器的作用是在電機卡死或正常啟動之前過電流保護，它并于邊緣交換機系列連接，主電源短路時承載板超過極限位置時，系統將切斷主要電源。 限位開關，包括向上的限位開關和向下的限位開關或左右限位開關。為了更好的實現控制要求，水平限位開關都安裝在每個車位時隙的兩側，而垂直極限開關安裝在附加的電機鏈上。有必要指出的是，第一層只安裝下和左右的限位開關，頂端層只安裝開關，這些開關能感覺到的車位板的位置，幫助完成解除車的位置控制。鉤位置傳感器是確定車輛和插槽是否有無空間的裝置。 輸出點“00 04 05 06 07”的選擇的不同，對應每個層的不同的相位，所以它也控制的電動機的旋轉方向的操作或取消。 圖3。 PLC模塊（分部） 還有其他的4個擴展模塊，可使系統擁有更多的I / O端口，圖為PLC主要部分。 III. 操作步驟 A.程序的運行 根據第一層特點，它被設計為只做橫向移動動作，從而使空間上層的面板有空間向下方移動。所以，其它層也是如此，這就是模塊化設計。當詳細研究符合要求，升降機構的運行，將承載板運行，完成保存和程序。在過程中，光電傳感器將是打開的，這情況在前文解釋。在圖2A中，采取此條件，在這個時候“加載”燈將閃爍，直到采取過程結束為止。當我們輸入“51”這個數值后，該系統將區分操作是否是通過51插槽的掛鉤保留和捕獲程序。然后將該消息的狀態顯示在屏幕上，操作者可以通過屏幕信息確認操作或取消操作。在確認后，51個承載板將等待下層承載板橫向運行完成后再向下完成穿越移動。此外，一個定時器被添加到本控制模塊，以排除水平限位開關的故障，導致穿越的移動時間過長的錯誤。如果移動的時間超過設定的時間后，系統將向操作員發出警告，并在屏幕上顯示“穿越移動時間過長”，操作者可以通過屏幕檢查出失敗的原因，并可很快 修復。向上的限位開關是否被用來感測承載板是否停在他們的應有的位子上。若液位開關無法完成正常檢測，也許是一個承載板卡在兩層之間。只有做到上面所訴的內容后才停止在正確的插槽，程序才會被被激活。一個定時器設置到起重控制裝置，具有相同的功能，作為定時器。電梯將該車輛運送地，釋放鉤子，現在的光電信號關閉，并等待為業主車輛進