壓縮包內含有CAD圖紙和說明書,均可直接下載獲得文件，所見所得，電腦查看更方便。Q 197216396 或 11970985
目 錄
1 緒論···································································1
1.1 課題的背景及目的··················································1
1.2 國內外發展狀況····················································2
2 塑件的結構工藝分析·····················································3
2.1 塑件的材料選擇及分析·············································3
2.2 估算塑件的體積和質量·············································3
2.3 分析塑件的成型工藝參數···········································4
3 確定模具結構方案·······················································5
3.1 脫模原理·························································5
3.2 確定型腔數量及布局形式···········································5
3.3 選擇分型面·······················································6
3.4 確定澆注系統與排氣系統···········································6
3.4.1 澆注系統形成···············································6
3.4.2 主流道的設計···············································6
3.4.3 分流道的設計···············································6
3.4.4 澆口的設計·················································7
3.4.5 排氣系統的設計·············································7
3.5 選擇推出方式·····················································7
3.6 模具加熱與冷卻方式···············································7
4 模具設計的有關計算·····················································8
4.1 型芯和型腔工作尺寸的計算·········································8
4.1.1 型腔徑向尺寸計算···········································8
4.1.2 型芯徑向尺寸計算···········································8
4.2 側壁厚度與底板厚度的計算·········································8
4.2.1 側壁厚度···················································8
4.2.2 推板厚度···················································8
4.3 斜導柱等側抽芯有關計算···········································8
4.3.1 斜導柱的設計···············································9
4.3.2 斜導柱的計算···············································9
4.3.3 斜滑塊的設計··············································10
4.3.4 鍥滑塊的設計··············································11
4.3.5 導滑條的設計··············································11
4.4 冷卻與加熱系統··················································12
5 注射機及模架的選擇····················································13
5.1 初選注射機······················································13
5.1.1 澆注系統的設計············································13
5.1.2 注射壓力··················································14
5.2 選用標準模架····················································15
6 校核注射機····························································16
6.1 注射量、鎖模力、注射壓力、模具厚度的校核························16
6.2 開模行程的校核··················································16
6.3 模具在注射機上的安裝 ···········································16
7 推出機構的設計························································17
7.1 推件力的計算····················································17
7.2 推桿的設計······················································17
7.2.1 推桿的強度計算············································17
7.2.2 推桿的壓力校核············································18
7.3 推板強度計算····················································18
8 連接件的選用··························································19
8.1 銷釘?shù)倪x用······················································19
8.2 螺釘?shù)倪x擇······················································19
9 模具的裝配····························································20
9.1 定模的裝配······················································20
9.2 動模的裝配······················································20
9.3 模具裝配圖的繪制················································20
結 論·······························································22
致 謝·······························································23
參 考 文 獻······························································24