購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載就能得到。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，【有不明白之處，可咨詢QQ:1304139763】
礦泉水瓶蓋注塑成型工藝及模具設計 摘要 本設計課題為礦泉水瓶蓋注塑成型工藝及模具設計 體現了部分螺紋類塑料零 件的設計要求 內容及方向 有一定的設計意義 通過對該零件模具的設計 進一步 加強了設計者注塑模設計的基礎知識 為設計更復雜的注塑模具做好了鋪墊和吸取了 更深刻的經驗 本設計運用塑料成型工藝及模具設計的基礎知識 首先分析了模具的發展趨勢 材料的特性塑件的成分及性能要求 為選取澆口的類型做好了準備 然后估算了塑件 的體積 便于選取注塑機及確定型腔數量 最后分析了塑件的特征 確定模具的設計 參數 設計要點及推出裝置的選取 本塑件有螺紋結構 但螺紋較淺 為了減少工時 節約成本可以強制脫模 本副 模具的設計中 上斷面下部 有一個較博的圓環 在制造時加工不方便 但可以制造 小電極 采用電火花技術 關鍵詞 注塑模 澆口 強制脫模 推板 Pro E Design topics covered in category for njection mold design Abstract Design topics covered in this category for the injection mold design part of the screw type of plastic parts design content and direction of a certain design significance Parts of the mold through the design the designer has been further strengthened by the injection mold design based on knowledge for the design of more complex injection molds made and lessons foreshadowing a more profound experience The use of plastic molding process design and die design of the basic knowledge the first analysis of the development trend of the mold the material characteristics of the plastic parts of the composition and performance requirements select the type of gate prepared for the then estimate the size of the plastic parts For selected cavity injection molding machine and set the number of the last of the plastic parts of the features of the design parameters established mold design elements and the introduction of the device selected The plastic pieces are threaded structure but less thread in order to reduce working hours the cost savings can be forced Stripping The deputy dies in the design on the lower section have a Bo Circle in the manufacturing processing inconvenient but we can manufacture of small electrodes used EDM technology Key words mandatory injection mold gate Stripping push plate Pro E