購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載就能得到。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，有不明白之處，可咨詢Q:1304139763
黑龍江工程學院本科生畢業設計
目 錄
摘要…………………………………………………………………… Ⅰ
Abstract.................................................Ⅱ
第1章 緒論............................................. 1
1.1離合器的發展歷史............................................1
1.2離合器的功用................................................2
1.3離合器的工作原理..........................................3
1.4膜片彈簧離合器特點..........................................4
1．5 設計的主要內容....................................5
第2章 離合器的結構方案選取..............................6
2.1離合器設計的基本要求........................................6
2.2離合器結構設計..............................................6
2.2.1摩擦片的選擇..........................................6
2.2.2壓緊彈簧布置形式的選擇................................6
2.2.3壓盤驅動方式的選擇....................................7
2.3離合器主要零件材料的選擇....................................8
2.3.1從動盤的材料選擇......................................8
2.3.2摩擦片的材料選擇......................................8
2.3.3膜片彈簧的材料選擇....................................8
2.3.4壓盤的材料選擇........................................8
2.3.5離合器蓋的材料選擇....................................8
2.4離合器的通風散熱............................................9
2.5本章小結....................................................9
第3章 離合器基本結構參數的確定.................. .... 10
3.1離合器設計所需數據.........................................10
3.2摩擦片主要參數的選擇.......................................10
3.3摩擦片基本參數的優化.......................................12
3.4本章小結...................................................14
第4章 膜片彈簧設計................................ 15
4.1膜片彈簧的結構特點.......................... ...............15
4.1.1 H/h的選擇............................................15
4.1.2 R/r選擇..............................................16
4.1.3 圓錐底角.............................................16
4.1.4 切槽寬度.............................................16
4.1.5 壓盤加載點半徑和支承環加載點半徑的確定...........16
4.1.6 公差與精度...........................................16
4.2膜片彈簧的優化設計......................................... 16
4.3膜片彈簧的載荷與變形關系....................................17
4.4膜片彈簧的應力計算..........................................19
4.5本章小結... ... ... ... ... ... ... ... ... ... ... ... ... 19
第5章 離合器從動盤設計...................................... 22
5.1從動盤結構..................................................22
5.2從動盤設計................................................. 23
5.2.1從動片的選擇和設計................................... 23
5.2.2從動盤轂的設計....................................... 23
5.2.3摩檫片的材料選取及與從動片的固緊方式................ 25
5.3扭轉減震器設計..............................................25
5.4本章小結... ... ... ... ... ... ... ... ... ... ... ... ... ...25
第6章 操縱機構設計.......... ................................ 28
6.1離合器踏板行程計算......................................... 28
6.2踏板力的計算.............................................. 29
6.3分離軸承的選取............................................. 30
6.4本章小結... ... ... ... ... ... ... ... ... ... ... ... ... 31
結論................................................... . 32
參考文獻.........................................................33
致謝.....................................................34
附錄A....................................................35
附錄B....................................................36