購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載就能得到。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，【有不明白之處，可咨詢QQ:1304139763】
摘要 液壓缸是液壓系統執行部分 它是一種壓力流體的機械能來實現直線 往復運動或往復擺動運動能量轉換設備 液壓缸根據其結構形式 可以 分為兩類 活塞式液壓缸和活塞式液壓缸 活塞式液壓缸 活塞缸的出 口壓力和流量 輸出的推力和進度 因為主機和主機的液壓缸機構有直接的聯系 對于不同的主機和機 構 不同的用途和工作條件的要求 液壓缸的類型和結構是千變?nèi)f化的 沒有統一的規范 不象液壓泵和液壓閥已經標準化了 因此必須根據實 際需要自行設計 液壓缸的設計 液壓缸的基本原料是負載值 加載速度 中風 液壓 缸的結構和安裝要求 液壓缸的設計計算主要是確定液壓缸的壓力和流 量的使用 和液壓缸強度的組件檢查和性能檢查 等等 液壓缸的設計步驟 1 根據液壓缸的工作特性 選擇液壓缸類型和安裝方法 2 根據動力和運動分析 確定主要尺寸參數 3 設計主要零部件的結構 4 液壓缸的性能計算 液壓缸的設計和使用正確與否 直接影響其性能 沒有故障 在這方 面 經常遇到液壓缸安裝不當 活塞桿在部分負荷下 液壓缸或下垂活塞 和活塞桿的壓桿不穩定等等 在本設計中 充分考慮到了這些設計中應 該注意的問題 并且針對液壓缸兩端需要焊接絞座的問題 對金屬的可 焊性進行了分析 關鍵詞 液壓舉重機 液壓缸 活塞桿 Abstract The hydraulic pressure jar is an execution component in the hydraulic pressure system It is one kind transforms the liquid Mechanical energy to realize the straight line reciprocating movment or pressure reciprocation oscillating motion energy conversion installment Hydraulic pressure jar according to their structure form can divide into piston jar and post fill in two kinds of jars The piston jar and the plunger jar input for the pressure and the current capacity outputs for the thrust force and the speed Because the hydraulic pressure jar has direct contacts with job organization on host computer and host computer Regarding different main engine and organization along with use and operating mode request difference hydraulic jar type and structure ever changing does not have the unification the specification Did not like Hydraulic pump and hydraulic valve already standardized therefore had independently to design according to the actual need Designs the hydraulic jar the basic firsthand information is the hydraulic jar load value the load velocity of movement the stroke value the hydraulic jar structural style and installs the request and so on The hydraulic jar Mainly is to determine the design calculation hydraulic jar the working pressure and the current capacity and carry on the intensity Check and hydraulic performance jar spare part checking computations and so on Design step of the hydraulic pressure jar 1 According to the operating mode characteristic of the hydraulic pressure jar choose the type of the hydraulic pressure jar and installation way 2 Analyse according to dynamical and movement confirm the main size parameter 3 Design the structure of the main spare part 4 The performance of the hydraulic pressure jar is calculated The hydraulic jar design and the use is correct or not directly affects its performance and easy otherwise to break down In this respect Meet hydraulic pressure jar install improper cylinder rod is lean towards year to bear hydraulic pressure jar or piston flagging and cylinder rod keep pole mistake question such as being steady often In this design have fully considered the Problems should be paid attention to these designs and needs to weld in view of the hydraulic jar beginnings and ends twists the place the question has carried on the analysis to the metal weldability Key words Perform component Firsthand information Design procedure 目 錄 第一章 引 言 1 1 1 國內外的發展?fàn)顩r 1 1 2 液壓缸簡介 4 第二章 設計計算 6 2 1 液壓缸的初步設計 6 2 1 1 液壓缸的工作壓力 6 2 1 2 初選缸筒內徑及活塞桿直徑 7 2 2 液壓缸主要技術性能參數的計算 8 2 3 液壓缸的主要部件設計 8 2 3 1 缸筒的設計 8 2 3 2 活塞的設計 10 2 3 3 活塞桿的設計 11 2 3 4 端蓋上螺栓的校核 12 2 3 5 導向套的設計 14 2 3 6 缸筒底部厚度 15 2 3 7 密封圈的選用 15 2 3 8 開口銷的選用 16 第三章 金屬的可焊性 17 第四章 液壓缸的選用 18 4 1 液壓缸主要參數的確定 18 4 2 使用工況及安裝條件的確定 18 4 3 緩沖裝置的選用 18 4 4 密封件的選用 19 4 5 工作介質的選用 19 結 論 20 參考文獻 21 致 謝 22